Reviews
Ninja H2 OEM reservoir Tank diversion used for Custom
I bought Nisshin's Master cylinder to install the reservoir Tank of Ninja H2.
【What made you decide the purchase?】
I found an article in Nisshin 's Master cylinder that made up Ninja H2' s reservoir tank in a certain blog, so I bought this Bracket according to the information on that blog.
【How was it actually used?】
In Bracket which made plate-like Aluminum standardized in Nisshin's Master cylinder L-shaped, if you slant the Master cylinder, the reservoir Tank will also be inclined together, but if this is a Bracket Bracket itself has a slope on the MASTER side so that even if the master cylinder is tilted it is possible to keep the reservoir Tank level.
Since there is a negative pressure in reservoir tank, even if tank reservoir Tank itself is somewhat inclined, there is no particular harm, but at least if it means to make it look better at least it is not a significant Bracket for Large Is not it?.
【Mounting was difficult?】
Just remove Bolt and Nut and replace it so anyone can easily install it as long as there are tools.
【Please tell me the installation point and hang】
As with me, when you exchange reservoir tank together, I think that once you have decided all the positions and inclination angles and final tighten it will not be a hassle twice.
[Is there anything I was disappointed about?]
nothing special
【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it will be in an expensive category if it is considered as BracketSingle Body.
If it is a little cheaper it will be easier to buy.
【Have you compared items?】
nothing special
[Others]
Is not it essential to install OEM reservoir tank of Ninja H2 which is recent CustomTrend.
Besides this Bracket
- Posh H Type Rubber 100202
We made it using.
Even if you would like to organize brembo's Tank even for non-Ninja H2, I think that it's also ant to collaborate using this Bracket.
View detail
There have been problems can not be fixed tank I can simply have the product fixed position, And I just make plastic hand, reached my request *** , And I just sculpted with my hands to meet my requirements
There have been problems can not be fixed tank I can simply have the product fixed position, And I just make plastic hand, reached my request *** , And I just sculpted with my hands to meet my requirements View detail
Fits: KAWASAKI Z1-R2, KAWASAKI Z1-R, KAWASAKI KZ1000MK-2, KAWASAKI Z1, KAWASAKI Z2, KAWASAKI Z1-R2, KAWASAKI Z1-R, KAWASAKI KZ1000MK-2, KAWASAKI Z1, KAWASAKI Z2, KAWASAKI Z1-R2, KAWASAKI Z1-R, KAWASAKI KZ1000MK-2, KAWASAKI Z1, KAWASAKI Z2
Purchase
I exchanged from Nisshin's Tank Bracket. Tank Bracket positioned from the beginning is sold from various places, but Cowl - I bought this product by bothering me with interference with Inner cowl and tried to bend it to an arbitrary position by myself. View detail
It seemed unlikely Bracket
I used it to divert Kawasaki H2 Reserver tank. This and POSH's H Type Rubber (http : / / www. webike. net / sd / 1257302 / ) Is used.
It is exactly the same as Length, but it is a difficult point that you can not adjust the angle. Pliers were sandwiched between Dustcloths and the angle was adjusted so as not to be scratched. Because it is Aluminum you will hear what you say easily and easily. If it solves it, Bracket that does not claim is felt nice.
View detail
Good shape.
BremboRCSRadial master I purchased it when installing. Mank can also be mounted on the best vest of Tank! Material is also good for rust and others, but to slightly bend the angles of Tank, there might be a little power! But it is quite easy I am satisfied because I was able to attach a tank to Beauty!
View detail
Tank set
I bought a Clutch lever, but I did not know what to buy other parts, but I found this Tank set so I bought it. Installation itself is easy, but adjustment of the length of Hose is necessary. View detail
Finally I could see it.
MONKEYRear sticking to Normal step with disk formation.
If it is Rear Sets, you can choose from a lot of items, but in Normal step, there are various restrictions, there was no item of your choice in there.
This product can be installed if it is Normal frame regardless of the shape of Clutch cover.
As expected the Drum brake and the different disc brake work well.
