• Home
  • Product reviews
  • Search reviews
steps-review.png
Filter
icon-webike.png
Write a review and get Webike Points!

Reviews
JvB Moto Clear all
[KEDO] Front Fork Boots
JvB Moto
[KEDO] Front Fork Boots

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
5/5

Massive impression of XSR700

The front fork is an item that changes the impression of XSR700 and MT-07, which may look a little weak.
After much deliberation with the Fork Boots made by Wysskia, we chose these, which look thicker.
There was a concern about the fitting aspect with OEMOption, but there was no problem at all.

If you don't have access to a shop where you can remove the Fork, you should ask the shop to do it for you.

There are three small holes on each side for air to enter and exit the Boots, but they are still blocked when purchased. You can shred them by picking them up with your fingers and pulling, but I think it is easier to shred the remaining BALI after poking them with a thin tip. If the vent hole is not opened, air will be forced out when the Fork shrinks, and the negative pressure when it expands will cause the Boots to cave in, resulting in a very poor parenthesis. (I've done this).

It is also recommended that the pre-2020 XSR be fitted with the OEM ForkUpper Cover for MT-07.
1WS-23121-01/Cover, Attp 1
1WS-23131-01/Cover, Attp 2
43F-23188-10/O-Ring
*O-ring is a Quantity:2pc. Set required
These three items can be purchased together at WeBig. View detail

[KEDO] Footpeg
JvB Moto
[KEDO] Footpeg

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
5/5

Exactly on 2015MT-09To Racer

I installed this on my 2015 MT-09 toRacer. The OEM footpeg on the MT-09 is not suitable for long touring, so I replaced it with this footpeg. I feel more stable and it is easier to do ankle grips and standing.
The Left SideOEMfootpeg of the Racer has a crimped pin, so it was necessary to file off the crimped portion before installation, which was also done without difficulty. View detail

[KEDO] LED Blinker Bracket
JvB Moto
[KEDO] LED Blinker Bracket

Fits: YAMAHA MT-07, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-09

Japanese Webike user
jp
5/5

of good quality

The product itself is very solid and not cheap looking.
Since it is installed in a place where it cannot be seen, I am not particular about its appearance, but it can be installed with peace of mind.
The performance is fine and I expect it to be durable. View detail

Kedo] Front Fork Boots
JvB Moto
Kedo] Front Fork Boots

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
jp
5/5

To SCRAMBLERCustom

These are normal Fork Boots. You will need to remove the fork when installing.

The Boots themselves are easy to install.
More than that, the OEM Fork Guard O-ring is a curmudgeon.
This makes it difficult to re-fit the fork as it can get stuck or twisted.
Caution. View detail

[KEDO] LED Headlight & Cover Kit
JvB Moto
[KEDO] LED Headlight & Cover Kit

Fits: YAMAHA MT07

Japanese Webike user
jp
5/5

MT-07 with round eyes spec.

It is one of the options for those who want to make their MT-07 a round-eyed Spec.

Note that there are different types of Covers for different years.

Exclusive Design (same as XSR700) so it can be installed with Refreshing.

However, you need to modify the body side when you install it.
Arm holding the Harness of the Right Side near the with Handle interferes with the Cover, so bend it.
It is not so difficult if you do it with Pliers, but be careful not to break it.
Harness handling needs to be moved a bit to fit somewhat.
And the color of the Harness on the Body side is different from the Harness on the Headlight side.
Harness is not waterproof, so you need to waterproof it accordingly.

Color:Unpainted, has some BALI and dents. You can't see it from a distance even if you put it on as it is.
I left it in the hands of a PRO painter and had it beautifully matted Black.

The Instruction Manual is entirely in German.

If you have the ability to handle the above to some extent, I think you can install it without any problems.
If the above is difficult or you don't understand it, ask Shop or other people to help you. View detail

[KEDO] Footpeg
JvB Moto
[KEDO] Footpeg

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
jp
5/5

Style and comfort are GOOD!

This is the Footpeg I used for the SCRAMBLERCustom on the MT-07.

It will be of EnduroType.

Simply remove and replace the OEM Product.
If you have trouble removing the split pin, you can cut off the butt part with a nipper.

It is very wide so it is very stable with legs on it.
It is moderately toothed, has less Damage to Shoes and is less slippery.
Standing is also easy.

The Knee Slider will be gone, so if you have concerns in that area, give it up. View detail

【Kedo】LED Turn Signals
JvB Moto
【Kedo】LED Turn Signals

Fits: YAMAHA MT-07, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-09

Japanese Webike user
jp
5/5

The Headlight area is neat.

