Reviews
Fits: MV AGUSTA F4 RR, MV AGUSTA F4 RC, MV AGUSTA F4 R, MV AGUSTA F4
Ah
Bolt is short, so I diverted OEM, but it's going round and round, and I don't know if that's right or wrong. View detail
Axle Slider
Easy installation, just insert and tighten up, but the instructions are not good and some washers need to be added to tighten up. Looks good. View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R, HONDA CBR1000RR-R SP
Bolt does not fit
Bolt is too long and cannot be fixed. I added two additional Washers to accommodate this. View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, TRIUMPH STREET TRIPLE 765 S, TRIUMPH STREET TRIPLE 765 R, TRIUMPH STREET TRIPLE 765 RS, TRIUMPH STREET TRIPLE S 660, YAMAHA MT-07, APRILIA DORSODURO 750, APRILIA DORSODURO 900, APRILIA SHIVER 750, HONDA CBR1000RR, KAWASAKI NINJA 1000, KAWASAKI VERSYS 1000, KAWASAKI Z800, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI ZX-10R SE, KAWASAKI ZX-10RR
Beautiful product
Lightech product is very beautiful with high quality product. Perfectly fit to my motorcycle. Good material, will repeat order again. View detail
Refreshing around the Rear
We chose this one because it was Reasonable price than other Fender Eliminator Kit.
First of all, when I first received the product, the holes in the Plate and Bracket did not match, and when I inquired about it, I was told that a different model had been included.
When I actually installed it, I had a hard time removing the OEMFender first.
There is no instruction manual, so I had to loosen the bolt and remove the parts, but there might have been some parts that I didn't have to remove.
The space under the Seat is narrow, so the Coupler for the lights is quite difficult to pull out.
Also, I used a small-sized MONKEY Wrench because the included nut was a size I don't usually use, but I think it would be more efficient to prepare a socket that fits the size.
As for the License Plate Light, I did not want to cut the OEM harness, so I purchased a Coupler that fits there separately and crimped the Bullet Terminal to extend the Cable, but the wiring of the attached License Plate Light is too thin. But the wiring of the attached License Plate Light is too thin, so be careful not to break the cable.
Colgate Tube was used for the wiring path and fixed to the Fender EliminatorBody with inHemp palmac.
The key cylinder of the Seat lock is screwed into the inside of the car body from the side. (I can't help but feel that the Seat lock release has become harder)
Speaking of the seat lock, the OEM dust-proof cover cannot be used, and the keyhole is exposed, so I think countermeasures are necessary.
I process thin rubber sheet and attach it with strong magic tape to make it removable and to prevent mud and dust from entering. (I've only run it a few times, but so far the keyhole is Large strong)
It took a lot of time to install the new product due to various modifications, etc., but it is a recommendation because it looks like a reflection.
(Although this will make the water splashing up behind the Fender a little worse.)
View detail
Fits: YAMAHA YZF-R7, YAMAHA YZF-R1, SUZUKI SV650X, MV AGUSTA F3 800, MV AGUSTA F3 675, HONDA CBR1000RR-R, MV AGUSTA SUPERVELOCE 800, BMW S1000R, HONDA CB1000R, HONDA CBR1000RR, KAWASAKI Z750, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z1000, KAWASAKI NINJA 1000, KAWASAKI VERSYS 1000, KAWASAKI ZX-10R, SUZUKI GSX-R600, SUZUKI GSX-R750, TRIUMPH DAYTONA 675
Good texture, good color, BALI is a charm.
I changed the OEM BlackCap to vulgar Gold.
I installed it at the same time as the POSH Faith Bolt cover Gold and the colors are similar, so it looks good.
There was some BALI left over, but there was no problem with the installation, so it is OK.
It is a Gold similar to the Gold of the Fork of the XSR900.
View detail
Fits: YAMAHA MT-07, TRIUMPH STREET TRIPLE S 660, TRIUMPH STREET TRIPLE 765 RS, TRIUMPH STREET TRIPLE 765 R, TRIUMPH STREET TRIPLE 765 S, KAWASAKI ZX-25R SE, KAWASAKI ZX-25R, APRILIA DORSODURO 750, APRILIA DORSODURO 900, APRILIA SHIVER 750, HONDA CBR1000RR, KAWASAKI NINJA 1000, KAWASAKI VERSYS 1000, KAWASAKI Z800, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI ZX-10R SE, KAWASAKI ZX-10RR
textured good feeling
I am satisfied with the texture and the color.
Installation is easy. It is expensive, but the impression from the side is quite different, so how about it?
View detail
Be careful of misconnections
[How is it used?
Installed on a 2022 MT-09 SP.