It's comfortable without being tired at Normal position to PetitTouring with friends.
View detail
I Bought the G-CRAFT master cylinder mount kit 2 for my brake disc conversion. The quality was great and was fitted perfectly. Since i use Yoshimura cyclone (sidewinder) exuast, the normal rear master cylinder won't fit. G-CRAFT is an highly recommended b
I Bought the G-CRAFT master cylinder mount kit 2 for my brake disc conversion. The quality was great and was fitted perfectly. Since i use Yoshimura cyclone (sidewinder) exuast, the normal rear master cylinder won't fit. G-CRAFT is an highly recommended brand well crafted and design was superb. View detail
It is a good feeling.
Although it was also in the note of Manufacturer, there are possibilities that Wrinkle and Crack will enter if it is too bent. The Clutch side was able to bend it neatly but since the Brake side was twisted + bending at the position of Tank, Wrinkle entered into the painting. * I could install without changing the Hose on the Clutch side but since I changed the Hose on the Brake side, if I exchange the Bracket I will measure the Length and buy Hose and the Tank will be slanted.
View detail
I am satisfied with the high degree of processing freedom of Bracket.
I used it for Brake's separate Tank.
Bracket attached to Nisshin radial was somewhat like Bracket at Home center so I did not like it, so I got lost.
The point of selection is the ease of processing and the color of Gold.
Fix the driver to the vice and insert the driver first to set the mounting hole to 90-degrees.
After that, I attached it to a separate body tank and bent it gently to make it the angle of your choice.
I thought that wrinkles would come in because of Aluminum, but I could bend it beautifully without such a thing.
I do not know what will happen if you bend it suddenly, but I think that if you bend it slowly you can process it quite freely.
Because the price is also cheap, it is recommended for those who can not be satisfied with the included Bracket.
View detail
It was easy to process.
Bending work was also carried out slowly, making it beautiful.
Although it is after processing, Aluminum's unique Wrinkle is also difficult to enter, I am satisfied with Large.
If you are looking for your favorite MASTER position, please try it out!.
View detail
Fits: その他
I just wanted to make it Black, but ...
【What made you decide the purchase?】
I just wanted to match the color, that's it..
Well it's because Black was originally an option.
【How was it actually used?】
Because the former was Silver, it became the same color as the Holder kind and it was tightened.
It looks good..
【Was it difficult to install? (Hard parts case)】
As it is tightening only for Bolt, nothing is difficult if it is a person who can use an on-board tool.
【Please tell me the point of installation and hang (in the case of Hard parts)】
As it is an Anodized product, I think that it is better to be aware of peeling when tightening Bolt.
While writing such a thing, I noticed that I saw a picture and peeled a little bit ... It is a bit sad.
[Is there anything I was disappointed about?]
Cost that took a while to change things other than color ... whether it was changed with my own intention ...
【Hope for Manufacturer - Please let me know if you have any improvement points]
I mass-produce such Small things carefully, so I think that it is Large strange.
Just as I make these kinds of Brackets sometimes, I realize that.
However, it is also true that it is saved if it is a little cheaper because it is listed as Repair Parts.
【Have you compared items?】
There is none.
Dare to say, it is the core Silver for the master Cylinder from the former, so it may be a comparison to want to change it.
[Others]
The color matching of these Small objects is very effective as Small technique.
Just because Cost takes more than expected, I want to be careful not to waste it at Timing to do.
View detail
Because I did not want to spend the past here alone
【What made you decide the purchase?】
Actually, I had a familiar Bracket of Silver, but I was disliked because it was around MASTER too, so I was disliked ... Because it's so much a sense that colors match.
【How was it actually used?】
Conversely, it can be said that just changing the one you used to the same new one.
So, I do not have much impression, but it looks like the color has become the same and it got tightened and it looks better and it looks better.
【Was it difficult to install? (Hard parts case)】
Since it is a Bracket to the last, only tighten each Bolt.
It is not difficult..
【Please tell me the point of installation and hang (in the case of Hard parts)】
It is a peculiar Black color, so it is sad that even if the color is removed, it is good to temporarily tighten with a finger while fixing the position and tighten the Holder side after the Tank position is decided.
