Reviews
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
Side Stand is perfect!
Panigale and Streetfighter boots do not have good footing for most Japanese people. I am 177cm tall, but when I use a type of racing boots with the heel covered with a resin protector, like the ones from Pine Starz, the part where the heel hooks onto the side stand is too short and I slip and run away. When I am in the riding position, I can get it out with about a 50/50 chance, so when I am in good health, such as when I am refueling, I can stick it out a few times, but when I am tired, I can't get it out. No more." and I had to get off the Motorcycle and take out the Side Stand. If I had a normal leather or rubber bike, I would be able to get off the motorcycle and put out the Side Stand without any problem.
The AELLA product is almost twice as long as the AELLA product, so the Side Stand can be easily produced.
View detail
Wow that's cool
I installed it because I was lonely around the Front.
Circuit also runs, so Protector in the event of a fall.
I hope it will be ??
View detail
Fits: KAWASAKI NINJA2 Helmet50RR, KAWASAKI BALIUS2, KAWASAKI ELIMINATOR 250V, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA400R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZEPHYRX, KAWASAKI ZRX1100II, KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZZR1400 (ZX-14), KAWASAKI VERSYS, KAWASAKI VULCANS, KAWASAKI ZRX1100, KAWASAKI ZX-9R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI Z1000
Convenient for maintenance
It's OEM Parts and convenient for maintenance. View detail
Fits: DUCATI STREETFIGHTER V2, DUCATI PANIGALE V2, DUCATI STREETFIGHTER V2, DUCATI PANIGALE V2
It may not be the original use.
When I was standing up, this probably saved me from damaging my Cowletc. (not guaranteed in all situations)! (Not guaranteed in all situations) View detail
Over Racing front axle slider for z650rs
The front axle slider for z650rs from Over Racing is well made and fits the z650rs stock front wheel with minimal tools necessary to install. It’s a direct bolt on and no other necessary bolts or screws are needed for installation. The sliders tip is flushed on the axle as you can see in the picture and installation time is quick. Just insert it in the hole in the front axle and screw it tight and its done. View detail
z650rs Over Racing rear axle slider
In the picture included, the rear axle slider is attached to the top of the bolt that holds the rear wheel. This is possible because the z650rs has a hole in the rear axle unlike in the other z650 lineup. It is an easy install and the sliders looks and feels well made. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
The footrest for Monkey
I bought a footrest for a Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is what you need. It came up without any problems, the installation is fast and easy. The price and quality are minimal. I recommend it to everyone. I bought a footrest for the Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is just right. Fits without problems, installation is quick and easy. Minimum price and quality are high. I recommend to all. View detail
Simple but good performance
It looks good, but the grip is good, so there is no burden when standing due to the grip of the boots and chassis. Installation is very simple and I think it's good because it prevents scratches.About quality and texture View detail
When the Center Stand is installed, a little effort is required.
The Instruction Manual indicates that the cover under the tank must be removed for installation, but it can be installed without removing the cover.
On the Left Side, the lower claw is first fitted and then fastened with two bands (Large and Small).
The Left bottom of the Right Side Cover interferes with the Center Stand, so it must be trimmed, including the claws.
I think you should cut at the base of Radio pliers and Cutter to Beauty!
Then fasten with Largex2 Band
Bundling Electrical Cord Covers Next Needle Gold Makes Banding Easier
View detail
Installation is done by aligning the machined portion of Thermo on the Right Side.
The Under Cowl is held in place by four mounting brackets. The mounting brackets are held in place by bolt1 pcs, so they can be fixed in any position. Therefore, it is easy to install by aligning the Right Side Cowl so that the notch on the Right Side Cowl matches the protrusion of the Thermo. View detail
Cospar good
I bought this because I was told that without it, the Swing Arm would be scraped off in the event of a fall.
The length of the shaft that came in the first package was wrong, but they sent it to me right away.
I am satisfied with the quality and response for the price.
View detail
I'm not sure how effective it is, but just in case.
The quality of the slider itself seems to be a little small. Well, I bought this Slider just in case. I don't know how well it works yet, and I don't want to know. I don't even want to know.... View detail
The beauty is that no drilling is required.
