Reviews
I'm glad it's rust resistant!
I used it to replace Mirror on an AddressV125 that a friend gave me! It works normally!
It would be nice if the design was a little more unique or better made!
View detail
It's easier to ride
About installation
Since it was originally for S1000F, drilling was necessary, but there were no interference or Cable issues.
In the case of GT, you don't have to worry about Mirror, so you can decide the angle freely.
Impressions after installation
The height is only slightly more forward than NORMAL.
The aperture and angles make it easier to get down and allow more freedom for the upper body.
It also reduced the strain on my back and ass and made them more comfortable.
View detail
It was a little long for me.
[How is it used?
After six months of hanghang and Restore&Custom work on the LITTLE CUB, I thought I'd get comfortable with the next stage of the project. First, we need an external power source. I started looking for a USB power supply, but realized that there was no place to install them, so I looked for a Mount Bar in Webike's product introduction section and bought a Multi Bar from Made by HURRICANE, which had a safe design.
How did you like it?
Although I knew it existed until now Messy around the Handlebar. The Mount bar had never been used before because I had the impression that it was too heavy.
The fact that I had a safe length and design for my first Mount bar purchase and I was a teenager. Separate handle (Handlebar of Separate type)". Speaking of Other Brand Products of "HURRICANE It was an Image that I was not surprised to see. Finally, I too will buy HURRICANE products." I bought the Multi Bar at Tension...but the bar was a little too long for my use.
Please don't get me wrong, the product itself was a good product with good rigidity, but for my personal use, I would have preferred a shorter length, so after much thought, I replaced it with a Mount bar made by another company.
We wanted to use a Short Type Mount Bar to make it as Refreshing as possible, since we only need to be able to fix the USB power supply and Smartphone Holder.
How did it compare to other products?
If it is a MAJOR Manufacturer's product. "A damned glitchy piece of junk." I don't think there are any.
Before you buy Which car? of Which part? and there you want to install it in What do you want to install?" I think that Risk can be reduced if you take into account the following before making a purchase.
[Points to note]
This product is a type that is attached to the Mirror Holder by fastening it to the Mirror Holder, so it is easy to set the quantity to a position that is easy to use.:Once set, please tighten and secure each part firmly, otherwise you will be in a hurry if it loosens while driving... (This is a testimonial.)
Other items that would be helpful
The deciding factor in the purchase
As I mentioned above, I didn't even understand the difference between the Mount bar and I didn't think it through. HURRICANE Products I bought this product only because it was a very solid product with no fault of this product over and over again.
【Included Parts:presence or absence】.
Bracket for connecting Mount Bar Body and Mirror Holder, 2 Washers and Spring washerQuantity:1pc. and Nut included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
It resonates with my father's generation. "HURRICANE BrandName, we look forward to continuing to serve you with a variety of custom parts at affordable prices.
View detail
Cost performance is good
From the beginning, I felt Handlebar was too far away and was looking for a product like this.
After the exchange, it wasn't as close as I had hoped, but I had more room in my arms.
I am very happy with the replacement because I feel less tired.
View detail
Handlebar Straying
I changed a lot of things with EFFEX→Archi→BEET→Condor→Conti2.
I write this only as a personal opinion.
EFFEX→not much different from NORMAL and tiring.
Archi→ easy to ride but not great looking.
BEET→ easy to ride, but forward leaning is tiring.
Condor→ Easy to ride, but I don't like the way the Clutch Cable hits the Meter, doesn't look good in a bikini.
Conti2→A little higher and A little tighter than BEET, but still tiring after a long ride.
Now I plan to try European1 type.
View detail
HURRICANEForwardCondor Handle
Position is easier with a moderate forward lean. View detail
Fits: HONDA CB1100 EX, HONDA CB1100 EX, HONDA CB1100 RS, HONDA FUSION, HONDA FUSION, HONDA FUSION
Handlebar brace
Very well made item and fits great with the barkbusters hand Guards, the 280mm fits the Honda cb500x perfect. Thank you webike! View detail
Fits: YAMAHA SR500, KAWASAKI ZEPHYR750 RS, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, YAMAHA SR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR400χ
It makes you look pretty.
I think the price is reasonable and it is a good product for casual makeover. I think it looks cute.
Installation was a little difficult in positioning.
The drawback is that the LightBody of the car body gets small scratches at the installation pin if the positioning takes too much time and has to be redone.
Rather than putting it on and taking it off, it might be better to leave it on after putting it on.
View detail
Fits: HONDA FTR223, Others , SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER, HONDA MONKEY
good
Used for fz400
The texture is HURRICANE as it should be.
Position is generally as expected.
fz must be extended for Wire and Hose.
