Reviews
Poorly finished
Unsatisfactory quality due to uneven paint and roughness.
Position is good.
View detail
WR250R Rikizo Slash guard
The installation is supposed to be car specific, but the pitch is not correct and the bolt is not bolted on. It took an hour to enlarge the long hole with a file. If you don't have the tools, you have to rely on the shop. It is a pity because of the price and thickness of the board. View detail
I put it on my TL125.
If you put it on as it is, it will hit the protruding threaded part at the bottom of the engine. In street driving
It is not inconvenient, but AttackTouring, the person who uses it like hitting the bottom is careful.
A little more consideration in bending would have been great. It's easy to put on, and the best
You don't have to remove the Guard when changing Oil, so this is 0
If the front side could also be guarded, it would be five stars. Currently, the place to fasten the back Bolt, Frame and
I put about 8mm Spacer between Plate. In this way, the bottom side of Case and
No more direct hits. 。 What is everyone doing here?
View detail
A little disappointed with the construction.
I installed it on my TL125.
It arrived and I immediately removed the old Under Guard and installed it, but there was one problem.
The bottom of the Crankcase hits the bulge of the Bolt. I tightened the front bolt.
The back Bolt is currently in a temporary fix. If you hit the corresponding part on a rock, the bulge part of Case will be damaged.
I think I'm going to break it.
The mounting holes etc. can be attached without difficulty. The position of the attached Rubber plate is not clear.
The rear plate screw comes with a long one, but does it mean that you should put something on it and float it? A little.
Lack of consideration. If the Under Guard you put on can't protect Crank, it's useless. The relevant part is
I thought it would be better if it was slightly bent and had clearance, and if the Right Side was a little wider.
I would have liked to have covered the protrusion of the Oil Filter part a little more.
If you want to drive on the street, there is no problem, but if you want to run on the slope, the installation is
Caution. As others have pointed out, the finish on the corners has a cut-off part, so you have to do it yourself.
I cut it, but be careful with the Oil ejection hole.
View detail
Fits: KAWASAKI KLX230, KAWASAKI KLX230S, KAWASAKI KLX230SM, KAWASAKI KLX230R S
OEM Product Quality
I'm 178cm tall and my heels float in the Normal seat, but in this Seat I can put my heels on the ground.
Since the vehicle is light, I don't mind the footing so much when driving on a relatively clean surface, but
The difference of a few centimeters is important for a beginner like me when it comes to a little hard mountain play.
The KLX230 has a higher seat height, but the minimum ground clearance is lower than the SEROW.
I bought this Seat because I thought it would improve my footing while maintaining the minimum ground clearance.
In that sense, I achieved my goal, but at my height, the bend in my knees is a bit painful.
(Still much better than SEROW, though.)
In addition, the feeling of being forced to sit in the concave part of Seat is strong where I was able to move back and forth positively if it was Normal seat.
The surface skin is also slippery with the same OEM etc., so you may feel that way even more.
Now I am back to Normal seat as I am used to Large minute vehicles.
After all, I can move the weight more positively with Normal seat, and I feel this is better when I get used to it.
Because this area is a place where there is a difference of taste even in the height and the usual use, it is that NORMAL was better for me
I would recommend these to anyone who is a little shorter or is concerned about their normal footing.
The low seat also makes the seat wider, so your butt won't hurt as much after a long ride.
Because the quality of the surface skin and Sponge etc. is also firm in NORMAL same etc., I think that it is a good product if it matches the purpose.
View detail
Fits: YAMAHA XT250X
I changed it.
When I changed Exhaust pipe to sp tadao, Heat Guard of NORMAL did not fit well and I bought it. It was necessary to expand the hole by rubbing to install. Is it because it is an exhaust pipe of the outside? I used some brains to put the Washer of the bundle into the back of Heat Guard, but installation is easy. Parenthesis became better at a glance! If you put in the carbon parts, it will change the look of the motorcycle a little. The performance is the same as NORMAL, and it doesn't have heat because it is carbon. I was wondering if it would be a good idea to put gold on the parts that get wound by rolling. I thought it would be a good idea to put gold on it, but I changed it and the parenthesis got better. View detail
Fits: YAMAHA XT250X
enigma
It's not what I was expecting.
