Reviews
RearMaintenance
I have been using JTrip's STAND for a long time and have two types of Hooks. Now that I have a new hook on my car Both Sides, I needed a hook on the STAND side to match the new hook, and I thought the Rubber hook I purchased this time would be suitable for that. I have actually used the Rubber hook and it was a good decision because I only need about half the force I used to use. Another good point is that it does not get scratched. View detail
I'm not sure when it was lost.
I bought it because one of the four was gone and the other was cracking.
It explains that double-sided tape makes it harder to remove.
If so, I wish they would put it on from the beginning.
It was a hassle to put it on, so I used Vinyl Tape to prevent it from coming off.
View detail
Easier than Rear stand.
Rear and Quantity:I purchased a set and just pop it in the hole in the back of the Stem. The size of the hole is different depending on the motorcycle, so there are various materials:It has an Aluminum collar.Pull down the Lever and it lifts up easily. It is easier than FOR Rear. But Small Motorcycle:Z900RS CAFE has already installed DOREMI COLLECTION front emblem, so I think it has a lot of load on it, I have given up on it as it can't be helped. If it cracks someday, I will repurchase it. I have no complaints about the front stand. View detail
Heavy objects are easily lifted
There are many products out there, but I chose J-TRIP. It is already easy. However, L-Shaped Receptor and Small Motorcycle seem to be incompatible, so I purchased a V-shaped Receptor separately and am now using it. View detail
J-TRIPShort low ler Rear stand
I purchased this for my MT-09.
We considered cheaper companies A and D, but after reading your review, we decided to purchase JT-RIP.
Because there is no room in the length of Garage, we decided to use Short. It is also stable enough.
It helps with maintenance, but if it were cheaper, I would have no complaints.
View detail
Looks strong
If you order this Check your hooks diameter first, Looks strong and When lift up, it's solid without shaking. Don't forget to check the internal diameter size of the swing arm's hook and then jive it out of the two models from j-trip View detail
A constantly evolving Manufacturer
from before I've never done this before. is used
I have repurchased Matte Black from STAND, a collaboration between Nankai Parts and J-Trip!
When I received it in my hand and compared it with
Plating mirror surface was missing.
It looks cloudy like Uniqlo plating.
Or is there a secret that makes it rustproof?
The area of the Rubber on the receiver is now larger.
I think you can tell from the pictures.
Constantly evolving Manufacturer J-Trip
(Incidentally, DAYTONA part number 25298 has a 20mm Adapter on the front stand.
J-Trip is φ15, 17, 19, 22, 24, 27
DAYTONA is φ15.5, 18, 20, 22, 24, 27
Yes, it is subtly Gap!
I want to make it as close to the Stem hole as possible, so if you see this review, please give it a try.
Just 20mm is delicious in XJR1300 and FZr1000, so older Yamaha models would be good!
View detail
SV650 in '99 car.
As long as the width is positioned properly, the Swing Arm can be used perfectly without interference or rattling. View detail
It goes up impressively light.
I bought this STAND for Chain maintenance since gsx-s1000gt is not equipped with Center Stand. I had expected it to be able to lift up lightly from previous reviews and YouTube. When I actually tried it, I was impressed by the lightness that far exceeded my expectations. It may be an exaggeration, but it's almost like putting up a Mothers' bicycle STAND. j-trip is amazing.
At first, I was thinking of getting a V-accessory, but the staff at the motorcycle shop advised me that Stand for Beginner was the best recommendation if I was going to do it alone, so I bought it. As a result, I was right. I can lift up and down easily by myself without any worries. I can lift it up and down easily by myself without any worries.
View detail
Very easy.
I watched the official YouTubeChannel to prep it and it was very easy to use. Car wash and Chain Shiko are very easy. It is so easy to use that I wonder what I had to do with the Roller stand until now. If you wash and maintain your car frequently, this is a must-have item. Additional purchases are a V-receiver, a thing to keep the front brake lever pulled, and a bush to attach it to the car body. I purchased the "Helpful Rubber" as an insurance policy, but it has not been opened yet and has not been used. View detail
Easy to use
I was using STAND for the first time, but I got used to it and replaced it with V-receiver.
This type can be hung on the Hook while the vehicle body is tilted, so for the first time, it feels the same as STAND and Large.
This will expand the scope of work.
View detail
Easy Front up
I used it on my YZF-R1. It takes more force to raise it than I expected.
The tip of the clip seems to be a little shallow and I was worried that it might come off, but it seems to be large and sturdy.
The structure is such that the Gold genus directly hits the lower edge of the Fork, so those who are concerned about the Wound need to take measures to prevent it.
View detail
During maintenance such as Wheel, ChainMaintenance, etc.
I purchased Maintenance Stand for the first time and used it for the first time.
To be honest, it was my first time. Will it lift properly?" And "Why don't we take down Motorcycle?" I was worried about a lot of things, but it was surprisingly easy to Quantity:Set is ready.
It may depend on the person, but you can put something thicker on the Side Stand from the beginning to keep the Motorcycle straight and Quantity.:I think it would be easier to Set.
I am concerned that the Gold price is too high and that the Hook will be damaged because it directly interferes with the Hook, which is unavoidable.
View detail
Additional purchases
I purchased the Hook originally for maintenance etc., so I purchased only the Body.
I am satisfied with it because it will be useful for Large change if it is available.