View detail
Fits: HONDA APE 100, HONDA GB250 CLUBMAN, HONDA APE 50, HONDA APE 50, SUZUKI GRASS TRACKER Big Boy, YAMAHA SR500, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E, SUZUKI GRASS TRACKER, Others , YAMAHA SR400, HONDA MONKEY, YAMAHA TW200, HONDA FTR223, HONDA FTR223
Caution when installing
It is an inexpensive product, and since it is made by a long-established manufacturer, there should be no problem with the quality of the handlebar.
Two requests for improvement.
(1) The paint is too soft and just a slight touch will cause wounds. (2) Extreme care must be taken when installing this product.
I would like the center mark to be engraved instead of Sticker, because Sticker is too hard and peels off easily.
View detail
There is a slight difference.
I wanted to lower the OEMMirror position on my PCX a bit, so I purchased this one with a similar design.
It is a slight difference, but the overall impression will be different.
Level with no complaints about the ease of viewing.
The type of installation is tightened with a cap bolt.
I know they are designed to protect pedestrians, but even the slightest shock would loosen them, so I tightened them up quite a bit.
View detail
Handlebar exchange
It looks very current.
It's like the fad that was back when I first started riding Harley.
View detail
Fits: KAWASAKI NINJA400 (2014-), KAWASAKI NINJA250R
Almost perfect
This is the only 'superbike kit' I could find for Ninja 400. Luckily, from Webike it's reasonably priced, given the low initial cost of the Ninja 400. The bike is said to have a relaxed riding position, as opposed to a sportier one in some other sport bikes, but for a shorter rider or an old dude like me a bit more upright riding position is a blessing. The kit contains all the hardware needed for installation, but like the website states, the instructions are only in Japanese. That means you must either have some idea how to work on bikes, or have a mechanic to install the kit for you. When removing old cables, tape an electrical wire on its end, pull the wire in its place, and then you can pull the new cable in place with the wire. That makes the job a lot easier. Right hand control cables (starter and engine stop switch) are a bit short after kit installation, so you would do best detaching the connector under the tank and re-routing the cables higher up in the frame for extra slack. Rest of the installation is pretty straight forward. Fit and finish of this kit is very good, well on par with the rest of the bike. The only complaint I have is about the throttle cables. The upper ends don't seem to be an exact match with the housing, so the throttle will be a bit stiffer to turn than originally. You can hear some scraping sound between parts when turning the throttle, and if you tighten the housing screws too much, the throttle won't return. I found a sweet spot where screws are tight enough, but there's still enough play for throttle tube to turn freely. All in all I'm pretty happy with this kit. Riding position is well improved. If Hurricane would see the trouble of creating installation instructions in other languages and fix the issues with the throttle cables I would give five stars. View detail
Discontinued?
This is a slightly different imprement from my impression of the product, but I hope it is helpful.
We inquired several times about the delivery date, but the response was that the delivery date was undecided.
I've been told that there is no stock or delivery date other than Webby's...
I had no choice but to buy a used one for the same price as a new one.
If you really want it, you might as well buy it when you see it.
I do Tandem only to the tiniest balls, but it is easier because they don't grab my body.
View detail
Fits: HONDA glom, HONDA glom
Grom installation
It is easier to drive, although you have to be careful about the angle of the Handlebar or it will hit the Cowl. View detail
it work very light and smooth
I bought Hurricane long throttle cable to replace the old on my Honda VFR800 VTEC 2003. Shipping time is a bit longer than 2 weeks after shipping. Hurricane throttle cable is Made in Japan, the cable is long enought to install on my bike, it work very light and smooth. View detail
mirrors
perfect for my bike. Looks better than stock. Thanks About quality and texture About the feeling of use Products to buy together Difficulty of installation Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasingAbout quality and texture About the feeling of use About Design About Size Chart Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasingAbout quality and texture About the feeling of use Products to buy together Difficulty of installation Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasing View detail
Position Comfort
The Handlebar on the DL1000 V-STROM650 felt a little far away, so I installed it.
After installation, the handlebar became a little closer to the hand, which made positioning much easier and touring more comfortable.
Cable, etc., only needed a little band, bracket, etc., positioning.
View detail
Rear Sets, OEMHigh seat, and Handlebar Spacer are required.
I am 178cm, but the riding posture of the NORMAL bike was like a motorbike converted to a MT bike, and I could not shift my weight properly on the Corner ring, so I had to ride it only for commuting to work.
After adding the Rear Sets, OEM High Seat for North America, and Handlebar Up Spacer, I was able to have a drumstick posture, and I was able to turn in a circle even on a mountain pass, making it twice as fun from touring to around town.
If you think it's not good enough, you can use the aboveQuantity:1 Set of 3-items is a must buy.
View detail
good quality, perfect fit
Bought these for dragstar 1100 classic. The cables look to be of good quality and fit my bike perfectly. Don't forget to lube the cables before installing them on the bike. View detail