Reviews
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
The footrest for Monkey
I bought a footrest for a Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is what you need. It came up without any problems, the installation is fast and easy. The price and quality are minimal. I recommend it to everyone. I bought a footrest for the Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is just right. Fits without problems, installation is quick and easy. Minimum price and quality are high. I recommend to all. View detail
![[Option Parts]ReplacementTip](https://img.webike-cdn.net/catalogue/images/55193/ze56_8929_TS.jpg)
80mm for MOTARD in WR
I put it on my WR250R MOTARD, but the height of the STANDIncluded Tip is too low and the motorcycle falls over a lot. It would have been better if the height of the tip could be selected in STANDIncluded Parts:. View detail
Forged aluminum is very high strength
It's just STAND, so the only change is that it makes me feel a little better. I put it on my WR250R MOTARD, but the attached tip is too low, so I bought a 55mm tip from Option Parts and use it. I bought a 55mm tip from Option Parts because I didn't want the motorcycle to fall down too much. It would have been better if I could choose the tip height. View detail
Fits: SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100
Very convenient
The side stand is essential for scooters, and if the installation is done according to the instruction manual, it is not particularly difficult and anyone can install it.
It has become extremely convenient!
View detail
A little too short?
Since the Lowdown Kit was installed at the same time as the car was delivered, the car body was standing up, so we had to be careful where we parked the car and sometimes could not pay the side stand depending on the road surface conditions. After the replacement, it leans quite a bit and I have a sense of security, but if it were 10mm longer, it would lean too much. View detail
Cutting off the Main Cause of Failure
I have a JumpCoupler that I made by myself, but I wasted the cost of 3.500 for one jump coupler, so it would be better to buy one. It's a WaterproofCoupler, so it's safe from now on! View detail
Stability is improved.
When I loaded the AA04 with luggage, it seemed to fall over when I hung the Side Stand on it, and I was worried about its stability, so I installed it.
The product itself is heavy and solidly built, so durability is not a problem.
Installation takes about 10 minutes if you have the right tools.
View detail
Rather, Parts that cure the defects of CT125
The completely unreliable NORMAL Side Stand is changed to a reliable Large Stand.
Before the replacement, it was unreliable with nothing on it.
Installing a Box on the Rear is already on the verge of mocking up.
After replacement, it is so stable that you don't feel the need to add STAND.
The STAND, which was originally squishy, is now tightly
(Endurance does not recommend it) in a STAND out state.
Stable when standing on footpeg
It should be this way from the beginning.
Parts to cure CT125 defects
When replaced, the body of the car is more upright than before.
Handlebar must be turned off to Left to be stable.
Become better at ground under Left than horizontal.
Instruction manual not attached Download required
No mention of pre-installation preparation Unfriendly
View detail
Round and round and round and round … I was in danger of dropping out.
The ReplacementTip (the part that lands on the ground) came loose right away, even though I tightened it! 。 A friend of mine installed it on his new CRF250L vehicle, but it was loose.
I stopped using Bolt of Included Parts:, changed to slightly longer Bolt, inserted Flat Washer→Spring washer→Flat Washer, and tightened it with Bolt, and it did not loosen.
View detail
No longer MC51's standard Custom
It is not used in Short Stand only. It is originally intended to be used in LowdownSpec. and is too tilted in NORMAL state.
The company's for PCXSide Stand boats. The company's for PCXSide Stand boat (EL505K1YA1) The length and angle you are looking for can be achieved by additionally mounting the Unfortunately, there is no board for MC51. If you want to use these together, it is recommended. When replacing, it is best to think in advance how you will pull the Spring.
View detail
I had to remove a lot of stuff.
I had to remove the Shift Pedal, Sprocket Cover, and Pivot Collar to get it off.
Once removed, the rest is easy.
I have a ZETA Side StandExtender, which is a special product for JA65, and there was no interference with the Center Stand, which I was worried about.
View detail
It's insanely good.
