Reviews
Exhaust flange, etc.
It is used to remove the exhaust pipe or when the bolt nut is difficult to access due to obstructions, etc.
This is a useful item because there are times when it is not necessary to remove obstacles.
The texture is like KTC!
View detail
I have one.
For some reason, I have one in Torque.
Torque is often used in Harley, so it is useful to have.
View detail
Not for everyone.
It is a hexagonal, low-head Profile Socket.
It is sold without any warning, but as a result of prioritizing handling, it is short and easy to use in some situations, but on the other hand, it cannot be used in places where Bolt needs a little length on the Socket side, such as a longer Penetrating Nut or Cap Nut. (Standard length sockets from other manufacturers or semi-deep sockets from ZEALBrand are required.)
Therefore, if you want to use one type of Socket for all parts of the system, it is not recommended at all.
For those who are willing to use low head whenever possible where sockets are used, and only replace them with semiDeep or other companies' products for exceptions after a bit. Beginners and Light users should buy something else. It is also not suitable for circuit use where you want to limit the number of tools you bring with you.
However, the rattling and bending when using Socket is close to Zero, so it is definitely reliable in usable areas.
View detail
under compulsion
I lost my 24mm Socket for Elumi's Castle Nut, and although I rarely use 24mm, I needed it, so I purchased the SK11 SK11 Socket 24mm this time, considering the cost performance.
9.I was torn between 5mm and 12.7mm, but decided to go with 9.5mm since Motorcycle uses 9.5mm as a base.
The quality is good and they are a reliable Manufacturer that I have purchased many other things from.
View detail
3/8 might be better for the final tightening.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 4mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
For 8mm hexes, the Torque is so large that it is safer to use a 3/8 insert depending on the location, but for hexes located in tight spaces or at the back of the room, a slim 1/4 is not acceptable.
I am using a 3/8 hex socket made by KTC, but the hex shaft (tip bit) is screw-fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
Compact 1/4 Inch Socket is convenient!
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 6mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
I like the way it's built with no Bit missing.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 4mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
Recommended by KTC
I would like to add that the product description was missing.
Hexagon socket with a 6.35mm (1/4inch) insertion angle. 3mm in size.
This time, I bought everything from 2.5mm to 8mm.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
Recommended by KTC
I would like to add that the product description was missing.
Hexagon socket with 6.35mm (1/4inch) insertion angle and 2.5mm size.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
View detail
I just bought #6 for now.
Basically, Hexagon Bit Socket is not for regular use with long length, and I prefer to use the shortest possible Hex, but I buy Single Item at Koken only for those parts where I have no choice.
This #6 was purchased for use on the bottom portion of the Upright Front Fork, against the bolt that is located at the back of the fork.
Since it is not a place that is used that often (since it is only touched during O/H of Fork), I had been using a cheap Brand's one, but when I used it on a tightly stuck partner, I could see the twisting with my eyes, and I realized again that cheap is cheap after all.
This is especially true for the long length of 75mm, but if you are a few hundred yen stingy and try to screw up the bottom bolt, you will be in for a world of trouble.
If it's Bit or something like that, I'm sure that Kohken is reliable, but I wonder how far they can go when dealing with Bolt, which is of low quality to begin with.
View detail
Made by TONE for peace of mind. Personally recommended over KTC.
I would like to add that the product description was missing.
This is a Hexagon socket with a 6.35mm (1/4Inch) insertion angle. This size is 5mm.
2.I bought everything from 5 to 8mm at once.
Compact tools are easier to use for attaching/removing exterior and small objects, so they are used separately from 9.5mm (3/8) tools.
It is useful to use this Socket together with a 1/4Inch THandlebar or a 1/4 Driver-like Handlebar.
I am using KTC made as 3/8 Hex socket, but the Hex axis (tip Bit) is Screw fixed and can easily come off.
So I bought more 1/4s and made them TONE. This is good because the tip Bit is press-fitted so it won't fall out.
Can I recommend this product to my friends and acquaintances? ⇒ YES... You can RECOMMENDATION.
View detail
Stable KTC
I chose KTC in part because of KTC.
I have been using SIGNET tools for a long time, but I also like KTC as a Brand with stable quality.
Since it is a tool, a reliable Brand is good for mental stability.
View detail
Expensive! But if you don't buy this tool, you can't replace the Exhaust System!
[How is it used?
This tool is essential for removing the O2 Sensor of the Exhaust System.
I purchased this product when I exchanged it for YOSHIMURA's One piece.
Was the one you received as per Image?
Tools only, nothing else attached.
How was your experience with it?
Although I was concerned about whether Torque would really be applied, I was able to remove the Sensor without incident.
[Points to note]
CB1100's O2 Sensor is just too hard!
I was finally able to remove it while blowing CRC.
It may be tough with low-precision tools.
How did it compare to other products?
Quantity:There are inexpensive tools available as Set items, but I think this one is sufficient since it is only used for CB with only 17mmSocket.
The other tool is also available from Snap on, but is more expensive at over 10,000 yen, so we would like to have this one before it sells out.
View detail
Socket
Combined with the Small Type Ratchet, it is very useful for compact use in tight spaces.
Single Item sales, affordable prices are helpful.
View detail
Ordinary Socket
Motorcycle Stand Lift I purchased this for the purpose of lifting Jack.
Lift up the BOLT Shoulder Bag, but it is a one-person Motorcycle straddle and cause the Jack under the belly Quantity.:Set.
At this time, the BOLT Shoulder Bag has a very good footing and a low center of gravity, so the Motorcycle is less likely to become unstable even when bending forward.
When I operated the jack for the first time after purchasing it, I used my MONKEY Wrench, but I thought a manual ratchet wrench would be more convenient for operating the jack, so I decided to use this product, which has a standard that fits the ratchet.
Since the main application is Jack elevation, I think the durability is infinitely etc.
I have operated with Impact wrench, but it is difficult to operate Throw alone, so I think Hand tool is better without danger.
View detail
angle
It is useful because the angle can be changed for use in tight spaces.
It is reasonably priced, compact, and takes up little space for storage.
View detail
As an on-board tool for motorcycles
I purchased this as an on-board tool for my motorcycle.
I had a Socket set as my main tool, so the low price and the One Touch Socket Holder were the deciding factors in my decision to purchase it as an in-vehicle tool.
The quality is perfect for normal use, as is the low price.
View detail
Gold is distinctive
Available in 3mm to 12mm, Quantities are more affordable than Single Items.:Set is a better value.
I think the quality is good enough, as I have never had any licking while using it.
For clarity, we have used TEPLA to indicate Size.
View detail
It's cheap
It is inexpensive, of good quality, and useful.
Theplastics are used to indicate Size for ease of use.
It also comes with a One Touch Socket Holder, which is a great value.
View detail
For maintenance.
The length is just right and can be used for different purposes.
The longest one in particular is now required to remove the Plug.
View detail