Reviews
stability
The L4 is the shortest type of L4 and the L2 is the longest type of L4. I chose the L4 length short type.
The actualQuantity:The L2 would have interfered with it. I recommend that you check with your current vehicle. The plastic of the holder is thick and hard, so it can be used for a long time without any wear. I also have a V-brace for other motorcycles, but I like the fact that I can use the V-brace for other vehicles just by replacing the receiver.
View detail
RearShort Stand and Quantity:Buy Set
Quantity when you purchase J-TRIP's Short Stand.:I bought a set
This product is shortened so that the rear hook does not get caught on the axle shaft when removing and installing the rear tire.
For those who do not remove and install the rear tire, the V-shaped receptor (V-Shaped Receptor Set 1) of the conventional model is available. (Part No. JT-107V1) would be more stable.
In addition, there is a projection at the bottom of the Stand Hook, and by using a helping Rubber (JT-107V-R1), STAND-UP can be done safely without using the FrontWheel chocketc.
(It is recommended to lock the front brake when STAND-UP, Brake lever lock20 (JT-1042B) is useful.)
View detail
VHook for Hook bolt is no longer available.
Hook bolt ran out and I bought it. View detail
Fits: DUCATI Panigale 1199/1098(rear)/1198/STREETFIGHTER1198/Deer Bell MULTISTRADA 1000DS1200 MONSTER S21200/Setc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc., DUCATI Panigale 1199/1098(rear)/1198/Streetfighter 1198/Diavel Multistrada 1200 Monster 1200/S etc.
Short and unsettling, but functional enough.
[How is it used?
For home maintenance and custom
Was the one you received as per Image?
As per Image
How was your experience with it?
Shaft is short and I'm afraid it will fall out.
[Points to note]
Nothing in particular, as long as it fits the diameter of your car model.
How did it compare to other products?
This price for one Shaft seems high, but I have no other choice.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
J-TRIP's Helpful Rubber
I have to admit that this is very convenient for me to use the VHook Maintenance Stand alone in a small space, just like the Receptor Set for Beginner! (?) I'm sure they could use it!
I wish I had bought this from the beginning because I scratched the Swing Arm by inserting it at a slight angle without using this…
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Rubber cover comes off quickly
Rubber cover comes off easily. It was gone before I knew it.
The comfort is perfect, and I think every ZrX rider should have one, including J-TRIP's STAND.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Definitely!
It is indeed a ZrX exclusive product!
You can use it at a good height.
This will be for j-trip Wide Type only.
It cannot be given in a regular Short low ler.
Take care!
View detail
A classic?
I used it on a SEA BASS STAND, probably an OEM SEA BASS from J-TRIP that I purchased over 10 years ago.
I used to use a Swing Arm with a receiver on the Hook.
I bought a Ducati MONSTER400, so I bought this one too.
I could not find any Bolt on MONSTER400 that would attach a receiver to the Swing Arm.
Installation is simply a matter of replacing the Hook that was previously attached.
The Rubber seems thick and rigid enough to hang STAND with confidence.
I don't have a Spec. because I'm Firmly, but it would be nice if the price was a little lower.
Well, once you buy it, you can use it for more than 10 years.
View detail
Use at your own risk.
I bought a reverse attachment for the Rebel 1100 and used it, but the attachment on the Sprocket side did not fit properly and the tires did not rotate properly. I was told that if I put this Attachment for 250 or 500 on the Left Side and STAND-UP, it would solve the Stress problem;
I have not had a chance to try it yet, but I purchased it with a light feeling that if it does not work, I can just use the reverse Attachment.
The product is JTrip, so you can be sure of it.
I am satisfied with the Large change because the shipping was promptly done by WeBig.
View detail
![[Repair Parts] Type U Clamp Attachment](https://img.webike-cdn.net/catalogue/images/109969/29982_TS.jpg)
damage
As you can see in the photo, the spring and functioning part of the component was damaged from the start.
I assume it is fabricated by cutting from a board.
If it is to be used as a spring, I think it needs to be heat-treated, but I guess it hasn't been.
There are welding areas nearby, so the heat from the welding may have an effect.
I think it's a product with a high breakage rate.
