Reviews
Poor return of Engine Starter Motor
After a year and a half of use, the return of the Engine Starter Motor was poor and the CellMotor kept turning.
The same thing is written in the review of KIJIMA's Engine Stop Switch, so things seem to be the same.
For now, I did a Silicon spray and it came back, but I'm sure it will reappear after a while.
It is inexpensive, so let's just use it as such. (Laughter)
View detail
![[Bar End Repair Parts] Flat Washer](https://img.webike-cdn.net/catalogue/images/22383/031076-72_01_TS.jpg)
Just a Washer.
It's just Washer.
It is just a Washer with 22mm OD, M6 hole, 1.6mm thickness.
I said it twice because it is a Large thing.
We had no choice but to purchase the Bar End because the part in question, which had been stocked, had gone missing.
It may seem that Large is sturdy without it, but in fact, if it is not installed, the Bar End may easily fall off, cannot be firmly fixed, or may interfere with the Throttle.
So it is practically an indispensable component.
It's just a Washer. (Lol)
Considering the price, if you have the time, it is much cheaper to buy the same Size at Home center.
I didn't have Timing to go buy it, so I bought it on webike.
View detail
Separate handle makes it difficult to see the upper rear side.
With the separate handle, it is difficult to see the upper rear side even if the mirror surface is adjusted to the fullest extent. View detail
It may not fit in Separate handle.
With a separate handle, even if the mirror surface is turned fully upward, the upper rear side is difficult to see. View detail
The finish seems to be a bit of a mess….
The product is for SR, but I bought it to divert it to another car model.
I decided on this product because it is processed with a long hole and the height of the stopper seems to be adjustable, but I have to say that the processing is very crude.
The treatment of the long hole is also terrible, but there is also a Gap between the top and bottom holes. With this Level, I should have gathered the components and fabricated it by myself.
View detail
Not for use with Stainless Steel Hose
I have a Stainless Steel Hose from Swage line and could not use it due to interference.
I could have used it if it had been directly below without the odd Offset...
I think the OEMHose is SMART and easy to install.
View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z250, KAWASAKI NinjaZX-25R, KAWASAKI NinjaZX-25R, KAWASAKI ZZR1400, KAWASAKI ZZR1200, KAWASAKI ZZR1100, KAWASAKI ZX14R, KAWASAKI ZX10RR, KAWASAKI ZX10R, KAWASAKI ZX-9R, KAWASAKI ZX-7R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1100, KAWASAKI ZEPHYR1100RS, KAWASAKI ZEPHYR1100, KAWASAKI Z900RS, KAWASAKI Z800
My hands were numb because it was not Rubber mount.
I replaced the OEM with this one, even though it has Weight.
My hands were numb because it was not Rubber mount.
Bar End of Other Brand Product is made like this in Large size.
I have been looking for a product that is heavier than OEM and has a rubber mount, but so far I have not found one.
View detail
Durability..
1st purchase - Bulb expired in approx. 1 year.
Second purchase - Bulb expired after 1.5 years.
It looks good, but not with this durability.
View detail
usually
The texture is normal and a bit expensive for a Mirror filler. View detail
high
I bought it because I made a bar end mirror.
The handlebar is black, so choose black.
I think it's a very expensive product for the price.
Easy to lick when installing and removing with a slotted screwdriver
Don't put too much pressure on it, it will lick you in one shot.
SmallParts, but it's Exactly after Mirror.
Next time I won't buy it.
View detail
Problems with length and Nut.
First of all, the length of the opening side and the closing side is different by 3cm, but I don't understand the meaning of this difference in length no matter how I install it. It's a pity that the bolt for Throttle side is 13mm head. This is not good. View detail
Difficult to keep up with
Installed on a '17 CRF250M
This is the corresponding Relay, which is essential for the LED Blinker to flash properly. Since it has been taken care of in almost all the car models that I have ridden until now, there is no problem in the performance that is required.
But the size is bigger than OEM Relay. It may be difficult to fit in some car models.
Since the wiring is longer than the OEM and the connection coupler is universal, the OEM waterproof cap may not be able to protect the water. When driving for a long period of time in the rain or in large rain, the flashing abnormality caused by the leakage occurred in both current and past models.
