Reviews
Design is a good idea (depending on the type of car and the direction you are going).
The size is the same as the image.
The mounting is done by friend-tightening the NumberMounting Bolt. In some cases, it may be better to increase the bolt length by 0.5mm.
I love the fact that it is legal without interfering with the Image that I want to lighten the Rear under Number and without being too assertive.
View detail
Sits great!
Mistuba Sankowa EDR-21Gα for Camera mounting.
If you have trouble finding a place to install the RearCamera, use this one.
All your problems are solved at once!
View detail
I think it's fine, but at your own risk.
I used it in the field where I put brembo4POD on VT250 SPADA.
The one I received is the one with no problems.
The BoltQuantity is included with the Caliper.:There are 2pc.
Be sure to check the fastenedTorque properly.
I think the Pad on the inside diameter side of the disc is slightly sticking out.
I tried to put it as far out as I could, but it was still too far. (;^ω^) It's like
What does it look like in RS?
Didn't seem to be a problem on the test drive.
It may be that it is still a self-responsibility as long as the conformity is not indicated by Manufacturer.
I don't think you'll have to spend a lot of money on Ok.
View detail
The installation of the FrontCamera drrorecorder is very easy.
We have installed this product, which is compatible with the installation of Mistuba Sankoowa's EDR-21Gα drrorecorder.
I was planning to install Stubby on Front fork and put Camera on it, but Stubby is too expensive!
You made a Small leap of faith when you discovered this product. Even this one!
It comes with a mounting screw, but since it is very small, it is necessary to install the Camera in a quantity before installing it in the vehicle.:It is better to Set.
Attach the Bracket to the vehicle and then attach the Camera to the Quantity:If you set it, you will lose Screw.
I wanted to install it as Compact as possible, so I gave it 100 points.
I'm very happy with the way the Camera is mounted.
View detail
Items that make the installation of the Drarecorder Camera easier.
We have installed this product, which is a good match for the installation of Mistuba Sankoowa's EDR-22Gα drrorecorder.
I was initially considering one for the upper Right as it is from the Right Side that I get passed by cars from behind.
However, if you look at your motorcycle from the back, you will see that there is an exhaust system on the Right Side.
I bought the one for the top of the Left because I thought that maybe the exhaust air pressure might scare the Camera or make it dirty.
Since it is a moped, the width of the Number is Small, and the length of the Bracket is the same as 170mm, the Quantity:Pair (for Left and Right) You can adjust it, but if you shift it from the Center to either side, you can see the Bracket.
Bracket length could have been about 20mm shorter.
Also, it comes with a screw for installation, but it is too small to install the Camera with the Bracket on the vehicle.
Once the Bracket is removed from the vehicle, the Camera can be installed.
It has a good amount of wall thickness and is quite solid.
I'm very happy with the way the Camera is mounted.
View detail
Things are normal.
I chose it just because it was cheaper than the DAYTONA as a Camera mounting bracket.
The MiVue M760D from DAYTONA was installed.
The Bracket itself is strong and can be adjusted to slide sideways, so you can adjust the position of the Camera to fit your Motorcycle.
The angle was apparently level and the thing was a good product.
The following will be about compatibility.
After I installed it, I noticed that it was confirmed that Mistuba Sankowa and KIJIMA, which are basically used to secure Camera with Bolt, were compatible, but DAYTONA was not. (You don't notice it, right?)
The MiVue M760D's Camera is fixed with Double-sided Tape and In-Hemp palm mack, so it can only be attached with Double-sided Tape, and the In-Hemp palm mack could not be tightened because the seat surface is not square and could not be stopped. (Only the front side can be tightened if it wraps forcibly)
It is possible to use Double-sided Tape alone as it is not likely to cause any problems.
However, it is not a good match because the seat is long on the side and you can see the Bolt hole.
The color is Black, so it's hard to tell if you don't care, but if you are looking for perfection or are concerned about it, you shouldn't choose to install the MiVue M760D.