The OEMFender didn't look good and even if it did, it would roll up mud and dirt, so I decided to replace it with a Fender Eliminator.
Was the one you received as per Image?
It looked better than it does in the image, but it takes Sense to hide Wiring nicely.
I don't have that much Sense so if you look closely, it's rough.
Was the installation difficult?
1.Needs to be completely assembled from RoseRose state.
2.The instruction manual is in English version.
3.Overtorque needs attention because of tightening by Bolt of plastic parts.
4.Wiring for License plate needs wiring processing
The four elements of the system make it a little difficult for a novice maintenance person to install.
How was your experience with it?
I thought it was worthwhile to have it installed because it looks Refreshing compared to the OEM parts. Also, the small parts have the Manufacturer's logo, which I personally think is GOOD.
[Included Parts:were they on?
Three instruction manuals and, although not used this time, a mounting bracket compatible with external blinkers are also included.
[Was there anything that disappointed you?
As is often the case with MT-09 external Fenders, when replacing the OEM Product, the key slot for removing the Seat is exposed and dirt gets under the Seat. This product still has the plate, so I think it is relatively better, but it would have been nice if the lid of the OEM Product could have been used in the same structure.
[Availability and clarity of the Instruction Manual
Note that, because this is an overseas manufacturer's product, it is different from JapanManufacturer's product and is not written very carefully. Also, the assembly method varies slightly depending on the shape of the license plate in each country, so it is necessary to assemble the product while confirming the shape of the license plate.
View detail
Fits: YAMAHA YZF-R1M, YAMAHA YZF-R1, TRIUMPH STREET TRIPLE 765 S, TRIUMPH STREET TRIPLE 765 R, TRIUMPH STREET TRIPLE S 660, YAMAHA MT-03, YAMAHA MT-25, YAMAHA FZ1, TRIUMPH STREET TRIPLE 675 R, TRIUMPH STREET TRIPLE 675, KTM 125 DUKE, KTM 250 DUKE, KTM 390 DUKE, YAMAHA YZF-R7, YAMAHA YZF-R6, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA MT-09 SP, YAMAHA MT-09
Interference with Grip when installed as is
[How is it used?
OEM Bar Weight and Replacement
Was the one you received as per Image?
The color was a little lighter than expected and the fact that it was a split system was unexpected.
Was the installation difficult?
It was very easy as it was only stopped by one Screw.
How was your experience with it?
The feeling of use is neither pleasant nor burdensome.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
When installed as is, it interfered with the ThrottleGrip and prevented the Axel from turning. Since the inside diameter was 15mm, we used two 12mm M6 flat washers to lift the Axel.
Other items that would be helpful
Point of Installation
The pure Normal Thread Screw was an M6 screw, but this product is a countersunk screw, so care must be taken not to overtighten it, as it can easily lick.
View detail
Better looking than expected.
First of all, it is light anyway.
I would say it is less than half that of OEMs.
Installation is also by pon. It's as easy as pie.
However, it is thinner than the OEM, or it rattled when attached as is.
I put in Spacer and it's ok for now.
I will try various Spacer Materials. Let's start with pon.
View detail
Fits: DUCATI STREETFIGHTER V4 S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4 R, DUCATI PANIGALE V4 SP, DUCATI STREETFIGHTER V4, DUCATI SUPERLEGGERA 1299, DUCATI PANIGALE 1199, DUCATI PANIGALE 1199 S, DUCATI PANIGALE 1199 R, DUCATI SUPERLEGGERA 1199, DUCATI PANIGALE 1299, DUCATI PANIGALE 1299 S, DUCATI PANIGALE 1299 R FINAL EDITION, DUCATI STREETFIGHTER V4 S, DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4 R, DUCATI PANIGALE V4 SP, DUCATI STREETFIGHTER V4
A walking stick before you fall3
[How is it used?
We chose this product because we wanted to protect the Swing Arm.
I chose Red to match the body color and am satisfied with the color, which is ideal.
Was the one you received as per Image?
Swing Arm is more overhanging,
Protection is not complete.
Was the installation difficult?
A handling Instruction Manual is included, which describes the torque for tightening the fixing bolt.
I'm not sure if mine was an outlier or not, because the Left Side Bolt length is too short,
Fixed parts had to be machined.
How was your experience with it?
Unlike the Front, it rotates with the Wheel,
Easy to loosen, Locktite was applied to the fixed Bolt.
[Included Parts:were they on?
A handling Instruction Manual was included in the package.
[Was there anything that disappointed you?
The key Swing Arm cannot be protected.
