Reviews
Stainless Steel unique high-pitched sound & CROSS highest !!
Purchase second strike sharp sound & more power purchase.
Selection Criteria
(1) Cheap
(2) Manufacturer well-known
(3) Rust resistant Material : Stainless Steel
(4) RightDual Silencer
(5) CROSSExhaust pipe
(6) OK with OEMSetting
(7) lightweight
It was an article that satisfied all of the above.
Returned, despite being chewed on the statement of unacceptable incomplete !!
Oh no, there is no manual !! Are you a beginner? No, no, who's on the current era 2 strike Exhaust Chamber Is not there anyone who can not change it..
Wear it all over your arm!
Results Degradation OEMExhaust Chamber over 20 years ago It was a pleasant miscalculation that Power & rushing up and slow Torque also increased.
Quantity : 2pcQuantity : Pair (for Left and Right) Maybe I should buy some...
View detail
Nice fabrication and welding. Good fit, only had to elongate one mounting hole. However, down pipe radius to big, so front wheel hits middle pipe when forks compress. So pipes are useless, and as you can't return them, a waste of money. Also, the baffl
Nice fabrication and welding. Good fit, only had to elongate one mounting hole. However, down pipe radius to big, so front wheel hits middle pipe when forks compress. So pipes are useless, and as you can't return them, a waste of money. Also, the baffle tubes are too short and don't reach the end of the last cone. They don't even line up, so restrict gas flow. Should have bought a set of Higgs. View detail
Fits: HONDA CB-1, HONDA CB400FOUR (water-cooled), HONDA CBR400F, HONDA CBR400R, HONDA CBR400RR, HONDA CBR400RR, HONDA CBR750, HONDA CBX750F, HONDA VT250 Z, HONDA VT250 Spada, HONDA VTR250, HONDA VTR250, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR, HONDA CBR900RRFire blade, HONDA CBR900RRFire blade, HONDA CBX400F, HONDA CBX400 F INTEGRA
Mizuno Motor [Xess] (VT Series) Exhaust Gasket
Since it becomes essential when exhaust system is exchanged
It is a Parts that is always in stock inventory
The other day, we replaced the exhaust system and the inventory has run out
So I bought it for regular use this time as well
I am still installing but I expect it to performance
The one used this time will be NC 27 series CB - 1
I will report again when I use it
View detail
Koshiba Naiko
I think that it is cheap and enough amount.
Slash Cut Exhaust SystemQuantity : 2 pc can afford.
He is doing a good job.
Until now it was rolling Glass Wool to exhaust interference type and used it.
Recently I wanted to quiet the sound more recently, I made Glass Wool a little extra on the Silencer that I had originally attached, made my own Baffle at the exit and squeezed the exit.
The sound fell to the extent that NORMAL was slightly larger than Large. It took a certain amount of deep bass and the residual pressure, finally calmed down.
View detail
Super very beautiful noise even more beautiful at high speed, very easy to assemble in a half hour, super nice look I adore Super beautiful noise encorre best at high speed, is very easy to assemble in a half hour, super nice look I love
Super very beautiful noise even more beautiful at high speed, very easy to assemble in a half hour, super nice look I adore Super beautiful noise encorre best at high speed, is very easy to assemble in a half hour, super nice look I love View detail
i recieved the plated chambers , although packaged in bubble wrap the chambers had noticible dents in them from handeling either at their warehouse or during shipment. The rear mounting tab brackets had significant rust build up the interface of the tab
i recieved the plated chambers , although packaged in bubble wrap the chambers had noticible dents in them from handeling either at their warehouse or during shipment. The rear mounting tab brackets had significant rust build up the interface of the tab re-enforcement and the exterior muffler tube. There was indication of improperplating as well as plating thickness problems as indicated by trace rust through the chrome on every chamber. the primary head pipes on all chambers were not round as should be expected from mandrel bent tubes but instead are all out of round and noticable. I will have to spend about 100 hours on the chambers to bring them up to expected quality. I must replate the areas that are showing rust and possibly reform the head pipes to get them round in diameter, the dents will require me to pneumatically and thermally shrink them out , this will probably mean replating the whole chamber. If i would have known the inferior workmanship i would have ordered the non plated chambers to make rework easier. The welds and base design appear to be decent but not normal custom welding quality. The price is right for the non plated parts but with the quality issues I would expect at least a $100 dollar less cost for the set unplated and 200 less plated . These chambers were the xess 250/400 individual silenced chambers. If you have no understanding of what denco, higgs speed or other quality chambers looked like new and are looking for a set of poser quality pipes these are ok, but if you are looking for at least as quality as the original Kawasaki factory stuff , these do not cut it at the price points View detail
Fits: KAWASAKI Z400FX/Z400J, KAWASAKI Z550
Great exhaust system for kz550a the hand bend pipe look beautiful, they also make great sound and power, webike customer service was very helpful and answered all my question before i decided to order, shipping was also very fast.
Great exhaust system for kz550a the hand bend pipe look beautiful, they also make great sound and power, webike customer service was very helpful and answered all my question before i decided to order, shipping was also very fast. View detail
Fits: KAWASAKI ZEPHYR750
This Exhaust is great! I have the Planted version and it looks awesome, original like the photo. Also i never mounted an exhaust system as fast like this. It simply fits perfect. It only took 25min to take the original exhaust away and put the new one on!
This Exhaust is great! I have the Planted version and it looks awesome, original like the photo. Also i never mounted an exhaust system as fast like this. It simply fits perfect. It only took 25min to take the original exhaust away and put the new one on! Also the sound is awesome too, thats the sound i want to have on my bike, not that bflflflflflfl, no it roars! Do u have the sound of Goose´s Z1 from Mad Max in your ears... :oDDD View detail