Reviews
Good
Ideal for loosening sticking screws.
It is a Penetrating Driver, so if you tap it with a Hammer and make it bite firmly, it will not lick.
The tip also does not slip, so Torque can be applied firmly.
View detail
safety
Safe and easy to find the power source. When searching for a permanent power source from the vehicle's harness, the LEDs on the body light up to make it easy to locate. View detail
Really long!
This is a good tool to reach areas where you need a gripping screwdriver. The tip is serrated and holds screws well. Recomended. View detail
The best JIS screwdrivers
Ive bought a few different JIS screwdrivers over the years and these are some of the best. The Impacta device works well and the tips are well made and withstand the use. Great grips as well. My go to brand for screwdrivers for Japanese motorbike screws. View detail
watchman
I always buy this product.
It's expensive, but the tip is sturdy and fits the screw.
Very easy to use
We do have some thicker Grip products.
The force is easily applied when tightening, which can lead to overtorque.
I like this one just as much as the other one, which can be tightened just fine.
Grip has a distinctive smell, so tastes vary.
View detail
Convenient
The band that holds the 4-cylinder Throttle body in place is quite deep, so an ordinary driver cannot reach it. This product is inexpensive, yet accurate and easy to use because it is hard to lick the Screw. I bought other sizes because of its low price. View detail
I don't use it that much in Motorcycle, but it's handy to have.
I think it is the smallest ClipTool for use on a motorbike. I often use this product in my car, and it is very easy to use. View detail
Easy to use
[How is it used?
The size of the Fixing Screw of the Generator Cover is Large, so I purchased the No.3 number because the normal Phillips Screwdriver was almost tarnished.
Was the one you received as per Image?
As shown in the picture, it was bigger than I expected, but it was just right for my use.
How was your experience with it?
As described as a firm Fit to Mt. Screw, it was Firmly engaged and did not feel like it was going to lick at all.
I thought it was comfortable to hold and very easy to turn.
The hexagonal shaft makes it easy to apply Torque, and it is also used as a penetrating driver, so it is likely to be used more often in the future for maintenance of old cars.
[Points to note]
It is difficult to get a sense of size, but for the 1st pc Penetrating Driver, No.1 or No.2 is good.
I chose No.3 because the Screw mountain I use is a bit deep and wide.
How did it compare to other products?
I only had a Phillips Screwdriver, which I didn't know well at Homsen, but it is incomparably better than that.
The ease of use, such as the feeling of fitting snugly to Screw Mountain and the ease of gripping, is good for the price.
【Review】
It was easy to use, as it is a highly rated Driver.
For light maintenance, an inexpensive one would be fine, but for those who do heavy maintenance, it would be worthwhile to have one pc.
View detail
For removal of Air cleanerBox.
It was a Plus screw on the Air cleanerBox, so I bought it to turn there.
The Grip is also shaped for easy grasping and use.
I thought it might be a little expensive compared to another Manufacturer, such as Home center.
We chose KTC because it is a reliable tool that can be used for several years.
Minus is also a Quantity:I thought it was a Set and bought it together.
View detail
Easy to apply force
I bought this to replace the Driver because it was getting tired.
As KTC claims, it has a shape that makes it easy to apply force.
The cross-section is almost square, so I don't think there is any driver that can compare to this product when turning the screw with LargeTorque applied anyway.
On the other hand, once the screw is loosened, when you turn it round and round, it requires a hang to remove it at high speed because it is low geared due to its rectangular shape.
I have a lot of opportunities to turn a stuck Screw, so I wanted a Driver that could hang a LargeTorque anyway, and I like it.
Since it is a Penetrating Driver, it can be used by tapping it with Hammer.
I once beat GunGun to the point of destroying Driver, but I can still use it today without any damage.
The precision of the tip is also well done as only KTCBrand can do, and as long as you choose the right size, you will hardly lick it.
Also, since it is magnetized, it is less likely that the loosened Screw will fall off.
Because of its overall thickness and rigidity, it is difficult to access narrow gaps, but I use different drivers for the right places.
View detail
Compact
I was looking for a compact and small one to use in a small space, and this one looked good, so I bought it.
The size is a little larger than I expected, but the turning part is nice and usable.
View detail
I was able to use it conveniently with my 4mini below the waist Custom.
The Screw which fixes the StatorBase of your beloved car DAX is Size3 in Plus.