View detail
Fits: DUCATI STREETFIGHTER V4 S, DUCATI STREETFIGHTER V4, DUCATI PANIGALE V4 SP, DUCATI PANIGALE V4 R, DUCATI PANIGALE V4 S, DUCATI PANIGALE V4, DUCATI SUPERLEGGERA 1299, DUCATI PANIGALE 1299 R FINAL EDITION, DUCATI PANIGALE 1299 S, DUCATI PANIGALE 1299
A walking stick before swallowing a fall2
[How is it used?
I was not sure whether to choose OEM Product or not, but I decided to choose this product to unify Rear and Manufacturer.
I chose Red to match the body color, and I am satisfied with the ideal color.
I feel it will protect the Front fork in the event of a fall.
Was the one you received as per Image?
I feel it is good without being too conspicuous.
Was the installation difficult?
A handling Instruction Manual is included, which describes the torque for tightening the fixed bolt, making installation easy.
How was your experience with it?
I thought it would be lighter than the BoltPierced Type ones,
The weight was there.
Plate tends to remain in the Axle Shaft when it is removed,
It takes a little time and effort.
[Included Parts:were they on?
A handling Instruction Manual was included in the package.
[Was there anything that disappointed you?
None in particular.
View detail
lightech frame slider
I purchased a frame slider to mount on R1.
I purchased it as a Lytech product.
It's good for shock absorption and I'm very satisfied with the design.
I think the quality is good and it's easy to install. I think it's good for decoration because there are parts that can add additional colors. -------------------------------------------------- -------- I bought a frame slider to be installed in Al -One. I bought it as a Litech product. It is also good for shock absorption and the design is so satisfying. The quality is good and it's easy to mount. There are parts that can add additional colors, so it seems to be good for decorating. Powered by Google Translator
View detail
Rytech Coloring
I purchased it as an option for the frame slider to be mounted on the R-One. You can add coloring to the inside of the slider, which is great for decorating your own bike.
The price was discounted so I bought it cheaply.
I am satisfied with the product quality and that it matches well with the bike. -------------------------------------------------- -------- Purchased as an option in the frame slider to be installed in Al -One. Coloring can be put inside the slider, so it was good to decorate your own bike. The price was also discounted and I bought it cheaply. The quality of the product is also satisfactory and it goes well with the bike. Powered by Google Translator
View detail
Good product with good design
I installed it on a 2014 s1000rr.
I bought it to use as a bar end mirror, but it is simple and blends in naturally with the design.
Installation is easy, just tighten 4 screws.
The quality is reasonable and I am satisfied with the product itself.
View detail
Installation is Large
No Manual etc., installation is tricky.
If the OEM bolt is used, it may crack with carbon, and flange bolt etc. must be purchased separately.
Also, the hole drilling is slightly misaligned, so it needs to be pushed in forcefully or some modification is required.
In my opinion, Magical racing”s Rear Fender Chain Guard integrated” would have been better.
And Rai TEC is about the same price to buy 3 Carbon parts around Rear except Rear Mudguard,
Magical racing Front Fender - I also had the manual when I purchased other parts. Above all, I have a sense of security in a domestic product.
View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10R SE, KAWASAKI ZX-10RR
10R SE Swing Arm Cover
I drilled a hole in the carbon cover to install it because it interferes with the chain guard, and the double-sided tape is not strong enough. View detail
looks quite eye-catching
I ordered Lightech tank pad to replace old Progrip tank pad on my Suzuki Hayabusa. The Lightech tank pad is easy to fit onto the fuel tank, stylish one-point, looks quite eye-catching. However the Lightech tank pad is much thinner than the old Progrip. View detail
Is this an inferior Chinese product?
I've read in the previous article that the Right can be managed by shaving a little (I used Grinder even if I say a little), but the Left doesn't match up! The first time I went to the store, I was told that I had to buy a new one, and that I would have to pay for the new one. View detail
Fits: DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 950 SP, APRILIA TUONO V4, APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 APRC, APRILIA RSV4, APRILIA RSV4 FACTORY, KAWASAKI ZX-10R SE, KAWASAKI ZX-10RR, KTM 1290 SUPER DUKE R, KTM 890 DUKE R, MV AGUSTA BRUTALE 1000 RR, TRIUMPH SPEED TRIPLE 1200 RS, TRIUMPH SPEED TRIPLE 1200 RR, TRIUMPH STREET TRIPLE 765 RS, KAWASAKI ZX-10R, HONDA CBR1000RR-R SP, DUCATI 848, DUCATI 1098
8BL-sc82 sp, did not come with 22 year MODEL
The shape of the OEM brembo cap reverse side and the reverse side of this product are obviously different, so I could not put it on.
The cap does not drop to the OEM position due to the protrusion on the reverse side of this product interfering with the cap on the inner side of the Reserver tank.
View detail