View detail
pre-cooking
I bought this because the Cook on the Tank no longer closes tightly.
The original cooker should be replaced or repaired, but I didn't have time, so I installed it as an emergency measure.
At any rate, it is convenient to have 1pc.
View detail
brembo installation
This is for the brembo brake.
The shape is good, but it interferes as it is, so I installed a part to shift 20mm from the original position, and finally I was able to install it without interference.
It would have been nice if the Tank fixed Bolt was also Black, but I had no choice but to paint the Screw Black to make it less noticeable.
I wish the selling price was a little lower.
View detail
I can take it off without it.
It's not easy to fit the Large.
It's not used very often, and it seems a bit of a waste.
Without it, you will have a hard time to spring with.
View detail
Fits: KAWASAKI ZX-9R, KAWASAKI ZZR1100, KAWASAKI ZZR1100, KAWASAKI ZXR400R, KAWASAKI ZXR750R, KAWASAKI ZXR400, KAWASAKI ZXR750, KAWASAKI ZZR400, KAWASAKI GPZ900R NINJA, KAWASAKI ZEPHYR1100
In Φ300
[How is it used?
Used in the OEMRotor300 era.
Silver, Compact and thick.
I didn't feel rigid anxiety.
Although the hole dimensions are provided, installation should be done with the Caliper on the side that it is going to move against the Fork outer during breaking and then bolt it in place.
Otherwise, the frictional force caused by the bolt tightening alone may cause the risk of gapping.
Was the one you received as per Image?
Yes
Was the installation difficult?
It's easy if you know the hang and the concept.
How was your experience with it?
OK
[Included Parts:were they on?
Yes, I was wondering if Shim was there.
[Was there anything that disappointed you?
None
View detail
It's not too obvious.
It's a Compact Bracket and it doesn't look so obtrusive.
I chose the Type that co-closes with the Mirror, and the Indicator is perfectly visible in this position.
I don't think the price is cheap, but it's less expensive than other products.
View detail
That's what I get for brembo!
I replaced the brake lever with a brembo brake lever, so I replaced it with this product.
The tank is a brembo OEM Smoke Type, so it gives a sense of ownership!
View detail
I've replaced it with a brembo Clutch.
I replaced it with this product because I replaced it with a brembo clutch lever.
If you swapped to a bremboClutch lever, you can't go wrong!
View detail
Can I use any Manufacturer's Camera?
It is a CameraExclusive Bracket, so I could install it on my Chinese Camera without any problem. I think it is good that you can choose for Right or for Left. View detail
I couldn't turn it on the GSX-S1000F.
In a small Space, you can use Filter. It did not. If you can hold it firmly with your hand, it will turn. I'm a little disappointed with my purchase. View detail
as one would expect
Well, it's just as I saw it, isn't it?
I think that I can put most Camera on the large size of the base of Camera if there is this much.
View detail
Generally good.
Purchased as a countermeasure against rust transfer to Concrete in the bicycle parking space.
Larger than expected.
When parking on gravel, the effect will be Large
It has a hole in it so you can attach a string to it and not worry about losing it!
If you look closely, if it is Yellow color, it looks like DonaldDuck?
View detail
high rigidity
I used it to install a Chinese Dr-Recorder and GPS Antennas along with Camera.
It's very rigid, so the Camera image didn't get blurry.
View detail
To change the Radiator fluid.
It is ideal for use when changing radiator fluid, as it can be inserted into the radiator body without the risk of it overflowing and spilling, allowing you to refill the radiator fluid efficiently. Of course, the Radiator Body can be folded into the Compact when not in use to change the engine oil. View detail
This is for the brembo master!
I fitted this Tank with a Kit to match my brembo CORSA Corta 17mm.
The vehicle is SEA BASSGSX-S1000F.
I fastened it to the upper side of the Mirror Holder and put the thin side of the attached collar between it and the Holder.
The other collar that comes with it is about 5mm thick.
Hose was settled in just right, without a cut.
It's black and has a unified feel, carefully finished and not cheap.
View detail