I think it is impossible for a normal Driver to loosen this one.
This time, I was able to remove it safely by using this product and Hammer which I bought separately.
Size3 is one sizeLarger than the regular Plus screw.
I don't think you can have an Exactly Driver very often.
If it is this product, it can be used as a normal driver if it is not beaten with Hammer.
I think it is a convenient product that has no loss to have 1 pc because it can be used.
View detail
For removal of Jet
[How is it used?
I used it to remove a Jet that had almost seized on the carburetor.
I didn't have the right size in my hand, so I chose this product with a flat tip on a thin shaft.
Was the one you received as per Image?
I chose the size 190mm in length which seems to be easy to use.
It might have been a bit long to use it on the carburetor, but I didn't have any problems with it.
How was your experience with it?
I was able to safely remove the Jet of the carburetor which I could not turn with the Precision Driver which I had.
It was easy to use, especially since Jet didn't lick it.
The Elastomer grip makes it easy to grip without slipping.
How did it compare to other products?
There are several drivers for the carburetor Jet, but I chose this product because it is quite expensive and has a mixed reputation.
I didn't actually use that one, but I didn't have a problem using it enough with this product.
【Review】
The feeling of use, accuracy, etc. were good because it was made by KTC.
Since the price is inexpensive, it was enough for me personally even if it was not the Driver for Jet.
Dasa, the unique YellowGreen color makes it easy to find instantly in your toolbox. (Lol)
View detail
Slotted screwdriver。
The tip is sharpened and used as a tapping tool. View detail
It depends on the location.
The size is delicate, so the place where it is used is limited. View detail
Subtle Size.
It's not the easiest Size to use, but it depends on where you are. View detail
A definite classic.
The cross section of the shaft is round because it is not designed for rough work, and therefore it slides and turns very well even if it is supported by hand.
This ball-shaped grip is easy to turn quickly and is a definite tool for light, twirling work.
Personally, I would recommend the ANEX electrician's tool if you want to do everything in one tool, even a little rough work.
ANEX shaft (Hexagonal cross section) It can be used to turn the tool on and off, which is helpful when you have a tougher screw than the ShockDriver.
Both of them are performance as a driver. (Bite, durability, etc.) is sufficient.
The VetuCell is the Grip shape that many people prefer, so many people will prefer this one.
I think it's better to use the one you like when you actually touch it.
View detail
It's for electricians, but Tough
This kind of standard is for VESSEL electric (Many manufacturers are copying it as it is) I think, but after using both, my honest impression is that it's hard to choose between the two. I prefer this one.
The grip with the groove of Beth Cell Type might be a little better to grip with an oil hand, but this one which looks smooth also has a texturing pattern and unexpectedly does not slide so much.
The grip is triangular, so it's easy to turn quickly, and if you need more power, the hexagonal driver shaft allows you to use a tool to turn it.
Heads with Plus notation are Material:Although it is plastic, it is quite sturdy, and although it is necessary to take it easy compared with Penetrating Driver, it is possible to use it enough even if you beat it. PlusMark of the identification doesn't disappear easily either.
If you want to use one to handle everything from fast turning to tooling up and turning with LargeTorque, this is the one for you.
View detail
Very short driver
First for carburetor adjustment (Minus) I bought it because I thought it was convenient for
The overall length of the screwdriver is shorter than that of a standard Stubby Screwdriver, so it is the only choice for tight spaces.
Also, the Clip of Cowl on the underside of the car body (Plus head) You can apply it straight without worrying about the clearance with the ground when you remove the
By the way, Minus side can be used conveniently when prying Clip which is hard to come off.
This small size allows you to use it interchangeably, so you can have both Plus and Minus, and it fits in your toolbox compactly.
View detail
This is the only way to do it.
I bought this exclusively for removing the carburetorIndicator from my 4 shot Engine.
There is a hole in the Aluminum Frame for the Driver, and with a fairly long Shank Driver, you can loosen the screw in the Insulator band.
In reality, the 450mm Shank is a little too long, but it gave us plenty of room to work with.
The grip is long enough to fit the overall length of the machine, so you can turn it with both hands without worrying about turning it with a lot of force.
The tip of the tool is a little bit special shape, which is long in one direction of Plus groove, but it can turn a normal Plus screw without anxiety. As the name suggests, Shank is a square shaft, so you can put the tool on it and turn it if you want to.
View detail