Reviews
in a secluded place
Convenient for use in secluded places.
It is quite useful with different lengths.
View detail
Extension
It is used in a secluded place.
It is convenient to have several types with different lengths for different uses.
Combined with the Compact Ratchet, it doesn't take up much space in an in-vehicle tool.
View detail
Length change
Convenient for use in secluded places.
Combined with the Compact Ratchet, it doesn't take up much space in an in-vehicle tool.
View detail
For servicing and maintenance use
Affordable price, so much Quantity:Set, making it convenient to use and use.
The Level is sufficient for everyday use and is fine in use.
View detail
For Maintenance
This is a purchase for use in Socket extension for use in Maintenance.
The price is not too expensive, and it is convenient to use three different lengths.
View detail
More than the price
Tools are required to be precise, and I think SK11 has a lot of good products for the price. View detail
Small, Compact
I wanted a compact, small-sized product that could be used as an in-vehicle tool, so I purchased this one.
It is quite small. Large enough not to get in the way, tough to apply strong force, but usable enough.
It is a useful tool, although it is difficult to convert the tightening direction due to its small size. The selling price is a little high, though.
View detail
Easy-to-use tools
Convenient for tight spaces where a Socket wrench will not fit.
I recommend it because the quality is not bad for the low price.
View detail
Compact
I purchased the Ratchet because I thought it would be convenient and easy to use for in-vehicle use and for small occasions.
It is really small. The small size does not allow for a lot of force to be applied.
High selling price (The price is going up.) It is a pity.
View detail
products with advantages and disadvantages
This is a swiveling Type, which can be fixed, but it comes off easily.
You should also buy a regular T-type Handlebar.
View detail
Easy to put effort into.
I purchased this product to install a Hepco/Becker Engine Guard.
Since the SV650 has a frame fixed by the engine, it requires a lot of torque, so we used a long handlebar.
As a result, I was able to remove it with ease.
The length is nice and fits in the e-value Tools Set.
View detail
Necessary and sufficient performance
[How is it used?
It is useful for loosening axle shafts and steering nuts on motorcycles.
It can also be used to replace Tire on cars.
Was the one you received as per Image?
It was just as Image.
I appreciate that SK11 has a pretty good selection of products with excellent Cost performance.
There are some spec. for reduction in cost, such as no holes in the handles and no Knurl processing to prevent slipping, but I think it is sufficient.
I also use a Torque wrench to hang Torque.
How was your experience with it?
It is quite effective for Bolts and Nuts that do not loosen or have high Torque applied to them.
Basically, it is used for bolt and nut of the undercarriage that is stuck, but it is easy to work with thanks to its length.
Socket tools are mainly aligned with a 3/8 insertion angle, but for those that are unlikely to come loose, 1/2Socket is prepared in advance and used.
How did it compare to other products?
The Spinner Handlebar of this length made by other well-known manufacturers is quite pricey, so it's nice to know that it's cosmetically sound.
View detail
Convenient Socket adapter
[How is it used?
Used for tightening at 40N-m when cleaning and installing Caliper on XJR400R.
I have two Torque wrench, one for ~25N-m and the other for 40-140N-m, but one of them has a 12.7mm insertion angle. (1/2-inches) and the other is 9.5mm (3/8Inch) The Brembo caliper mount bolt is 12mm, but the 12mm socket I have is 9.5mm. (3/8Inch) So I needed a conversion and bought this one.
Was the one you received as per Image?
It was just as Image.
I think you can find them at Home center, but I'm glad to know that they are not available at small places and that it is cheaper to buy them here.
How was your experience with it?
Thanks to this, we were able to tighten it with a solid Torque.
I want to make sure that the Brake area is secure because if anything happens to the Brake area, it will be Large strange.
How did it compare to other products?
I have seen other manufacturers' products, but I think this one is the cheapest and has the best cost performance.
View detail
Special Tool in a sense
I had a slightly smaller long driver in the carburetor setting, so I used that, but it was not good enough.
(15cm for No.1Driver, 30cm for No.2Driver)
ThrowAdjust Screw (PilotAdjust Screw) I was looking for a slotted screwdriver for the head of the No.1 driver and one that is at least 20 cm long.
Then I found this product and bought it, thinking it would probably be Large sturdy since it is 25cm long.
Since we are using PWK for APE, all Adjust Screws are on the Left Side and OEMEngine Layout, but the carburetor is installed diagonally Right, so unfortunately it is shadowed by the Frame, I thought it would be better to change the way of thinking and look for a tool that can be used for a long and thin time.
Surprisingly, it was easy to use and set up, and I'm glad I was able to save more time than before.
View detail
Easy to put effort into.
I purchased this product to install a Pepco Becker Engine Guard.
Since the SV650 has a frame fixed by the engine, it requires a lot of torque, so we used a long handlebar.
As a result, we were able to remove it with ease.
The length is good.
It fits into e-value's Tools Set.
View detail
This is handy.
Mast is especially useful for Scooter and other hard-to-access structures.
Magnet does a good job.
One drawback is that Material:I had a hard time understanding the instructions on how to remove the plastic tag-like thing because the text and illustrations were too small. In fact, it was easier to replace the plug.
View detail
Mistook it for a hexagon and bought it.
[How is it used?
I bought this to loosen the Driven Sprocket on my XJR400R.
Was the one you received as per Image?
I did not read the product specs carefully and bought it thinking it was a hexagon, but it was a dodecagon.
It is not impossible to use a 12-square, but the way the Torque is applied changes from a 6-square to a 12-square, and it is difficult to use in places where considerable force is required.
How was your experience with it?
I still could not loosen the force well.
This caused a little damage to the Nut and I failed. This was my own fault, though, so I had no choice.
The product is inexpensive and easy to use.
[Points to note]
Read the product Spec. carefully!
It makes me sad when I buy tools I don't use lol.
How did it compare to other products?
I later purchased a similarly priced hexagonal VERSION.
I think the quality of this product is slightly higher.
View detail
Robust tool.
[How is it used?
I purchased this to remove the Oil Inspection Bolt on the lower side of the Engine on my CB1100.
Was the one you received as per Image?
It is a robust tool that does not seem to break down in the slightest.
How was your experience with it?
I was prepared to remove the bolt because it was the bolt of the engine part of a Large Motorcycle, but it came off so easily with this tool that I was surprised.
[Points to note]
If the Engine Guard or something else interferes, it is a hassle, but it is necessary to remove everything.
How did it compare to other products?
I don't know about other companies' products, but a tool with a sense of security is the best because it is a part that cannot be recovered if it is licked.
▼Although rarely used, it is a good idea to have it on hand.
View detail
durable tool
I bought this SK11 25mm screwdriver bit set from webike. The set contains 10 tools. The tools are very detailed and durable. The surface has a micro-coating but is very thin, so the screw accuracy is very high, and it is not easy to screw the screw. A storage seat is attached for easy storage after use. -------------------------------------------------- -------- I bought this SK11 25mm upper set at Webike. The suit contains 10 tools. The tools are very detailed and durable. The surface has a micro -coating but thin, so the screw accuracy is very high. It is not easy Comes with storage seats for easy use. Powered by Google Translator View detail
It's being overworked hard!!!!
I have polished the fins of the Radiator and have used it extensively over the years, but it is still in good working order.
Not a lot of shedding, and for this low price, I can't complain!
Very Recommendation!!!!
View detail