Reviews
Peace of mind and trust
I had previously installed a Hose made by another company, but the manufacturer's instructions for the CB750FRear brake were about 40mm too long, and although I could use it, I did not like the way it was being used because it was unnatural. After careful investigation, I found out that it was because there was no just size in the manufacturer's standard. This time, I found that this product, which was on sale at a discount price, had an approximate size, so I purchased this one. When I installed it, it was almost just right, and I felt no discomfort in handling it. As an aside, the size of the fitting of a certain Manufacturer is 13H, so it may not have Spanner, but this product is 12H, so I am grateful for that. View detail
Everything is included in the price.
Replacing a 28 year old Earls hose.
The kit comes with everything you need, including the correct length hose, banjo adapter, washer, banjo bolt, and air-free bolt, so you don't have to do all the research and buying by yourself.
The angle of the NORMAL hose and the banjo adapter were different, so I contacted Active through webik, but they said that the configuration was based on the length of the hose and the handling of the adapter.
When I actually put it on, I was able to make the handling more Refreshing than NORMAL for sure. Well thought out. Sorry I suspected a packaging error.
It's Goodridge's Hose, so it can't be helped, but the Wrench used for the Crimp on the Banjo adapter is 7/16, Inch tool. If I could only manage this part, it would be perfect.
However, it is very nice to be able to use it without the tedious and difficult Hose process!
I'm glad I bought it
View detail
Trust Brand
I used it on a 2011 CBR1000RR.
The replacement is a simple task since all you have to do is to drain the brake fluid and replace the hose, but if you are worried about the parts around the brake, you should ask a motorcycle shop for help.
The length and fitting of the hose are perfect, as the kit claims to be model-specific. There are no separate parts to prepare, and the parts included in the car-specific kit are all that is needed.
Color is [Color] I chose the Smoke hose, and I think it is a very good parenthesis as a custom hose that is not too assertive. I think it is very easy to control even in the middle of a corner.
This product is recommended for those who wish to improve the control of the rear brake.
View detail
Hose replaced in conjunction with Caliper replacement
I replaced the hose with Stainless Mesh to match the Caliper replacement. The Banjo adapter is angled, which may be a prerequisite for the replacement of the Normal hose. (45°?) So I feel that the angle is a bit too much for the Crab type Brembo. I think I will change it to Straight or something with a looser angle for the next brake fluid change. View detail
Rear also replaced together
What made you decide to buy?
We have been aiming to create a motorcycle that is as good as the OEM models with enhanced brakes, and we have been thinking of enhancing the brakes since we took delivery of the ZX-6R. Build Aligned Vehicle Type Bolt-on Kit for Rear replaced.
[How was the installation?
As with the Front, the Master Cylinder was replaced at the same time, so it took about 2 days to complete the entire job.
The ZX-6R's brake goes through an ABSUnit, and that ABSUnit is located under the tank. First, the tank is removed, and next, the air cleaner box is removed.
Before starting work, drain the brake fluid from the oil tank, and then remove any remaining brake fluid from the brake line by suctioning it out of the caliper. Cultivate the surrounding area before proceeding.
The rest of the work was done according to the Installation Instruction Manual, but removing the OEM hose was more of a puzzle than the front. In particular, the hose from ABSUnit to Caliper was not coming off properly. Since the OEM hose will not be used in the future, I took a rough route and cut off the pipe in the middle with a wire cutter and it came off easily. (Lol)
Rear hose replacement was a bit more troublesome than the front hose replacement. I had to remove the foot cover of the babyface, oil tank and hose. (The oil tank was also replaced with [Color] Smoke at the same time.) The rear master area was a bit complicated to handle, but we proceeded with the work. Unlike the front, the method of fastening to ABSUnit is different, using a different collar and a different thickness of crash washer. As with the front, there are many places to tighten, and it is recommended to use the GOODRIDGE Torque and mark the completed installation. If you don't check it many times, you won't be able to check it once the tank is attached.
Please note that there is a law that states that only the owner of the motorcycle or a licensed mechanic can perform maintenance and parts replacement related to the brake. I am a former Owner." Please use this as a reference only, as we have performed maintenance on the
How was your experience with it?
If you often replace brake lines. The touch goes from squishy to direct." I don't have the skills to feel that. However, I think the durability will be improved because the rubber hose will be changed to stainless steel mesh unlike the factory one. So why did you replace the brake lines? I think it's to get the best performance out of the parts that were replaced at the same time! Also, because the brake lines are thinner, the clamps that hold the ABS in place can no longer be used. So you can use the genuine Kawasaki part 92171-0921 clamps used on the H2, ZX-10RR, etc., so you can buy them at the same time. You need three of them for both front and rear.
View detail
Fits: KAWASAKI ZX-6R 636, KAWASAKI ZX-6R
Custom feeling has been increased.
What made you decide to buy?