[Is there anything I was disappointed about?]
Although not particularly, Bracket is only Bracket ...
【Hope for Manufacturer - Please let me know if you have any improvement points]
Products of these lines are obliged to be so, but it is appreciated if it is a little cheaper ...
I felt it especially just for making my own work.
【Have you compared items?】
Originally planned to be attached to Mirror Holder, it is not particularly compared with something.
In the first place I also wanted to make the color different though I was using it.
[Others]
It's a good and bad Aluminum bar, Bracket.
I think that you can use anything unless you are particular about OEM.
View detail
The degree of freedom is high.
Tank can be installed freely.
There is also rigidity, so you can definitely set.
However, I think that it will not be the position I thought, as it will be impossible unless Hose lengths match.
Because it is not preferable to bend it many times, I think that it is necessary to decide at once.
View detail
Cospa best
In trial and error about Master Cylinder Bracket on Brake side of ZZr 1400, finally I attached L-shape to Mirror HolderClamp. By making this form, I changed a few Master Cylinder Brackets and finally decided on the L shape of Nisshin's Repair Parts which is coming out of DAYTONA,. I applied it and it was deformed and it looks bad, so I made it to a POCH product this time. Is the hole in Design? □ With the difference Unive
I am satisfied with Large because of the finish of Image.
View detail
Trial and error 2
I bought it as Master Cylinder Bracket of Clutch & Brake attached to Bar handle.
This product is MASTER and attached to Linder Bolt and Washer are accompanied by the place is kind, but I think that it is an expensive part as a Bracket kind Single Body.
I bought it for Clutch & Brake's Master Cylinder Bracket, but actually it was possible to install Hose in only the Clutch side or adjust the angle and install it in a proper shape, but the shape on the Brake side is incompatible with this product It was. I planned to use it by bending it but it is a hard part Pliersetc. Then, it was not possible to process as I thought.
I think that it is good if the shape fits well because it is a strong part.
View detail
Inverse to Image
We are mounting Master Cylinder Cup at Mirror mounting position on our Separate handle.
Because the Handlebar position is H-shaped, CylinderCup tilts considerably in OEMBracket, so we purchased this product without particular investigation from Manufacturer name, conforming Cylinder, product name.
I tried to install it, is that the opposite angle?
In OEM 90-degrees's Bracket, Cup is tilted to Right, so if we replace it, it was expected to be further inclined to Right by about 15 degrees, so it was a good deal.
I think that it would be very useful as a Bracket option if I did not fit and if I had it mounted in a different place.
View detail
Cospa Bracket
I was coloring Master tank's Bracket and I chose it by shape and price. Bolt and Bracket of the Holder part of the Handlebar are rested and installed, but the color around the hole part of Bolt flakes off. For the time being Touch pan after positioning. I think that there is Cost performance and it is good..
View detail
To fix Master's Tank
GALE SPEED Master cylinder (Mirror Clamp) Purchase for Tank fixation.
Because I was not particularly concerned, I chose this Posh's one found in a mass merchandiser, not expensive Bracket of GALE SPEED.
Color chose Blue, but later "Is it too flashy?" I think, as I increased the Blue Parts it started to look like it.
- As the overall sense of cheap can not be denied, the sense of tentatively is strong. It easily scratches.
- When using NissinTank + Gail MASTER in combination, the handling becomes cramped, so if you purchase Nissin's Tank set, you need to separate Hose separately.
View detail
Come to the details of Dress-up
I found it at a certain Motorcycle supplies shop and bought impulses.
If you look as Bracket it is expensive, but if you want to dress up to the finer part, something is quite different just by replacing this Bracket.
It is a part that comes into my eyes at will in case of getting on and off, so it's like casually shining Bracket and Tension will go up as well.
By the way, since the coating of Anodized is quite weak, it will peel immediately if you do not care when attaching and detaching the fixed Bolt.
I have also done it, but since it is not a prominent part, I am using it as it is.
View detail