Reviews
incomprehensible
Instruction Manual is too complicated and difficult for beginners. I think some knowledge is necessary. View detail
Lightweight and Dressup
I installed the footpeg for the purpose of dressup after the removal of the footpeg, but unfortunately, I could not see the engraving, which is the most important part.
Other than that, I have no complaints.
View detail
Very good looking, but...
Pulling on the brake wire is important, but securing the rotating bracket is impossible with a screw lock, and the bracket inevitably moves. However, I think that a more ingenious bracket is needed instead of just using the OEM bracket. View detail
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
Change in appearance.
It is a self-satisfied part with no functional significance. View detail
The color is different from the picture.
I liked the design, but was a little disappointed that the gold was a strong orange gold! View detail
Quick wrench is discontinued.
Since the Rear Sets are also babyFace, I wanted to purchase the Filler cap in the same color as the same Manufacturer.
Cap has faded under UV light.
I also wanted to get a quick wrench, but I was told it was discontinued.
A quick wrench is not necessary because it can be removed with a Hexagonal Wrench without the need for a dedicated quick wrench.
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I'll never roll over …
I'm going to install it with the idea that it will look a little better before it falls down. View detail
Fits: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
Easy detachment!
Rather than a rear slider, the Axle Shaft was installed to make it easier to attach and detach the Axle Shaft.
It can be used as a handle like Doorknob when pulling out shafts, and when inserting shafts, the triangular pyramid shape makes it easy to insert the color, etc. without resistance.
Of course, it would also serve as a Slider, but currently it is benefiting from the detachment process.
View detail
Itchy!
I was having trouble finding a place to hang the Chain when removing the Wheel, but this is quite convenient because it serves as a ChainHanger. View detail
The smallest possible protection without compromising appearance
You won't know performance until you mock it up. View detail
Included Bolt
Please use Stainless Steel for the attached Bolt. View detail
Convenient for fixing
Convenient to fix with Tie Down when loading Touring net or TRANbo. No overhang is a concern.
It is also possible to continue using Tandem Footpeg without any problems.
However, the screws used for fixing (OEM diversion) are full of locks and are difficult to remove. Screw locks are necessary because they tend to loosen when reinstalled.
View detail
![[IDEAL] Frame Slider](https://img.webike-cdn.net/catalogue/11500/006-sk008_TS.jpg)
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1100
BabyfaceFrame Slider
The same Babyface as Axle Slider was used to create a sense of unity. View detail
Great product. Just wish they included another screw.
The design idea is great but they should have included another bolt for the right hand side of the shift spindle holder. Upon installation if you screw the right hand bolt too much it will bend the shift rod. I noticed this when casually screwing the bolt on and saw that when screwing it in that the shift rod started to drift to the right the more I screwed the bolt. I had to back off the bolt a bit as it started to bind the shift rod and was preventing proper shifting. They should have included another spacer so that the user does not accidentally screw the bolt to far. Great idea but missed the mark by not including another spacer. View detail
cb400sf nc42 late
I think the quality is very good.
The price of Plate alone is quite expensive. I wish they would at least add a footpeg.
As for the working aspect, it requires plate processing, which I think is impossible for beginners. If you have your own air tool, you can do it easily.
Footpeg was made by Speedra. This footpeg is well made and is a Recommendation. (For reference only)
View detail
AnchorPoint
The Tandem Footpeg was removed and installed since it is often mounted in the vehicle.
I am using it with KIJIMA's helmet holder, but I think I can manage to hang the belt on it.
The instruction manual says to use it only as an aid to deform it if it is pulled or tugged hard, which is not a problem because it is aluminum.
Dress-up parts.
The strength will be verified by using it in the future.
View detail
I'm glad I put it on.
I was skeptical at the time of purchase.
I bought it with the hope that it would improve my feelings.
Installation is not that difficult.
Please check when outside Rear Sets are used.
There is no difference in the Large size when entering Neutral at a stop, but the Shift feel while driving is completely different.
Snap and enter. It is not a feeling of softening.
It's like an increased sense of security that makes it harder to make Shift mistakes.
The difference can be seen when continuously SHIFT UP during acceleration or Downshift when entering a Corner.
Bearings are not bearing, so I think periodic lubrication is necessary
View detail
In the event of a fall
It is nice to have a component Single Body because it can be scraped off when tipping over. View detail