Reviews
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Recommended if you are concerned about AfterFire Ya
AfterFireYa noise is recommended for those who are concerned about the exhaust Gas regulation at the time of vehicle inspection. [Color] Clear is not possible. Therefore, I do not recommend it to those who think it is time-consuming to remove and install it for each vehicle inspection. View detail
Not associated with corrosion in piping
OEM Steel piping inevitably rusts and corrodes inside. This rust was unacceptable, so we decided to convert to titanium.
Whenever you say "hang" in the installation, ORing [Silicone grease]. Apply a thin coat of "PEEK" before assembling!
This is about it.
If the O-ring is coated with silicone grease, the O-ring will enter the cylinder block easily without getting stuck. If the O-ring is inserted without applying the grease, the O-ring may be damaged (I have experienced this in the past).
This is such a relief to know that the piping will not rust, that the rust will not eat into the rubber hose, and that it will not damage the water jacket.
View detail
Fits: HONDA CB400SF Revo, HONDA CB400Super BOLDOR Revo
so so
Simply replace with OEM Rear suspensionBolt.
However, I am afraid that the Hexagonal Wrench might lick if the Torque is applied when tightening the Bolt.
Considering replacing it with a Stainless bolt of the same size.
At first, I attached a screw lock and tightened it.
View detail
Shift feel changes
I was skeptical about it, but it works.
Shift feel is so much better.
When I saw the actual product, I felt the price was high....
The work is easy, but be careful because Bolt coated with Screw Lock is super hard.
View detail
Satisfied
This is what you get when you Lowdown.
I like the casual Mark!
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
3D Vendor Beauty Exhaust System??
The beauty of the curve of the exhaust pipe by 3D bender is the best among the external Full Exhaust System for Z900RS.
KFACTORY's, CLR-R+. (Plus) I am glad I chose Full Exhaust System.
The sound quality is neither too loud nor too quiet, just the right amount of sound, and the sound quality is typical of Titanium, which is good!
View detail
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
Exhaust System replacement at the same time
Still. The mileage is low, but I changed it at the same time as Exhaust System replacement.
It is safe.
View detail
Fits: KAWASAKI GPZ900R, KAWASAKI GPZ900R
Product Usage
Very good product, KFACTORY's products are very well made! View detail
95 pi.
No other size is this good! If you can find Other Brand Product, you may be able to buy it a little cheaper. View detail
Fits: HONDA CB400SF Revo, HONDA CB400Super BOLDOR Revo
One point Custom
I bought it at One point custom.
To prevent fading [Color] Clear blown and then installed!
View detail
I don't think it's useful
I don't think there is any change in shifting after installing it, not at all, which is disappointing.
Similar products made in China are only a quarter of the price. I don't think this thing has any technical content. -------------------------------------------------- -------- I didn't think there was any change in changing the gear after installing. It was completely disappointing. Similar products made in China are only a quarter of the price. I don't think this thing has no technical content. Powered by Google Translator
View detail
Nice fit.
Slider fitment can make the front lower part look more solid and fuller. insurance that will protect against unexpected damage. View detail
I think it's the Front Axle Slider from Best Buy.
Someone has already written a Review, so here is another perspective.
Front forkBottom and Brake Caliper are not affordable to replace with Wound.
But when I tried to buy a Slider for that purpose, it cost me 15,000 yen for two small chunks of DURACON and a mere stick of All Screw in a Vinyl bag. I was like, "Are you going to pay 15,000 yen out of the small amount of money you have in your pocket? It was an Image like that.
The quality of each part is so high that it can withstand the act of looking at it next to the PC until the day of installation after it arrives.
The shaft is not just an all screw, but a machined aluminum alloy shaft, so I did not use the included stainless steel screw, but prepared a separate Duralumin screw to assemble the shaft.
This is a great QUALITY product as others have stated in their Reviews.
Before purchasing the product, I was a little concerned about the Logo, which is often noticeable in photos, but in reality, it is a small one, so it is not particularly noticeable.
Anyway, we strongly recommend this product to those who are not sure which front fork slider to choose.
View detail
Wobble is gone and GEAR is in for sure! But Cospa ・・・・
[Fee Ring]
It worked better than I expected.
Scaupern (ss) and GEAR will be entered more reliably than NORMAL.
It is certainly better to have it than not to have it.
【attachment】
I'm fixing it with Bolt on the Side Stand.
Since this bolt is very hard and a screw lock agent is used, a large ratchet is required to remove it.
[Unfortunate point]
What can I say, the cospa is ・・・・
I'm pretty sure the Bolt is a two-point stop on other models, so it's positioned reliably.
The GSX1300R HAYABUSA has a single point stop, so I was worried about positioning.
(I was worried that the ClutchShaft might be loaded backwards when tightening the bolt during installation.
I think it was installed without any problems.)
View detail
Even with four OEMs
It can be used not only for Short TubeType such as YOSHIMURA, but also for OEM4. In other words, since the Swing Arm is replaced with MORIWAKI angle, it cannot be attached with the normal combination, but with this, it can be attached somehow. View detail
Exhaust pipe for Klx125
Purchased for installation of klx125 Exhaust System on Xtz125. View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX-R1000, SUZUKI KATANA, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSX-R1100, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1300R GSX1300R HAYABUSA
self-satisfaction
No one will notice it, so it is an area of self-satisfaction. K-factory's products are expensive, but I feel the beauty of modeling in their products. View detail
Smaller Accent
The small accents and gold on the feet are very effective. I hope this Parts will never be active …. View detail
Gasket
Purchased with the Exhaust System replacement.
Good quality and cost performance.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI NINJA ZX-14R
Brake's Touch is good.
The ROD of the Change Pedal of the Footpeg Kit, which was attached to the original car body and of which product I do not know, stuck and became unadjustable, so I replaced it.
Brake pedal requires disassembling the MASTER and reassembling the push rod, which requires a certain amount of tools and work skill.
The Brake master is now Rigid with Pilo, and the Brake Touch is much better.
More cumbersome than OEM push rod diversion, but more effective
The footpeg has good Knurl processing and bites the bottom of the Racing boots well, so it takes some getting used to when shifting the foot forward during Brake and Shift operations.
Change Pedal tip is good for DURACON and less aggressive to Boots.
This is the only place where the footpeg itself is made narrower by pulling it closer to the car body, which is one of the reasons for the choice.
View detail