Reviews
Carrier
It covers Bobber's problem, loading capacity.
Now you can go on a sleepover Touring.
The texture is good and sturdy.
Recommendation to Bobber riders.
I think the installation is easy since it is Bolt On, but I have asked my dealer to do it for me…
View detail
Fits: その他 Vehicles equipped with Hepco & Becker top case holder *Except for Easy Rack and Pipe type, その他 Vehicles equipped with Hepco & Becker top case holder *Except for Easy Rack and Pipe type
Hang is required to open and close
First of all, it is wide horizontally, so Helmet cannot fit in it.
The waterproof rubber is tearing off over time, but this has never happened with GIVI, so I would have to say that GIVI has the better quality. It requires a hang to open and close.
View detail
good for my G310GS
it is a perfect product for G310Gs,it is very enought to protcet my motocycle and it looks is so cool,i suggest everyone to by this View detail
Drill Required
[How is it used?
yzf−r6 (with speedrack) Used for about 3 days in
Was the one you received as per Image?
As per Image
How was your experience with it?
I thought it was convenient because once set up, all I had to do was one-touch.
[Points to note]
The easy-lock receiver must be attached to the BagBody, which requires drilling a hole in the bottom surface with a drill, and if the positioning of the receiver fails, it is irreversible.
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
HandyDrill
View detail
The good stuff is good.
It's 40 liters, so there's plenty of room to load it up.
Opening and closing was easy.
It will last a long time.
View detail
Rather than making your own.
When I installed C-BOW and StreetCase on my BMW R nineT, the bag interferes with the legs of the Tandem rider, and I can only hang my heels on the Tandem Footpeg.
I was thinking of making my own with aluminum blocketc., but WebikePoint seemed to cover half of the case, so I bought it.
There are no problems with installation. Depending on the direction of installation, it can be moved forward or backward.
With the STREETCase installed, the interference with the Tandem rider's legs is almost gone, and I can now put my feet on the footpegs.
However, in the case of the Ninety, when the Case is installed, the safety standards for the position of the Blinker will not apply. "Visible from anywhere within a range of 20 degrees inward and 80 degrees outward of the winker." So, I will have to relocate the rear blinker.... (No problem if Case is not installed).
View detail
Fits: BMW RnineT Racer, BMW RnineT Pure, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT
Good thing I left it on.
Since I had the dealer install it when I purchased the vehicle, I won't give an evaluation of the installability.
First, the appearance.
The car has a lot of black parts including the frame, and the black engine guard grows out of the black frame, so it doesn't feel unnatural even if it is covered with a silver colored Hend Cover.
And the important thing is that the protection is godly!
Quantity of so-called "standing moss" on a public road:Pair (for Left and Right) I defeated each of them once, and almost all of them had no damage except for the Engine Guard.
(This is only our experience. The results may have been different depending on how and where you fell)
When I tipped it to the Right, I had the Tandem Footpeg out, so the Wound was in the tip of the footpeg. If I had stored it, it would not have grounded.
Quantity in low position:Pair (for Left and Right) The end of the handlebar extends to the top of the handlebar, so the end of the handlebar won't be grounded by a mishap.
Therefore, it is easy to wake them up.
For the repair, I roughly dipped the paper file in it, blended it in, and painted it black with Touch pan.
It is recommended to wear it if you are not sure about your footing or leg strength.
View detail
Fits: BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT
Tandem Necessities
I had it installed by a dealer when I took delivery of my car, so I won't evaluate the installation.
I installed it because my wife and I often go out with Tandem.
As for the appearance, I think it is simple and does not stand out too much.
For a simple Neo-Class car like the Ninety, it would be better not to add extravagant, but for the convenience of the Tandem, I think this minimalist product is the way to go.
I've never tried riding in the back seat myself, but according to my wife "The height and thickness are good for grabbing." He said.
It also comes in handy as a temporary handhold when handling or hanging the maintenance stand.
If you want to load cargo when you tandem, you can use their Carrier. (Top case holder/PipeType) You can also consider the following.
View detail
This is my lifeline.
The vehicle weighs more than 100kg heavier than conventional motorcycles, which may cause the vehicle to bog down at low speeds or when handling it by hand.