We have been aiming to create a motorcycle that is as good as the OEM models with enhanced brakes, and we have been thinking of enhancing the brakes since we took delivery of the ZX-6R. Build Aligned Vehicle Type Bolt-on Kit for Front replaced.
[How was the installation?
The Master Cylinder was replaced at the same time, so it took about 2 days to complete the entire job.
The ZX-6R's brake is connected to the ABSUnit, which is located under the tank. To remove the tank, the remaining gasoline must be removed first, but be careful when handling the gasoline, as it is a dangerous substance.
After removing the tank, the next step is to remove the air cleaner box. (Piping is connected to the Fuel Tank and Air Cleaner, so mark them and cure them to prevent Garbage from entering)
The throttle valve should be cured so that no garbage or foreign matter can enter the valve until the work is completed. It is also recommended to clean the filter while removing the air cleaner box.
Now, before the work is done, all the Brake fluid is drained out. Cure the surrounding area before proceeding. In case of emergency, store water in the bucket and wash the Fluid if it touches the Fluid! If it touches the Fluid, wash it.
The rest of the work was done in accordance with the Installation Instruction Manual, but removing the OEM hose was a puzzle. While doing so, we proceeded with the work while neatly working around the line, and then set the handlebar to the quantity:Pair (for Left and Right) The brake line was moved to the "0" position so that there would be no load on the brake line. There are many places to tighten, so it is safe to use the GOODRIDGE Torque and mark the tightening points when completed. The work was then completed by bleeding the air. Be careful not to turn on the power before and during the air removal. If you turn on the power by mistake, it will cause a malfunction of ABS and you will be sent to the manufacturer.
Please note that there is a law that states that only the owner of the motorcycle or a licensed mechanic can perform maintenance and parts replacement related to the brake. I am a former Owner." Please use this as a reference only, as we have performed maintenance on the
How was your experience with it?
If you often exchange Brake lines. Touch goes from squishy to Direct." I don't have the skills to feel that kind of feeling. However, unlike the OEM hose, the rubber hose is replaced with stainless steel mesh, so I think the durability will be improved. So why did you change the brake line? Well, I think it's to get the best performance out of the parts that were replaced at the same time! Also, because the brake line is thinner, the clamp that holds the ABS in place cannot be used. You can use Kawasaki OEM Parts 92171-0921 Clamp which is used on H2 and ZX-10RRetc.
View detail
I've replaced the Front and now the Rear too!
What made you decide to buy?
We have been aiming to create a motorcycle that is as good as the OEM models with enhanced brakes, and we have been thinking of enhancing the brakes since we took delivery of the ZX-6R. Build Aligned Vehicle Type Bolt-on Kit for Rear replaced.
[How was the installation?
As with the Front, the Master Cylinder was replaced at the same time, so it took about 2 days to complete the entire job.
The ZX-6R's brake goes through an ABSUnit, and that ABSUnit is located under the tank. First, the tank is removed, and next, the air cleaner box is removed.
Before starting work, drain the brake fluid from the oil tank, and then remove any remaining brake fluid from the brake line by suctioning it out of the caliper. Cultivate the surrounding area before proceeding.
The rest of the work was done according to the Installation Instruction Manual, but removing the OEM hose was more of a puzzle than the front. In particular, the hose from ABSUnit to Caliper was not coming off properly. Since the OEM hose will not be used in the future, I took a rough route and cut off the pipe in the middle with a wire cutter and it came off easily. (Lol)
Rear hose replacement was a bit more troublesome than the front hose replacement. I had to remove the foot cover of the babyface, oil tank and hose. (The oil tank was also replaced with [Color] Smoke at the same time.) The rear master area was a bit complicated to handle, but we proceeded with the work as we went along. Unlike the front, the method of fastening the ABSUnit is different, using a crash washer with a different collar and thickness. As with the front, there are many places to tighten, and it is recommended to use the GOODRIDGE Torque and mark the completed work. If you don't check it many times, you won't be able to check it once the tank is attached.
Please note that there is a law that states that only the owner of the motorcycle or a licensed mechanic can perform maintenance and parts replacement related to the brake. I am a former Owner." Please use this as a reference only, as we have performed maintenance on the
How was your experience with it?
If you often exchange Brake lines. Touch goes from squishy to Direct." I don't have the skills to feel that kind of feeling. However, unlike the OEM hose, the rubber hose is replaced with stainless steel mesh, so I think the durability will be improved. So why did you change the brake line? Well, I think it's to get the best performance out of the parts that were replaced at the same time! Also, because the brake line is thinner, the clamp that holds the ABS in place cannot be used. You can use Kawasaki OEM Parts 92171-0921 Clamp which is used on H2 and ZX-10RRetc.
View detail
It looks tighter in Black.
[How is it used?
I used it on the rear brake of the XJR1300C, the main vehicle.
Both Caliper and Rear brake master are NORMALSpec. and footpeg is OVER Rear Sets.
This time, we have replaced Brake Pads and performed an Overhaul of the RearBrake Caliper.
We exchanged the wild OEMHose for the stylish Goodridge.
