Reviews
Contact protection Cap.
[How is it used?
It is installed to protect the Stop-lampWiring contacts when the GIVI box is removed from the vehicle body side Mount base.
Was the one you received as per Image?
Since it is only fixed by inserting the two Pins inside the protective Cap, it seems like it might come loose and come off due to vibration, but so far it is safe.
Was the installation difficult?
Simply place the protective cap over the contacts and push it in. If you push it in too tight, it will be difficult to remove, so push it in with moderate force. When removing the cap, insert a thin slotted screwdriver into the gap and gently pry all the way around the protective cap.
How was your experience with it?
Unfortunately, it is not waterproof, so before covering with a protective cap, a thin layer of grease is applied to the contact points to prevent rusting.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
If it was going to provide protection anyway, it would have been nice to have waterproof performance as well.
Other items that would be helpful
Point or hang of installation:Do not push in hard.
Availability of Instruction Manual:Instruction Manual is not included.
Opinions and requests to Manufacturer:Waterproof performance would be nice.
View detail
Fits: BMW C400X K09, BMW F800 GT K71, BMW F800 GT, BMW F800 GT, BMW F800 R K73, BMW F800 R, BMW F800 R, BMW F800 R, BMW F800 R, BMW F800 S K71, BMW F800 S, BMW F800 ST K71, BMW F800 ST, BMW G310 GS K02, BMW G310 GS, BMW G310 R K03, BMW G310 R, BMW K1200 GT K44, BMW K1200 GT, BMW K1300 GT K44
Purchased with the replacement of a vehicle
I tried to use the VARIOTop case that was installed on my BMW F750GS on my newly purchased G310GS, but the key shape is different and cannot be locked.
I thought about buying a key from a dealer, but I had already given away my F750GSBody and the key number was unknown, so it seemed like a waste to go to the trouble of ordering a regular key just to open and close the top case.
Then, I searched on webike, thinking that if I had a horizontal groove type Wave key, I could use it only by replacing the Plate of the Key cylinder.
OEM Key Quantity:2pc. Get Cylinder with Set 。
As expected, the key lock of the Top case was created by simply replacing the Plate in the existing key cylinder with the purchased key.
Cylinder is not necessary for VARIOTop case because it is not suitable for VARIOTop case, but it may be used in the future when replacing the vehicle, so it should be kept.
OEM key quantity for less than 3,000 yen using Point:2pc. We are satisfied with the Set we got.
View detail
Flat bottom, no slipping.
I'm starting to think it's a little pricey, but the OEM is Just fit for the bumps! The capacity is a little less, but the Flat bottom makes it easy to use because it doesn't slide around. View detail
Fits: HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin Adventure Sports ES, HONDA CRF1100L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin, HONDA X-ADV
HONDA Honda Top Box Lock
Material:It is plastic, so it looks cheap.
The controls are not as Snap as I had hoped.
The lock to the carrier and the top lid lock at the same time.
I think it would be more convenient if they were separate.
View detail
Fits: YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA MT-09 SP, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R25, YAMAHA TRACER900, YAMAHA TRACER GT, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT-10, YAMAHA XMAX
Key Cylinder B for yamaha euro tpo case
I choosed type B of key cylinder because it come with seperated key. Easier for me to open the case even when the bike is idling while the engine is still started. View detail
Dress-up made easy!
It is easy to install. It is easy to install. The grade of the appearance goes up just by putting it on. View detail
Wiring is too small.
The wiring to be installed in the box made by Manufacturer was broken during the second opening and closing.
The wire was torn out from where it was fastened with Nut.
I reconnected it myself.
Also, the contact with the Body is poor, so it flashes with vibration
I can't use this.
The build quality is lousy for the price.
I'd like to improve on that.
I have no choice but to connect it directly and use it somehow.
I'm not sure if I would recommend it to others.
View detail
Fits: HONDA Gold Wing Tour DCT, HONDA Gold Wing Tour, HONDA Gold Wing Tour DCT Airbag
Wonder why it wasn't there in the first place.
The rear trunk is bare of resin and may be damaged.
Because the Rear trunk of the 21-year-old model has become large, the previous Matte is too small, you need to pay attention.
After 21 years, I bought a MODEL exclusive product, and naturally Just fit.
The view of Trunk has been given a luxurious feel.
View detail
Fits: Others E45NJ, Others E36NJ
Used for NBS, not GIVI.
Not GIVI. NBSRear box 32L TypeB I used it to say.
I couldn't find any info on dimensions etc. so I bought it on a total hunch.