We're about to reach double digits, and thanks to these Parts, Cowl is almost scratch free!
Not even my leg got caught! It sends a thin chill down my spine to think of how much damage I would have suffered without it.
As you can see, I can't protect the exhaust system's SmallWound, clutch pedal, rear brake pedal, etc.
There was no Damage until it affected self-running.
I think most people who buy this motorcycle will enjoy long distance touring.
When you are experiencing a significant increase and fatigue, you may find yourself standing up unexpectedly.
I think there is.
The scary thing about long-distance touring is that you may not be able to drive yourself.
You may want to consider buying one to lower your Damage.
I'm not sure what would happen if I fell while driving;
View detail
Fits: Others Hepco & Becker Top case holder mounted car
It's as bad as Explorer. W
1:How did you buy it?
This is the first time I've seen this product. I've been using their Explorer for 9 years now, but the cracks in the plastic frame are steadily progressing. I've been using it for 9 years by reinforcing it and waterproofing it, but the cracks in the plastic frame have been progressing steadily, and even if I re-cast the Rivet or added a reinforcing frame, it would still fall down. I had no choice but to replace it.
To be honest, I was tired of HEPCO's products, but on a certain site However, one of the sites was selling Gobi at a low price as a stock clearance, and I was able to use the mount. ALLMaterial:I bought it thinking that since it was Plastic, it wouldn't be like Explorer (I was naive). I bought it thinking that since it was plastic, it would not be like Explorer (I was naive).
2:Appearance
The color of the black part is also Color.:Unpainted. I bought the DELUXE with Silver lines, but again, it's not resin plate or anything like that, it's just Sealw.
The resin is generally flexible, but the GIVI feels softer. This is a concern when operating a single-cylinder motorcycle with a lot of vibration.
3:Capacity
The inside of the box is double-layered, including the lid, so you can imagine a cooler box without Heat Insulating Material. The lid is also double-layered, so you can only put in smaller items than the large size of the box, and I'm afraid that the heads of the Bolt and Rivet might damage the Helmet and Shield.
The overall thickness of the product gives it a certain rigidity even with the lid open.
4:The problem (here's the main point)
? Fixing method is messy & lax.
(Photo 1) This is the fixed part of the front side of Case, and there is a gap of about 2mm in the area circled by the red line.
There is no longitudinal rattle in the new condition because the Mount Pipe and Case are tightly connected in the area surrounded by the yellow line, but there is a high possibility of rattling due to the distortion and crushing of the Panel over time.
(Photo 2) I attached a 3mm thick Rubber Seat to the Case side to make it stick.
Arai SZ−RAM4(XL) XL) does not fit
(Photo 3 & 4) I didn't check it beforehand, but I thought it was too much for 42L capacity... orz
It's a pitfall of the double structure. I'm going to try to solve this problem by modifying the lid side, because the magic field increase is essential for HEPCOBrand.
? The retractable shaft is not a hinge, just a plastic platew
(Photo 5) It's been a short time since I bought it, so I can't say it's an endurance test, but it's already gone white after about 10 times of opening and closing. What was I thinking?
Well, if this place looks like it's about to be torn to shreds, I'll go to the home-centre and use Material.:I'm going to buy some stainless steel hinges and install them. It seems that HEPCO's company policy is to let users do DIY without question (smiles).
5:General Comments
HEPCO & Co. BECKER is a company that destroys the image of Germany as a country of craftsmanship and quality products. It's a very good company. If you are going to buy a new box, you should buy GIVI no matter what.
I would also buy a GIVI without hesitation if there is a Top & Pannier case mount available for my motorcycle.
View detail
It is easy to install.
It was an easy-to-install tank bag.
It has a waterproof specification, so you can use it with peace of mind.
View detail
Fits: SUZUKI V-Strom650, SUZUKI SV650S, SUZUKI SV650S, SUZUKI SV650, SUZUKI SV650, SUZUKI SV1000S, SUZUKI SV1000, SUZUKI SFV650 Gladius, SUZUKI GSX-S750, SUZUKI GSX-S125, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R600, SUZUKI GSX-R125, SUZUKI GSX-R1000R, SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI GSR750, SUZUKI GSR600, SUZUKI GSF1250S Bandit
good
It's easy to install, and I recommend it because it's specific to your car model and easy to use. View detail
A strong ally for solo travelers
The Tandem seat is a replacement for the Carrier, but I think it will be a strong ally for those who go solo camping. I loaded the Enduris Tan Drum bag Size XL on top of this extended plate and attached a SoftSaddle Bag to it for camping. I used a locking strap and a bar to prevent the Saddle Bag from getting caught in the bag, and I think the bag was very stable. View detail
Fits: YAMAHA MT-07
A quick turnaround?