This is the Front Blinker I bought when I made my MT-07 into a SCRAMBLER Custom.

It contains a pair of Blinkers and a Heat Shrink Tube.

Jvb has a Harness for YAMAHA motorcycles on the market and you can install it without any care.
I processed it with Bullet terminal.

Heat Shrink Tube is done with a heat gun, but I shrunk it by burning it with Burner of the CD can so that it may not become a direct fire.

It will be an LED Blinker, so the OEM Blinker relay will not work correctly.
An external LED compatible Relay is required.

I'm ↓ so it's working correctly.
https://www.webike.net/sd/24232608/
Relay is easy to replace.

Installation position is under the handlebar of the front brake and clutch lever.

Co-tighten the Nut on the Handlebar side.
Quantity:Pair (for Left and Right) In a sense, it's safe to say that you can't put it on by mistake because the shape is different.

I don't think there are any problems with light intensity or visibility. View detail

[KEDO] Tank Center Cowl Kit
JvB Moto
[KEDO] Tank Center Cowl Kit

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
jp
5/5

Super cool with the Solo seat!

If you're going to put on the JvB Moto Solo seat, I'd say the Center cowl is a must.

There is no use for driving without it, but it will be put on if you think about Design because it will be skewed between Tank.

First of all, it is necessary to cut off the BodyTank Side Cowl.
It comes with a sheet of paper for cutting off the seal. Attach it as instructed in the Instruction Manual, and cut off the unnecessary parts.

I bought a cheap Leutor from Amazon and cut it carefully, no problem.
If you can't do the work around here, ask Shop to do it for you. The cutting surface is basically hidden by the center cowl, so you might be able to get away with a messy job.

And the actual connection to the Side cowl, the Instruction Manual says to drill a hole with a 3mmDrill and stop with the supplied Tapping!!!

I'm afraid of cracking the bottom hole. I'm afraid of cracks even if I drill a hole.

If I do not make this part easy to remove, when I remove the Side cowl, I always have to remove both Sides together, so I did not use Tapping, and because I had a Push rivet of appropriate size, I made the bottom hole a little large with Footpeg Drill to fit it, and connected 4 places. I connected it.

Because it is the one which is often used for the connection of Cowl originally, there is no problem in the vibration etc. Because the tapping of the attachment is Silver and stands out in my body color, it was GOOD that I changed it to the Rivet of Black in style.

Also, it is assumed to be Large, but Color:It is Unpainted. it is in the state of Gel coat of FRP.
I left it to the paint PRO to match the body perfectly.
Candy paint will cost you a fair amount of money, but I can gladly pay for this finish myself, as I don't have the time or skill to do it myself. View detail

[KEDO] Solo Seat Kit
JvB Moto
[KEDO] Solo Seat Kit

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
jp
5/5

Anyway, it's hard. And thick.

The coolness comes first.

The Urethane is just so hard that it sits on your butt the worst.
It's thicker and has more width, so it's much less comfortable on your feet.

I was happy because this was my only option to make a JVB Custom.
It's definitely not a butt-ache product, so don't buy it if that's what you're after.

It would be great if you could improve the anchors yourself, or if you could just send them out for Seat replacement.

And Quantity of Luggage Rack and Tank centerCowlKit of the same Manufacturer:Please note that the Set is assumed to be Large.Instruction ManualGermany language, so use Google Translate or something. View detail

[KEDO] LED Blinker M8
JvB Moto
[KEDO] LED Blinker M8

Fits: YAMAHA MT-07, YAMAHA MT-07

Japanese Webike user
jp
5/5

Small but bright.

Universal M8 Screw Size LED Blinker.
It contains a pair of Blinkers and a Heat Shrink Tube.

Jvb has a Harness for YAMAHA motorcycles on the market and you can install it without any care.
I processed it with Bullet terminal.

The structure is simple and I think it can be installed without any problem even if it is not YAMAHA.

Heat Shrink Tube is done with a heat gun, but I shrunk it by burning it with Burner of the CD can so that it may not become a direct fire.

It will be an LED Blinker, so the OEM Blinker relay will not work correctly.
An external LED compatible Relay is required.

I'm ↓ so it's working correctly.
https://www.webike.net/sd/24232608/
Relay is easy to replace.

Of course it is just fit for Fender Eliminator Kit of the same manufacturer. View detail