Reviews
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), HONDA CBR1000RR, HONDA CBR929RRFire blade, SUZUKI GSX-R1000, SUZUKI GSX-R600, KAWASAKI ZX-10R, KAWASAKI ZXR400, KAWASAKI ZX-6RR, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA TZR250, HONDA RVF750, YAMAHA TZR250, HONDA RVF400, HONDA VTR1000SP, HONDA CBR954RRFire blade, HONDA RS250
Shallow angle
It came with a 10° Handlebar, which felt a bit tight, so I bought an 8° Handlebar.
Only drilling of the switch box is required, but I am satisfied because the position is relaxed and the front load is not lost.
View detail
WheelBalance
Used for Tire replacement. Black color would be nice. View detail
Essential Items when replacing Tire
[How is it used?
I use it every time I change a tire on my Racer YZF-R25.
In a race, the front wheel balance is especially important because of the speed range.
Since my vehicle has a slightly shaken wheel due to a fall, this is an even more essential item.
How was your experience with it?
I used to use Jay Trip's Weight, but this time I went with Battle factory because they had it in stock.
To be honest, it is just lead, so there is no good or bad, but Battle factory is Shiningly more Beauty to look at.
How did it compare to other products?
It is comparable to Jay Trip. If I had to say something, I would say how easy it is to peel off the adhesive side.
This is also difficult to remove from Battle factory, and even if you pry it off, the Sponge portion of the Double-sided Tape remains.
It's better than peeling off, so that's good.
I would also like to see a Black color since Coloring is only available in Silver.
I don't mind the Racer, but when I put it on my town car, it will stand out if the wheel is black.
[Points to note]
When attaching Weight to Wheel, be sure to degrease Wheel thoroughly before attaching.
Failure to degrease the adhesive part of Weight will weaken it, and it may peel off and fly away during driving.
I am lowering the Risk of skipping by dewaxing→pasting→Black adhesive Tape on top of the Weight.
I see that all the vehicles that run on Circuit are reinforced by taping on Weight.
View detail
The faster the Situation, the more important it is.
[How is it used?
I used it to replace the tires on my Racer motorcycle.
Was the one you received as per Image?
It is a weight, so it did not differ from Image.
It is surprisingly soft to the touch and can be bent to fit the curved surface of the Wheel.
Was the installation difficult?
Balancing the Wheel is tough without a Balancer.
If you don't have the environment to take the balance yourself, it is safer to let the store do it for you.
How was your experience with it?
The Balancer itself is designed to be attached with Double-sided Tape, but I put more Tape on top of the paste. When I tried to remove the tape when replacing it, it was very sticky, so I didn't feel like it would come off easily.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
one
It was hard to assemble it to the Handlebar But it is too hard I missed it again:I didn't know it was 1pc A simple explanation is needed View detail
Ideal for changing the length of the shift rod
I bought it because I wanted to change the length of the Shift rod when I changed the position of the pedal
To begin with, STREET TRIPLERS has a Quick shifter It will be Standard Equipment, but Babyface's Rear Sets have a The Shift rod that came with the replacement did not take into account the Shift Switch I would like to replace the Shift Rod with one that matches the Shift Switch on it I found a Shift rod made by the Battle factory
I don't think it was originally intended to be combined with other companies' products, but the Large body vehicle The Pillow ball on the Shift Pedal has an M6 thread diameter, so it can be installed There was no problem
Moreover, you can choose the length from 80mm to 300mm in increments of 10mm to match your vehicle's specifications You can also choose the length you want to order according to the spec. of your vehicle
It should have been ordered by the Manufacturer as Repair Parts This is the only product sold as a universal product There's only one, so you can save yourself the trouble of ordering
Personally, I trust the fact that it's made by the Battle Factory, a familiar name in road racing Factor
However, as you can see in the description, it is a product that only cut a screw hole in the hexagonal bar of Aluminum (see ROD's Center is cut-out, but …) is 1 pc2, It's a bit awkward to spend more than 5,000 yen, or 3,000 yen for a long rod Other companies' Shift rods are sold for around 1,500 yen, so if the length is right, you can buy a different one There are also cheaper products at
Also, since this is a function-first product, it is only available in the bare aluminum color Recently, the number of footpegs painted by Anodized is increasing, but Shift rod If your shifter is painted as well, you may find that the shifter rod is more noticeable as shown in the picture The original color of the Shift Rod was Black
View detail
It's normal
Personally, I don't like the plain old Bar End, so I used KIJIMA's But because I wanted to make the end shorter in combination with Grip, I installed it If old-fashioned Racer is preferred, it is Recommendation However, whether it is expensive View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R, HONDA CBR600F, HONDA VTR1000FVTR1000F FIRESTORM, HONDA CBR400RR
Moderately
Immediately after arrival, wearing. Although it is written in the explanation, since it is universal, the hole for the anti-rotation must be processed additionally, but it can be poured.
Handlebar itself is light, texture is not bad.
Since the hanging angle is different from the OEM, it comes into contact with Cowl, so adjustment of that side is necessary.
View detail
Fits: SUZUKI GSX-R600, SUZUKI GSX-R1000
It was not Bolt-on.
In reality, the dent under the photo (Shape to avoid other Bolt's head) However, it was not retired and it was connected.
Since it can not be helped, I figured out that I scraped the gorillor with a round file, but the material is durable.
View detail