Reviews
Tightened with a slotted screwdriver.
Used to replace an oil line. It seemed to be able to close it with a hexagon, but it didn't fit slightly. I think it is a millimeter. View detail
Fits: HARLEY-DAVIDSON 3ΩCoil cars
Smaller processing may be necessary depending on the type of car and the type of coil.
Purchased this product as Ignition wire for BMW.
First of all, the length was long, but that was not a problem, because it could be cut off if it was too long.
The connection terminals on the Ignition coil side were simpler than those of the OEM, and the quality of the terminals varied.
I had no problem because I assumed that I would have to change the connection terminal, but I think that those who use it as it is should check it with caution.
Durability is still to be determined.
View detail
Fits: HARLEY-DAVIDSON Vehicles with OEM CVCarburetor
Minimum Quantity to Overhaul carburetor:Set
I used this for an under-seat engine hole on a 2000 XL883XL1200C SPORTSTER 1200. The vehicle had been immobile for a long time and the Carburetor rubber parts were hardened and leaking fuel. The beauty of this kit is that it omits the Float, DiaphragmRubber, and other parts, and only requires a minimum quantity of parts.:The Carburetor functions have been restored and I am generally satisfied, but the rubber packing of the Float chamber does not fit perfectly and I am not able to assemble it. View detail
Fits: HARLEY-DAVIDSON Fits OEMCVCarburetor
No installation problems after a little sharpening.
The surface treatment of the slide valve seems a little rough, the OEM was the same, so no problem.
Because the negative pressure presses the Slide surface Rear against the sidewalls, especially the areas that are strongly hit are polished and shining.
If the corners and flat surfaces of the PAL blade wings are polished with a gold-based polishing compound and installed, the initial sliding will be smooth.
View detail
Purchased to match fuel economy.
I bought it to match the fuel tone.
I have purchased several different types to start setting and I recommend them for their quality!
View detail
Purchased to match fuel economy.
I bought it to match the fuel tone.
I have purchased several different types to start setting and I recommend them for their quality!
View detail
For fuel setting.
Used for fuel setting.
I have purchased several kinds of products and they are of good quality and Recommendation.
View detail
Fits: BUELL All vehicles 91- (except 1125R), HARLEY-DAVIDSON SPORTSTERFamily
To remove the Primary.
Used to remove Primary.
It is rather expensive but easy to use.
View detail
Indicator bulb out of service.
It was used due to a broken bulb in Indicator.
It's working fine
View detail
Fits: HARLEY-DAVIDSON Universal
The longer it is, the easier it is to see!
I couldn't see the short Type's so I bought the long ones.
Easy to see!
View detail
Fits: HARLEY-DAVIDSON Universal
It is almost invisible.
If you are only looking at it, you will be satisfied, but not as a Mirror.
You have to twist your body to see behind you.
View detail
Used for fuel setting
Used for fuel setting.
I have purchased several kinds of products and they are of good quality and Recommendation.
View detail
On a ball run out.
I bought this for replacement because the bulb was out!
It was fixed normally!
View detail
Fits: HARLEY-DAVIDSON Universal
Select a car model
Considered UnderMirror and purchased for a slightly different application.
As a result, the length did not match.
If there is room in the Handlebar and Tank, such as a lightweight Off car, it could be done.
I might have opted for the other longer one.
View detail
Because of cheapness?
Mokumoku when running on a pouring day.
A little fun with steam.
The color fading is great, perhaps due to the cheapness of the product.
Large might be sturdy if wrapped in a double layer, but
Space-wise, it's tough.
It would be stupid to rewind it just for the color.
As far as looks go, it will be White in a few months.
Consumables.
Color:Gray, Black, at least not this white.
I'm wondering if anyone knows of a product that says it won't fade.
I'd like to know so much ….
View detail
It worked for now.
At least it worked for now;
I am concerned about how far it can be used.
I hope it is Large sturdy…
View detail
Fits: HARLEY-DAVIDSON Most Harleys with stick footpeg
Good product, but a bit of a hassle to install
I installed it on a 1998 xl1200s.
It is easy to use and does not slip, but I had to cut it down a little to install it parallel.
It may be an individual difference, but it took a lot of effort.
View detail
The exchange is Large!
This is a pure product replacement.
The accompanying information, such as "You will need this," is included.
I wish they sold liquid Gasket and silicon grease at the same place.
View detail
It works well enough!
As a meter bracket, it is inexpensive, but it is useful enough. View detail
Fits: BUELL All vehicles 91- (except 1125R), HARLEY-DAVIDSON SPORTSTERFamily
It's solid
I bought the special one in advance so that I would not have to worry in case of a breakdown. It is expensive but well made. Cost performance is not good. View detail