We have selected BlackHose's Black stainless full Black Spec.
I'm happy with how crazy tight it looks.
Was the one you received as per Image?
The texture and product details were as good as the Image.
The connection to the rear caliper was a bit of a surprise because, unlike the OEM, it was a direct stick type to the caliper.
Was the installation difficult?
The installation itself is not difficult, although there is a hose holder on the back of the Swing Arm.
Be sure to go through this Holder, as Goodridge's Hose is much thinner than OEM.
Cut the HoseRubber attached to the OEMHose with a Cutter and wrap it around the Goodridge Hose.
When tightened through the Holder, it is firmly secured.
Also, a note on the air bleed. First, XJR's RearMOSCaliper has Breeder's Quantity:2pc. Since it comes with a Set
Be aware that you have to bleed air from two places, and it's easy to miss the Breeder on the reverse side.
It is very difficult to turn a Breeder with a rear wheel, so short 8mm Glasses are easy to use.
And here's where it gets even more important:Caliper will not release air while locked in its normal position!
Remove the Caliper and lift it to the upper side to bleed air with the Breeder Up.
I was stuck in air venting hell for about 2 hours before I realized this. 500ml of Fluid was also wasted (lol).
How was your experience with it?
The Touch is now very chunky and I don't have to deal with the unpleasant feeling of the OEM's squeezing.
[Included Parts:were they on?
As you can see in the picture I took for you.
[Was there anything that disappointed you?
Nothing in particular, I personally prefer copper for Crash washers, so no Aluminum please!
View detail
Durability and Dress-up
The entire brake rotted out, so I replaced it with a Master Cylinder for GSX750S and this Hose. The brakes are lighter and work better than before. However, I don't expect much since the front is single disc and the rear is drum. By the way, I changed Clutch Wire to KITACO Red, Throttle to Single High Solo and Meter Wire to Stainless Mesh. View detail
Used for GSX R1000
Hose was also replaced along with the MASTER exchange. I think it is good that I can decide the length by myself. View detail
Fits perfect!
Fits and routes smoothly from the rear caliper to the rear master of the bike. Banjo bolts included are stainless steel. View detail
Used on xjr1200 + 65mm bremboCaliper
When replacing the Yamahabrembo→65mm bremboCaliper on my XJR1200 95
The direction of the banjo bolt connection is different from that of the original Caliper.
We selected the hose set for the XJR1300, which has the same 65mm caliper and banjo bolt mounting orientation.
Caliper support has slightly lowered the Caliper mounting position.
It is a length that does not interfere within the Stroke range of the OEMFront suspension.
HoseQuantity:Pair (for Left and Right) It is also kind enough to include aluminum parts to fasten the
The firm Touch was able to provide braking power.
View detail
Fits: YAMAHA XJR1200, YAMAHA XJR1200R, YAMAHA XJR1200
For Clutch hoseXJR1200 Sufficient performance
I have never replaced the NORMAL clutch hose.
We were concerned about deterioration over time, so we replaced them.
I don't see any change in the feel of Clutch's controls.
It is perfect because the replacement has increased reliability.
View detail
Fits: HONDA CB1300SF SP
semiCustomOrder made
The Hose routing was changed by installing a brembo Caliper.
When ordering from Webig, I was able to extend the hose on the caliper side and change the banjo bolt to a for Brembo in the remarks column.
View detail
Black is very Simple and uniform.
It's all Black, so it's very unified. View detail
Maybe a little long.
From Brake master to Separator
MASTER20°, Separator side Straight by using Separate handle of Tagos
I think 310mm would have been fine, but I'm glad I'm avoiding Wiring and Fork.
View detail
It is easy to Control.
It is easy to install and is of the highest quality.
Control is good and works well.
I am glad I installed it.
View detail
Fitting is the highest by the design only for a vehicle type. Texture is also very best.
Fitting is the highest by the design only for a vehicle type.
Texture is also very best.
View detail
Since the hose of normal had branched by front fender side, and the exhaust air omission was bad, they were exchanged here. Although normal was not bad, either, probably because exhaust air escaped from the touch itself thoroughly, it became more shar
Since the hose of normal had branched by front fender side, and the exhaust air omission was bad, they were exchanged here.
Although normal was not bad, either, probably because exhaust air escaped from the touch itself thoroughly, it became more sharp touch.
Touch with many dead strokes currently felt by the normal master cylinder also disappears.
The banjo by the side of a caliper and an upper caliper mount bolt interfere in a problem, and a bolt does not escape from it.
It interferes also in a socket wrench and does not enter straight.
Although left-hand side is cancelable by attaching a hose after only a few has shaken outside, since right-hand side has a stopper, unless a stopper is shaved, it is unsolvable.
Those who remove a caliper by the pad or a tire change frequently need a caliper adapter and the device which induces space to the circumference of a bolt using an elbow etc. 45 degrees.
View detail
The direct feel rose.
The direct feel rose. View detail