I bought it just in case. The quality of the Bracket is high, and I would be happy if the price were lower. View detail
Nice engine guard and easy to install!!
Installed on 2023 Honda Rebel 1100 manual - Great quality of those engine guard, easy to install and looks nice. A couple thing I likes to mentions 1. Be careful when removes the manufacture screws off the bike, they could be very tight and the radiator will prevent your hand able use full power, watch out to strip off the screws. 2. Those 2 engine bar in place, it seem kind a close to your shift gear and rear brake paddle, for those have a long foot and not sure how other biker habit of their feet positioning during ride or shifting, you could hitting the engine bar so adjusting your feet positioning or habit for first couple week might helps. View detail
When the Center Stand is installed, a little effort is required.
The Instruction Manual indicates that the cover under the tank must be removed for installation, but it can be installed without removing the cover.
On the Left Side, the lower claw is first fitted and then fastened with two bands (Large and Small).
The Left bottom of the Right Side Cover interferes with the Center Stand, so it must be trimmed, including the claws.
I think you should cut at the base of Radio pliers and Cutter to Beauty!
Then fasten with Largex2 Band
Bundling Electrical Cord Covers Next Needle Gold Makes Banding Easier
View detail
It's not too obvious.
Since the Body is Black, it can be worn on the muddy ELIMINATOR SE without discomfort. The effect is not clear yet. View detail
Fits: SUZUKI V-STROM250, SUZUKI V-STROM250, SUZUKI V-STROM250
DL1000 V-STROM250 2023
[How is it used?
From city driving to touring.
I am satisfied with the way it looks.
Was the one you received as per Image?
As per Image, the welding and ?painting are ?nice.
Was the installation difficult?
The exhaust Layout was changed from the 2023 model year,
I thought the installation would be sturdy enough to install a large size, but it was installed without interference.
I had a hard time accessing the tools. I had a hard time accessing the tools.
Socket, Glasses Wrench, Spanner, Long Hexagonal Wrench
We were able to install it in half a day, making full use of a short Hexagonal Wrench.
How was your experience with it?
It looks good, and if you fall down standing up, etc.
I think it will prevent some Damage.
[Included Parts:were they on?
All Bolts and Washers were available.
[Was there anything that disappointed you?
Not particularly.
Other items that would be helpful
Instruction Manual can be downloaded from the web,
Print it out and work on the installation, it's easy to see.
View detail
Fits: HONDA REBEL250, HONDA REBEL250S EDITION, HONDA CL250
resolving a severe earthquake
The tremors from 90 km dramatically disappeared and I am not tired at all even when touring long distances. View detail
Fits: BMW S1000R, BMW S1000RR, KAWASAKI Ninja250, KAWASAKI Ninja400, SUZUKI GSX250R, BMW S1000XR, HONDA CBR1000RR, KAWASAKI ZX-10R, KAWASAKI ZX-25R, SUZUKI GSX-S1000F, SUZUKI GSX-S1000S KATANA, SUZUKI GSX1300GSX1300R HAYABUSA, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Maintenance Stand and Dress-up as well.
I purchased this product to use to stand a Maintenance Stand.
We decided to purchase the product because of its affordable price compared to other companies and the fact that it is a trusted Posh.
The design has good parenthesis, and the anodization is beautiful.
The surface of the STAND is scraped off after standing on it several times, but this is not a particular complaint as it is an unavoidable part of the product's characteristics.
I think it is worth buying even for one point dress-up purposes.
View detail
Universal Engine Guard
Not only does it simply protect your motorcycle, but it is also highly universal as it can be fitted with a variety of accessories.
Installation requires a panda jack or Torque wrench, so it is not easy for everyone, but in the end, it is a Bolt On product in the extreme, since all you have to do is remove the Bolt and install it.
Panda Jack and Torque wrench are cheap enough, so if you need to buy more, it will cost about 5000 yen or so, or about 15,000 yen if you order from the Shop.
It is easy to do if you watch YouTube for reference.
Drink holder, Glass Holder, Tool Box and Fog Lamp
Multi Bar named Engine Guard.
Since other companies' Engine Guard cannot be installed in various ways, I recommend this product from KIJIMA.
View detail