Reviews
It is convenient to have it in Maintenance of Clutch type !!
Purchase for exchange of Clutch Spring of CYGNUS X SR 1YP.
It is convenient to have it when Belt drops in.
When exchanging Center spring and Clutch Spring
With or without a thing, the feeling of tiredness of the finger is completely different.
If there is one, I will recommend it as something useful.
View detail
Surprisingly convenient
Until now I was lucky enough to lubricate Wire, but if there was this I could lubricate properly.
After waiting for a while after lubricating it, you can see that dirty oil comes out from the other side and you can see that lubrication is successfully done.
Wire is also cleaned, it is well understood that new lubricant is injected well.
Because it is cheap, it is convenient if there is one.
View detail
I used it once and it was broken
I used it once and it was broken.
When exchanging the Tire of Off-road motorcycle, if I pull lightly to pass Air valve to Wheel with this product thinking that it is convenient, the wire has come off from the possession.
It may just be that the individual I bought was bad, but I can not recommend it to others for this quality.
View detail
It is not Nut twister.
I bought it to remove the rotten Nut of Exhaust System.
Nut twister has a helix inside the Socket and it is designed to dig into Nut, but this product is as you can see from the picture "Spiral" Is not a.
Even with this shape, I dig into Nut, but I just licked it and finished cutting the corner of Nut.
Once at the Burner, I also cooked Raspene, but I could not remove it with this tool, and it ended in disappointing results.
However, I cut off the corner of Nut and licked it, but since there is no Damage at all on the tool side, I think that it is robust.
Also, it seems that other people's review is well off, so I think that Large is durable unless Nut is rotten in earnest.
I think I will try again on another occasion. While expecting that it will come off.
View detail
Necessary enough
It is cheap, but it is necessary and sufficient performance.
I do not know where I can endure full-scale use,
As a hobby Rider, it is not too much to use so far,
It is very easy if you have Ring kind installation.
View detail
It was easy to use.
I used it to set the Snap ring with Oil attached. I never slipped and it was good.
It was also possible to change the angled tip by Smooth, enough to push the Clip into a narrow place.
View detail
Quantity : 1 Set of 3pcs. is
Quantity : 1 Set of 3pcs. is.
Replace Fuse because it has expired. I do not know whether it's good or bad as it's my first exchange, but there is no problem after replacement.
Fuse seems not to be disappearing so so it seems likely to be for the time being.
View detail
This is for Master cylinder disassembly!
Nisshin1 / I used it for disassembling 2 for FrontMaster cylinder. Because it is 90-degrees, the hole of the Snap ring is easy to see, the tip is long so it was easy to remove it! It is very convenient, but it is not rarely used tool, so personally I feel a bit high.. View detail
Was it meaningless as it was not enough for this?
I repeatedly disassembled and assembled with a mysterious Overflow, so I tried to buy it as well as Jet.
But since we need many tools before disassembling and assembling the carburetor, it was meaningless to try it as a special tool here.
On the contrary, because I am a cross, I feel like it will be over Torque.
I think that the universal tool I have used is better, people who have Universal Product do not need to buy it.
It seems to be a tool just to crowd the tool box. Since only the atmosphere is nice, the spirit may enter - - -
View detail
Tire exchange and ChainAlignment adjustment
I bought it for Tire installation after Tire exchange
In the textbook, I think it would be nice to fit with Swingarm's scale, but as I thought it was too much,
"Make the Length of the Bolt that jumps out the same" etc.
It was written.. Since these two do not match and it is not a new car, the distortion of the body and Swingarm etc etc. Maybe there is something, so maybe to some extent - - - I found this item where I was thinking. It is easy to install, and you can see that Alignment of the rear wheels changes with slight Nut tightening when you adjust. I convinced with their eyes and fixed the rear wheels.
I want to have one for this price.
View detail
I want to have fun,.
Chain and other things like crouching work are increasing
Purchase not to hurt your back.