I bought this stuff because I put a PowerBox on my serow 250carburetor.
The pitch accuracy between the screws was not good, so it could not be installed and the hole was expanded.
(Maybe the PowerBox isn't accurate enough.)
I'm more concerned about...
I looked at it when I installed it.
The bolt is in contact with the exhaust pipe or pushing it.
On purpose? Really?
Because it is uncomfortable, I cut the tip of Screw a little and install it.
I guess it's just cheaper than OEM.
View detail
Fits: HONDA Africa Twin(CRF1000)
just barely
I bought this because of the weak strength of the HONDA OEM Pannier (broken by standing moss)
It's a dedicated product and the construction is quite solid
Quantity for installation:Pair (for Left and Right) Quantity fixing Tandem FootpegBracket:You can remove the bolts of 2pc each and bite them in between Please note that it interferes with the Exhaust System and is a little difficult to remove
The Pannier Guard makes the Bolt a little shorter, but you can put it on properly
Now, I've actually installed it, but unfortunately it interferes a bit with the Pannier & hellip;I'm sure they're making the Pipe thicker to increase the strength …& hellip;
After installation, Tan Demar's legs cannot be lowered backwards, and it can't get into the car to touch the driver's legs at traffic lights, etc The heart is Down
It's not a cheap price, so you can at least put that kind of detailed design and bolts on it after the replacement I'm under the impression that it's okay … it's not
I hope I never get a chance to see it in action, but the product is well made
I'm just hmmm on the details
View detail
Forgding Measuring Cup quotient Product No : PC-00003
This force Measuring Cup PC-00003 is Material : It is Plastic's 30 cc Cup.
Fluid (Brake fluid) Approximate amount when swapping (30cc) I used it to divide it into Small.
In the case of Fluid, when working with the main lid of the can open, moisture in the air invades and it seems that it will react, so using this powered Measuring Cup PC-00003 several times I use it separately by pouring Small..
It is use of this force manufacturing Measuring Cup PC-00003 to the last as dividing to Small and simple as a guide, but since you can work while grasping the amount of Fluid you are using, you can carry out the work efficiently.
Also, since this capability Measuring Cup PC - 00003 has a lid, I can store O - ring and RingWasherGasket etc in a way not to be dented or scratched inside, or keep the Bullet Terminal terminal and Mini Flat Type Also useful for putting small parts such as Fuse.
This force Measuring Cup PC - 00003 contains Material : Plastic lid is attached and the lid closes tightly but I do not keep liquids thought by any chance.
Material : Since it is Plastic, it is not strong enough, but this powered Measuring Cup PC - 00003 is sufficiently useful as a 30 cc Measuring Cup and it is very inexpensive so purchase multiple items and make Small items etc etc etc etc. It is a very convenient container to classify it.
As for this mechanized Measuring Cup PC - 00003, it is inexpensive because it was lightly sealed so as to put a small thing in it, so this Measuring Cup PC - 00003 has a sufficient function as a Measuring Cup for small quantities As we are doing it will be a product of Recommendation in any case.
Moreover, it is a cheap product so it is very easy to purchase.
I made this power Measuring Cup quotient Product No : PC-00003 <Container Quantity : 2pc. I purchased Set>, but Quantity : 2pc. Set was a bit less, so I'm thinking about buying more on my next shopping.
This powered Measuring Cup quotient Product No : PC-00003 does not transform deformed even when used for Gasoline and its additives and engine oil as well as Brake fluid, and for Lacquer thinner and Parts cleaneretc. It is Measuring Cup which lasts long lasting Large even if it rinses with.
.
View detail
Can we go?
I thought that there were many opportunities to run rocks and galleys, and I chose the one with the thickest board thickness that I can purchase for XR 230. As expected there was only Manufacturer in Japan, it was not difficult to install. I will pray that you will try Guard after using it later. View detail