View detail
Defective item
When I looked at the product sent to me, the spring part was damaged as shown in the picture.
I assume the parts were cut from sheet metal.
If they were to function as springs, they would need to be heat-treated or something, but I guess they haven't done that.
The heat from the welds may have an effect, and I think the product has a high defect rate.
As for DAYTONA's STAND, the front stand has recently been voluntarily recalled.
I don't think they are made in-house, but as long as they are sold, DAYTONA needs to take responsibility for quality control.
View detail
Designated items sold separately.
As per Title, it was a Manufacturer specified product of the RearMini stand prepared for the Z125PRO, and when I checked it when I purchased it, I always have the impression that it has a solid and sturdy finish.
Package. It's not slippery." It was! It is true that it is not slippery, but there was a case that it slipped a little in the initial stage of purchase due to the oil content from the compatibility with the paint of Z's Swing Arm or from the side work.
The resin of the L-receiving part, which is often a problem in overseas products, is welded with a thick urethane-like material, and there seems to be no problem with durability or aggressiveness to the Swing Armetc.
The rotation of the L-supporting part is also light, and when lifting the swing arm, simply place it horizontally on the car body and it will be attached to the swing arm. The stability of the Swing Arm is more than just the swing arm on the L-support, and the work can be done with a sense of stability and security.
As mentioned in Manufacturer's comment, we need to pay attention to the slippage caused by oil in the lower part of the Swing Arm, and now we always clean and wipe it off thoroughly before using it.
View detail
Use L4 for medium-sized vehicles.
The L4 can be used on a Large for Vehicle, but it sticks out a little more than the width of the Swing Arm, so I had to use it without interfering with the LimitSprocket. It was safer to purchase L4 for medium size vehicles. View detail
Either is required
Either L- or V-shaped receptacles are required View detail
![[Repair/Option Parts]Repair item Adapter for Front stand2](https://img.webike-cdn.net/catalogue/images/96580/25301_TS.jpg)
Front stand is now available for ZX-6R.
What made you decide to buy?
The Kawasaki NINJAZX-6R can be STAND-UP with a 27mm Attachment. However, the for KAWASAKI Attachment is a separate purchase unless you purchase the for KAWASAKI Front stand. The price is reasonable, so I purchased it.
[Others]
I was using a certain imported tool front stand with GROM first, but the attached attachment was 24mm, which is the largest size. It would be a waste to replace it just because I can't use it on my ZX-6R … buying another one would be a waste of space …." So I searched and found several 27mm Attachments that could be used for certain imported tools. Among them, I chose an affordable DAYTONA product. This will make the troublesome maintenance around the CFC easier.
Remarks.
DAYTONA27mm Attachment is the height and insert of a certain imported tool (13mm) However, DAYTONA products have bolt holes to fix attachments, and when installed on a certain import tool product, there is a slight gap and it does not fit with the Exactly. So, we modified the bolt holes a little with a drill, and it fits with a certain import tool and Exactly. The processing method is for reference only. If you are going to do the same work, please do it at your own risk.
View detail
It is a good, solid product.
Purchased for installation on a short roller standsJT125. I am not sure about the thickness of the penetrating shaft, but the overall construction is solid, so I can use it without any problem. View detail
jtrip first time STAND
I don't know if I have ever used the L or V receptacles, but I was able to raise them easily for the first time. I use it for storage. View detail
I bought it again.
Cushioning was also available, and the receptacle on the Swing Arm itself appeared to be falling apart.
However... after I bought it, I realized that the raggedness was just visible, but in reality it was just dirt... You can't look at it when you are tired.
Compared to the cheap STAND L-shaped receptacles, the quality of the Cushion section is better, first of all.
The cheap ones are thin rubber boards, while this product is a thicker, slightly softer board.
Damage to the Swing Arm is definitely less here.
View detail
![[Repair / Optional Parts] Repair Parts for Adjustable Rear Stand - U-shaped Attachment](https://img.webike-cdn.net/catalogue/images/96580/25262_TS.jpg)
Just what I was looking for.
The Rear Stand U-Hook is getting a little rusty and I was looking for an Attachment. View detail
usually
It can be used normally. It is a first-class manufacturer, so you can use it with peace of mind. View detail