It returns to the original state when it dries, and it is possible to protect it with WaterproofGrease etc., but it recurs when I forget.
Of course, there were some car models that had no problem, so it's hard to say, but... I hope this helps.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
Mmm.
I put it on my current NINJA400, but the angle is not level because it is installed in the mirror hall of Handlebar, and the inside is facing up, so when I install a smartphone or Beeline Moto, the screen is facing outward and I can't see it unless I look into it. The design and color are good, but from a functional standpoint, I'm not happy with it. View detail
Is the luminescent color Red?
Blinker lens. [Color] I thought about purchasing the Orange color Valve because I chose Clear. I bought this product of coating so that it may not stand out, but the S bulb is no problem, but the W bulb's luminous color is like Red and the brightness is dark, and I decided to use the Orange bulb of the company. View detail
This is the first Mud Guard I put on.
I finally settled on HURRICANE's Mud Guard, but before that, I bought this one and put it on.
I thought it looked good, so I put it on …
good point
The thin aluminum board is stylish.
Easy to install with the Tie Wrap.
I can cover small stones to some extent.
A bad point
Stylish is fragile and contradictory.
The Tie Wrap broke easily and fell off the body.
The Mud Guard I bought was cheaper and stronger than the Mud Guard.
It may be wrong to ask for strength in the installation of Tie Wraps, but I think it is safer to use a manufacturer that specializes in Gold Parts, if it is a Gold Part.
To each his own, though.
View detail
Design is good, but build quality is…
Quantity:Pair (for Left and Right) I installed it on my SR400, but after 2 days of installation, the mirror surface started to move with the vibration of the motorcycle.
I bought it after I was troubled by bad visibility in terms of short mirror, broken arm by vibration of SR, refreshing and simple design, relatively affordable price, and considering good and bad points. I've been riding it only for commuting.
It's a shame because the Design was well suited to the Separate handleSpec.
View detail
Fits: HONDA CBR600F, HONDA CBR1000RR, HONDA CBR600RR, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 Super Four, HONDA CBR954RRFire blade
Replaced with LED.
Because the phenomenon that the License Plate Light flickers in synchronization with the blink of the Blinker occurred, LED was carried out.
The flickering of the License Plate Light has been eliminated by changing to LED.
I also replaced the Relay with the enclosed Relay, but after using it for about 3 months, the Position lamp and Quantity:Pair (for Left and Right) Blinker and Hazard lamp don't light up at all anymore. Is this a durability issue? It's a shame because they blink beautifully.
View detail
Repair cosmetic scratches with oil-based Magic
The design and construction of the product itself is good, but there is a mark that looks like a cosmetic scratch was Repaired with oil-based Magic. View detail
Fits: KAWASAKI NinjaZX-25R, KAWASAKI NinjaZX-25R, KAWASAKI Z250, KAWASAKI Z900RSCAFE, KAWASAKI NINJA650R, KAWASAKI NINJA650, KAWASAKI NINJA400R, KAWASAKI NINJA400, KAWASAKI NINJA250R, KAWASAKI NINJA250, KAWASAKI NINJA1000, KAWASAKI GPZ900R, KAWASAKI GPZ1100, KAWASAKI Z1000, KAWASAKI Z250, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI Z900RS, KAWASAKI ZEPHYR1100
Excellent sense of gravity
There are many kinds of Bar Ends, but Posh's Ultra Heavy Bar End is as expected in terms of weight and design. However, when you install it on DAEG, Screw lock is working well, so it is impossible to use Driver. View detail
Request for return
This is a CF POSH tail lamp, but the product I received had no evidence to identify it as a POSH product. Normally when you buy a product in a shop it comes in a Manufacturer's package, but this product was just wrapped in a Nylon bag and in a suitable box. There was a Seal on the box, but no POSH name, nor is there any stamp on the product.
I haven't received a reply yet, although I have submitted a return request as I don't have any proof of manufacturer.
If you are unsure, you should avoid buying it. If it's made inexpensive mid-0, it's Shock.
View detail