Things are wonderful Small. Large fish that seems not to be strange even if Chibiko sits.
Well, it's user-friendly, but ...
Red lid of sitting part can be used quite well.
If you put something like Bolt immediately in Pocket in the side etc OK ('゜ д ゜ `)
When saying what the Red lid says
You can store good sticks etc
Oh, it's a joke.. But, because it is a little deeper, depending on the part it may come in.
I put the lap which I covered the Spoke wheel etc.
View detail
Turning the stuck Jet, the tip deformed...
When trying to loosen the stuck Jet, the tip of the Driver easily deformed, and the Plating also peeled off.
"* Light TorqueSpec. For Carburetor it can not be used for. Although it is being done in the Instruction Manual, it is said that it will be broken so easily.
After all, Jet fixed it purchased a normal slotted screwdriver again at home center.
I think that this product can not be used very much for a long-term leaving carburetor that Jet species may be stuck.
View detail
after all - - -
I bought it for Main jet for Replacement and free shipping fee.
As I thought, I could not use it because of Space problem.
Plating also peels off at Torque of Jet
It was a place where Plating was entering in the room Float indoors.
View detail
For tension adjustment of Chain ...
With Sprocket in between Red Parts and Bolt,
Read the direction of Chain with elongated Shaft.
Because the price is affordable, I tried purchasing.
From the adjustment that depended on feeling again, the work was completed securely and reliably.
View detail
Eliminate irritation at Tire exchange
Purchased at the accumulated Point. I thought that I wanted to see a friend using it. When I actually used it I could replace the Tire quite efficiently.
This is useful because it may take quite a while to find the beginning of TubeValve when exchanging Tire. As the frequency of use is low I think there is one in the tool box and there is no loss.
View detail
Good lid.
I make it solid..
It is good to have Rubber's lid.
Seal of Professional tool seems to come off, but I have not peeled off as it is.
Personally I like it pretty.
View detail
Convenient with Angle Difference Attachment !!
I always used Radio pliers to detach E Ring
I have experienced losing and dropping peaking many times
I bought a special tool this time.
Usability is a good feeling. Set of angle difference of Attachment is also
It was really useful and I did Big!
Price is also cheap Recommendation!
View detail
Chain adjustment is easy.
With adjustment of Chain line Quantity : Pair (for Left and Right) It is rather troublesome to match,
It takes a tremendous amount of time to stick to it.
(It has nothing to do with the model of PRO ARM or EccentricShaft)
However, with this tool you can adjust it straightforwardly in a short time.
There is Cover on top of Chain, no car type with no space (Also our GSX-R1000) It is
It is necessary to remove Cover and adjust it,
Removal time (time) Even if you compare the time without using this tool
It seems better to use this tool surely.
View detail
It might be unexpected
I purchased it for trial shipping adjustment.
I betrayed expectations in a good way.
It can be used quite well.. The sense that we did not expect increased the sense of profit. Even if I do not last long, it can not be helped at this price.
View detail
To drive and remove Wheel Balance Weight
PROTOOLSBalance Weight Hammer is used for Tire exchange to remove OEM's driven balance weight.
Because it is for Motorcycle, since the width of the part that grabs the weight is about 2 cm and it is Small, it is easy to use.
Weighing measured at 436 g, there was a response, Grip's Red Vinyl Cover also slid and gripped feeling well.
Also, on the Grip side of Joint, there is a blade that can cut pasted Plate Weight.
The part of Hammer that drives Weight has a rounded and bulged shape from the center, and it is considered that it is hard to scratch the surrounding Wheel when driving Weight.
The other day, we used ZYR 1400 Tire to remove Weight when exchanging, Balance was pasted Weight.
However, the weight attached to Rim stands out (It may be a matter of concern) Since it can not be helped, I am planning to change it to the driving weight of the OEM soon.
Personally, it is very useful.
View detail