It was Just fit.
Or is it a component that doesn't make that much difference no matter what you choose?
View detail
Fits: Others E52 : E50 : TRK33N : TRK46N : E460 : E470 : E450 : E370 : E350 : E340 : E33 : E300 : E300N2 : E30TN : E260 : V35
Can be used for Chinese Top case
I use a Chinese Top case and the opening Stopper breaks relatively early under the load of daily use.
So I only used Repair Parts here.
Quantity of Orange Screw Receivers in the hole:Since it is necessary to press-fit when setting, some grip strength is required. If you are weak or female, you may need to use a temporary quantity:After Set, step on it to press it in.
Quantity:After Set, there is no discomfort for now. I'll see how long it lasts. I think it's better to replace it as soon as it breaks.
View detail
Rattle prevention
Z126A is Base for GIVIMono-lock (GIVI part number:M6M DAYTONA part number:91333) Repair Parts
Z126A (Height 9.5mm)
GIVIUniversalBase was used. (GIVI part number:MP60N DAYTONA part number:31335)
Rubber stopper for MP60N is Z126 (Height 8mm)
[After exchange]
This is the first time I bought a top case and it had a rattle between the base and case.
No tools are required for replacement, and it can be installed without any problems without any modification.
View detail
Look carefully before you buy.
It's my fault that I didn't check well, but I didn't expect the Seal of PelePera to come at this price. I was disappointed because I thought that Aluminum Plate Emblem was coming and I was waiting for it. If it was a little cheaper, I would have been happy. View detail
Consumables.
Because it is a consumable that wears out while using it inevitably, it is a Large strange help because it can be easily obtained in parts by mail order. View detail
Fits: HONDA CRF1000L Africa Twin, HONDA CRF1000L Africa Twin Adventure Sports, HONDA X-ADV, HONDA X-ADV (RC95-1200001-), HONDA CRF1100L Africa Twin Adventure Sports ES, HONDA CRF1100L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin, HONDA X-ADV, HONDA CL250, HONDA CL500
Quality, price and ease of use are passable!
The quality/quality of the product is very good for the price.
It was the lowest price compared to the price/other Shop.
It was easy to use, with two side pockets and more.
These are Honda OEM products, so the size in the Top box is also Exactly
Large Good and satisfactory product.
View detail
Just fit
It's a great way to keep the Helmet in trunkSpace clean and prevent Wound from getting on the Helmet and Helmet inSpace. View detail
Utilization to E43
I bought it to divert other than the Lamp part.
I think it's better to wear a high mount lamp when installing the box because the box makes it difficult to see the tail lamp.
Both the base, the bottom of the box and the top of the box are molded so that wiring and terminals can be attached, so they are not compatible, but they can be mounted with no problem.
Because the Lamp part cannot be pimped out, WaterproofLED Tube is attached and connected to the upper terminal.
I'm thinking it would be nice if it was possible to draw in 3 terminals, although it's 2 at the moment, so that I can use USB power supply etc. inside the box, but does anyone else have any sympathy for this?
View detail
It's a consumable product …
Almost every day.
Every time you remove it and use it, it wears out quite a bit.
I'm grateful that they sell Repair Parts, but this rubber part is trapped to stick to the bottom of the box and get lost if you don't notice it, and the box will rattle and crack in the worst case.
I put one bag in the box in case I lost it.
View detail
The size doesn't fit
It's a small part, so I bought it as a spare in case I lost it
When I tried to fit it together, it didn't go deep enough
Cutting work is carried out by using Cutter, etc
I'm a little disappointed that I can't get a Smooth insertion
View detail
Bright and as expected
It's a bit high as a Cost to spend just to add a stop-lamp, but to be safe The Instruction Manual is not easy to understand, but it's a good choice for all It was not hard to tell since it fits on the Top case side Because the box that I installed is an old one, poor contact was likely to happen at the contact point between the lid and the bottom But I dealt with it by bulking up and so on It's a good product, although the detail work takes a little longer View detail
Fits: YAMAHA NMAX, YAMAHA NMAX155, YAMAHA MAXAM, YAMAHA BWS125(BWS), YAMAHA CYGNUS X SR
Color:Unpainted but highly textured
I bought it in White:Unpainted, but the OEM Blueish white cocktail and the color is The texture is surprisingly good because of the similarity and sheen
I painted it because I wanted to match the tank and the color perfectly, but …
But if possible, I'd like CaseBody to be Standard Equipment from the start Where
It seems a bit pricey to buy this alone
View detail