It's really convenient for Solo camping. Just remove the Tandem seat and replace it with a large cargo bed. It is stable even if you put XL on it. The price is Neck, but if you go camping in 07, you can't leave it. View detail
Fits: BMW RnineT Racer, BMW RnineT Pure, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure, BMW RnineT
2021 rninet.
I wasn't sure if I could install it on my '21 rninet, but I did.
Compact, discreet and solid compared to OEM.
I think it is better to do the installation work by two people as much as possible.
You will need someone to hold the Wrench on the One Side when you tighten the Bolt at the top.
You will also need a screw lock and a T55 Torque that can be removed.
Apply a small amount to the tightening bolt at the bottom and tighten, as the vibration may loosen the bolt.
I installed it by myself, but it was Large strange not to put Wound on Engine etc.
View detail
Fits: BMW R1200GSLC, BMW R1250GS, BMW R1200GS LC Liquid Cooling, BMW R1250GS
Robust product.
Installation on the R12000GS 2018:.
It takes about 2 hours to install by following the manual. The point to note is that you should not tighten some screws until all screws are temporarily fixed as described in the manual.
Protection.
I have the Engine Guard so it may be less likely to damage the tank but I have it on for insurance purposes.
By the way, there is the after that protected me when I fell on the Right Side.
Color:.
I chose Black, but Silveretc. might be better for the scratch.
View detail
Fits: YAMAHA MT-09, YAMAHA Tracer9, YAMAHA Tracer9 GT, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA Tracer 9 GT, YAMAHA Tracer 9, YAMAHA XSR900
Safe parking in gravel parking lots, etc.
If it is STAND of NORMAL, there is a fear that it will fall down in the parking lot of gravel. Because it is troublesome to look for a stone every time, I bought this. Because there was an instruction of the screw lock agent (medium strength) in Instruction Manual, I applied it and tightened it.
After the Stand End is installed, the car body will be raised lightly, but it is almost the level that is not bothered. I used to have HEPCO Stand End on another car, but it didn't fall down.
It's quite safe and I recommend it.
The tools you need are 3mm hex Wrench and Screw locker.
If you are used to raising the vehicle, you can do it from the left side by yourself, but if you are not sure, you can do it with two people or with maintenanceSTAND.
It is necessary to buy a special one for 21MODEL.
View detail
I installed the Engine Guard and took it down. GSX-S125]
https://youtu.be/VqFreRzr1to
Engine Guard installed:https://amzn.to/3sWRcNO
Hepco & Becker I installed Motorcycle's Engine Guard for the first time because I was afraid of tipping over.
This is a husband and wife Moto blog.
Because my wife wants to ride GSX-125, I installed it by the fall of the day when I ride it by moped 2 class Touring someday, and the countermeasure against a standing fall.
It was my first Custom and it works. I recommend it.
View detail
It's a good product, but Included Parts:is not good at all.
We recommend that you purchase only after you understand that there is a possibility of error in imported products.
You should do a good inspection of Included Parts:!
The hole dimensions for the collar that attaches the Crash Pad were wrong, it originally needed 11Φ and a collar, but it had a 9Φ collar.
After I contacted them, I thought I received the correct color, but I received one that was missing the dimensions of the color.
It is possible to install, but the height of the collar is not enough, so I am worried about the lack of strength because it is different from the original spec.
I understand that you don't do your own inspection on imported products, but I would like you to at least check the dimensions of the colors you send as replacements.
View detail
Fits: HONDA Forza 750, HONDA Crosstourer, HONDA X-ADV, HONDA NC750X, HONDA NC750DCT
It is a solid making
I installed it on my NC750X's unreliable Side Stand. The slope of the stand also rises slightly and it is easy to handle. View detail