I was in a state of yajirobe with just a light push when I put my luggage in the RearBOX, but thanks to this Bracket, I am FirmlyHold ?.
I was worried about what kind of product it would be, but it is a very thick, hard steel, firmly welded, and I had no concerns about its strength from the looks of it. I was not worried about the strength of the product.
The work is easy if you are only careful when installing the stand switch.
View detail
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
Easy to use.
[How is it used?
STAND was purchased before the car was delivered because it was difficult to get it out,
I installed it immediately.
Was the one you received as per Image?
It was as Image in the picture.
Was the installation difficult?
It was easy to replace with Wrench.
Locktite is applied to prevent loosening.
How was your experience with it?
The Hook is in view even when straddled,
It is easy to STAND.
[Included Parts:were they on?
There was a Handling Instruction Manual.
[Was there anything that disappointed you?
None in particular.
View detail
![[Option Parts]ReplacementTip](https://img.webike-cdn.net/catalogue/images/55193/ze56_8919_TS.jpg)
ZETA ReplacementTip
Purchased to fine tune the height of the Side Stand. I am a little worried when parking the car because the body of the car is a bit laid down, but so far it is Large and sturdy. The length is fixed, so I hope there will be a product that allows free size adjustment. View detail
Zita Forged AluminumKick Stand
I installed it on my crf250lmd47 to make it look cool and solid. View detail
Fits: DUCATI SCRAMBLER 1100, DUCATI MONSTER 797 Plus, DUCATI MONSTER 797
AELLA
Tilt when parking has been improved:?? View detail
I checked for conformity and it didn't.
Lowdown on FXDC.
The 1inShort Stand of a certain U.S. Brand has been Rusted so much that we decided to replace it with this one.
If it is made in Japan (including overseas production + quality control by Japanese companies), it is safe in many ways, and there is hope that maybe it will not rust so easily.
Now assembly.
Remove the old STAND, remove the Block for fixing the STAND to the Frame and the parts for fixing from the old STAND, attach the Block to this product and the parts for fixing... it won't fit!
The STAND side is slightly thicker and does not pass through the hole.
I thought I had made a mistake. I was surprised, but I didn't make a mistake.
Slightly thicker, this thickness, perhaps the thickness of Plating?
Thick plating is welcome for Large, but the assembly part must be made with that in mind!
It took about an hour of extra time, but we were able to assemble it safely.
Nowadays, even CHINA has better accuracy. 。 It is impossible.
I wonder what people who can't afford to cut down would do in this situation.
I've already removed the old one, and the mental burden of putting it back in is LARGE.
Harley is still Jack-up and waiting for delivery for return and exchange? There's no guarantee that the replacement will fit properly.
Incidentally, the quality of the finish of the product itself is not as good as that of a certain U.S. product.
But I thought it was totally OK for such a low price before assembling it.
If the quality is not normally assembled, even at this price. Ok." It will not be a
If this doesn't produce Rust for a long period of time, it might make up for this annoyance....
View detail
Nagano and Gifu prefectures have quite a few unpaved parking lots.
I could not tell the large size from the product photo, but when I saw it in person, it was a large enough size to be used for practical purposes. As you can see in the picture, it is almost the same size as the iPhoneSE. It would be better if the material was rubber. View detail
Not used
When disembarking crf250l md47 with a full load of luggage, the softness of the suspension makes it difficult to disembark in a vertical position.
I bought this product 25mm shorter, but now it seems to fall over when it is empty, not when it is loaded, but when it is tilted.
I did not use it, so I returned it to OEM. By the way, I also adjusted the suspension pre-road and made it stiffer.
There is a way to make Minus15mm by adding 10mmWasher, but it is still inclined,
I'm not sure about full/empty loads, so I'm under the impression that I shouldn't have bought it.
I think the product is robust and good.
View detail
Fits: HONDA MONKEY, HONDA DAX, HONDA GORILLA
Kick Stand
The prefect way to add a kick stand to a honda monkey with rear sets, attaches to all 4 bolts under the engine and keeps it looking stock View detail