View detail
Front stand
It's a win-win situation, but ….
Pros.
Adjustable, so it can be used for any type of car.
Cons.
Requires adjustment depending on the vehicle model, so it is a hassle when used for multiple vehicles.
However, small diameter vehicles cannot be used as they are due to their structure.
View detail
Slightly disappointed.
[How is it used?
Used in YZF-R6 (2019) with V-receiver.
I am new to buying Rear stand but have rented a Short from J-TRIP.
Was the one you received as per Image?
It was heavier than I expected, but not a problem at all.
The large size was as shown in the image, but it is still large compared to the short size.
How was your experience with it?
It is easy to raise and lower, and although I was worried about the short version, I made the right choice by choosing the long version.
However, even with Short, Stand for Beginner was easy and did not require much strength.
The screw holes are too large or the bracket is wobbly even when the bolt is tightened firmly.
[Points to note]
In the case of the V receiver, even at the lowest setting, it floats about 4 cm, so a little force is required to raise it.
If you want to raise it with light force, it is better to choose Stand for Beginner because Stand for Beginner will be in a lower position.
View detail
This will take care of most of the maintenance.
"I'm new at this. The name of the product gives the impression that it is for beginners.
It is not wrong, because it is an immense relief to know that the STAND will never be dislodged.
At the same time, there seems to be an atmosphere of embarrassment for a Veteran to use such a thing, as it is unnecessary for an advanced person who is used to maintenance.
But that's not true.
Since the rod for penetrating the Axle Shaft is threaded through this receptacle, it is not possible to replace the tire with this receptacle.
But...how much maintenance do you do that removes the Tire?
Even those who remove and maintain the tires quite frequently should not remove them more than once a week. (except for those who race hard).
When it comes to that, 'Never STAND off. This reception is usually sufficient for most maintenance.
On the contrary, I even feel that the frequency of maintenance will increase because it will become easier to Lift up.
I have actually increased my maintenance frequency.
I never had any difficulty with L-shaped receptacles to begin with, but still.
If you are a normal person who is scared to STAND-UP in an L-shaped receptacle, you will definitely see a drastic increase in maintenance frequency.
This is the first time for beginnersQuantity:Not a Set, when a beginner uses it for the first time. "Also." It is only optimal and is messy and convenient even for advanced users.
Not to brag, but it's been about a month since I bought this and I haven't used the L-shaped receptacle once.
If you don't remove the Tire, there is no need to use an unstable L-shaped receptacle.
View detail
the ultimate in the standard and a kind of ...
The L-shaped stand is the most popular and most universal type of stand for maintenance stands.
Very normal.
Among the maintenance stands marketed by various manufacturers, there is no one that is not based on this L-shaped stand.
The one made by JTrip has no outstanding features and is so ordinary that it is difficult to make an Impression.
Unless it is a special vehicle, everyone should buy this one.
There is nothing wrong with it, so please feel free to buy it.
If I were to point out a strong characteristic, it would be that it is narrower (smaller) than the L-shaped receptacles of other companies.
At first glance, this may seem to be a disadvantage, since it makes it easier to dislodge the device, but in fact, this may be the key to the problem.
This is because the area of contact with the swing arm is smaller, which increases the surface pressure, and it sometimes feels as if the swing arm is less likely to slip on the receiver.
I'm sure it's just a coincidence.
The overall size is small. When I applied STAND, a part of the receiver was in contact with the Sprocket and I couldn't turn the Tire." This is almost never the case.
(It should be a common mistake to try to shift it a bit and it comes off and knocks over the Motorcycle!)
It is not particularly spectacular, but it is a modest Recommendation.
View detail
Basic form of Garage maintenance
Quantities that are the very basics of home maintenance:Set would be this one.
Until now, I had been using a maintenance stand from another company, a type with a short handle, but it had become quite damaged, so I decided to buy another STAND made by JTrip.
First of all, it is not suitable for loading on a Transporter because of its long handle. (Probably the Tailgate will not be able to be closed.)
However, if it is to be used in a Garage with a maintenance Space, the handle should be long enough.
It is very easy to lift up with very light force.
I wonder if Small students can do Lift with the help of Small students.
It goes up that lightly, so those who are not confident in their arm strength should not worry.
The Roller also turns lightly, and the Roller is very stiff, yet Material:Since it is Rubber, Material:The feel is better than other companies' products using Plastic's Roller.
It is also quiet and luxurious.
And the reason why it has been highly supported by users for many years is because it has been designed with motorcycles in mind.
Although simple and straightforward in construction, it is possible to bring the receiver to an excellent position, resulting in a great user experience.
TDM900 is a normal Rear 17in. but with the height adjustment at the bottom of the Quantity:When set, the amount of Tire Lift is only about 2 cm.
The tire replacement is easy to do because it has hardly been raised, and above all, it is very light to apply STAND!
If you have a place to put it, I would definitely recommend it, and I don't think there is any point in buying a Type with a short handle if you are stingy with the little space you have.
For the main driver of the Circuit who wants to use it when loading a transporter, a shorter circuit would be better, but how many of you do that?
Normal people are definitely Koch.
Besides, I don't need STAND when loading the Transporter.
View detail
J-TRIP V Receiving Help Rubber
It is a useful product for fixing the V-receptacle Gold object and gives me a sense of security. View detail