Reviews
Easy to apply.
I've used Decal from various manufacturers, but the ease of application, thickness and shape of the material are all at a very high level. If you use a spatula and a little detergent, you can adjust the position and remove the air. View detail
It makes a different impression.
The size is a little small.
It's about 3mm smaller than Fender.
The WR Fender is quite uneven, so it needs to be applied with heat, and since it is a thick Decal, it cannot be applied properly with water.
Apply heat from the center, and paste while stretching, but if you don't match the center exactly at first, the gap between the edges will not be even when you finish pasting.
I drew a line on the center of Fender and Decal with oil-based Magic and put them together.
Finally, use Parts cleaner to remove Magic and you're done!
Be careful not to apply too much heat or it will turn white and overstretch.
View detail
Graphic, shape and details are OK
Thank you very much for the quick delivery after ordering. Our MotorcycleTire is made by MISSISIULAAN, and we thought we would adhere to the purchase Sticker. The location is TankSpace, and I think it will be unique. I like it. View detail
Fits: HONDA CRF250R, HONDA CRF250X, HONDA CRF450R, HONDA CRM250R, HONDA CRM250AR, HONDA XR250, HONDA CR250, HONDA CR125
It's so cool!
CRM250RR (MD14) The speedometer cable fixation part of RightFork Guard needs to be cut, but it is cool and it is Large satisfaction. View detail
Seat Replacement beginner friendly!
Reason for purchase
The normal seat has a hole in it and it absorbs water.
I bought it to deal with the Urethane inside as soon as possible because it was going to be torn apart.
I was hoping it would be sooner than later because the actual hole was 2017WAX old man.
Three years have passed.
Reupholstering work
First of all, I'll briefly explain how you will perceive it depending on your experience with reupholstery.
I'm new to reupholstering, I've reupholstered twice in Total.
1st time... WR250XNormal Seat Cover was peeled off once, and Normal Seat Cover was reattached again by shaving the Urethane of NORMAL in the low footpegSeat style (Manual Tucker).
2nd... KLX125SPIRAL High Seat Replacement... Because there was animation, this was referred to, but because Spec. of Seat cover had changed, because it made a slight mistake and redoed several times, the hole of Tucker has been vacant for a lot of failures. (Air Tucker)
The reupholstering process began as anxious as ever.
You will need to adjust the air pressure and the specs of the tucker bullets, etc. because we used the Air Tucker this time.
If the air pressure is high, it will punch out the seat cover, and if the legs of bullets are long, the legs of bullets may come out on the surface where the urethane of both sides of Seat is thin. We recommend you to check the spec. of Air Tucker when you purchase it because some of the Air Tucker's spec. cannot be used with the legs less than 10mm in length.
The bullets used in the OEM were 3-4mm, I believe.
When the adjustment is finished, temporarily fix the upper and lower Quantity:Pair (for Left and Right) Tucker to the front of the Seat.:Pair (for Left and Right) in turn stopped towards the back.
If the sagging occurred, I pulled it back again from where it had returned slightly and stopped it.
However, I punched out two parts of the seat cover due to the air pressure adjustment failure and the blank shot.
Quantity every time:Pair (for Left and Right) It was a Large oddity to pull on the even etc. and also to pull on the front and back without any slack.
The Seat coverBody is different from the previous models in that there is quite a bit of room between the place where you hit it with the Tucker and the place where you pull it with your fingers, and it was quite easy to pull it.
Effects
I haven't ridden it in bad weather, so I don't know how well it works in extreme conditions.
On normal courses and riverbeds, the Grip is frankly better than the Normal seat.
When I tightened Seat with my thighs on the climbs of the gully and the steep climbs at Standing, it was hard to move backwards.
I had to use my arms to hold on to my body as it was being taken backwards, but the rate of that was reduced and the Stamina in my arms lasted longer.
Current state
The current state is not slippery enough, but I wanted to add a grip on the shape of the seat cover in addition to the grip on the material.
View detail
Just a good Size
It is a sticker with a simple design that can be put up anywhere. View detail
Carbon Fork Decal
Factory effex Decal is a perfect The quality is high for an inexpensive . The glue is solid, the accuracy of the cut is pretty cool and very easy to paste View detail
Used for Repair in Decal
The manufacturer's graphic decal used on the off-road vehicles has deteriorated over the years of heavy use.
The edges and corners have come off.
I would reupholster the same Decal if I could get it, but it has been discontinued and is no longer available.
This product was originally intended to be used for the Back of the Number Plate part, but
Since it is a product of the same manufacturer (3M) as Graphic decal, it is also a
When I used it for Repair, I was able to repair it beautifully without any discomfort.
View detail
Factory effex is good.
Factory effex Decal is a good outing. The quality is high for an inexpensive price. The glue is solid, the accuracy of the cut is good, and the surface [Color] The Clear layer doesn't come off either. It's better to use the standard soapy water when applying it when you're not used to it, but once you're used to it, go without the soapy water. First of all, peel off the center of the backing paper (by tearing off the backing paper) without removing the whole backing paper. Then you can peel off the backing board gradually from the center to outside for positioning. However, you need to use the Dryer for dust alignment. Dryer is easier to use. It's better to leave the glue on for 48hr or so until it stabilizes. View detail
Let's just say it looks good
I thought I was lonely around the Rear, and bought it for Sticker But the white part is not cut out around the letters, so the white part stands out I had to cut it out in my own way this time, too I want you to cut it out from the beginning if you can It's difficult to get a price View detail
Size is Smaller than I expected
I bought a new exterior for my WR250F
Each one is rather small, so it was not very noticeable
However, I think it's a very good one as it shows no signs of peeling off at all, even in the rain
It was perfect if Size was a little bit more Large Sticker, but &hellip ;
View detail
Change Large to Knee
My car is Yamaha YZ125X
I felt a large change when I was standing and cornering It feels solid!
It will stabilize your buttocks!
These are the items I'm glad to have added
The Seat cover of NORMAL is not peeled off as it is, but covered it from the top and stuck it There was no problem to do
There is a sense of security that allows you to return to NORMAL at any time (^^)
View detail
Best
The product is in good condition, the design and shape is good, the size is creative and Exactly, but not yet I'm trying to figure out where to put it on the MONKEY125, how strong is the adhesion? View detail
Good for Helmet
White color Helmet of YamahaYJ-17 is lonely, so I put it on the rear The size is also good because it is a red and white color combination sticker The gold amount is also good View detail
Recommended for Wound prevention
installed on my crf250 RALLY50 Just in case of stepping stones or mossy forest road The impression of the product changes after installation The product is very thick and works well for Wound protection I had to reapply it several times because it was misaligned, but after 6 months of use, it just peels off a little It's going to last longer if you don't reapply it, not the side stand To work on the body of the vehicle with MaintenanceSTAND, etc Recommendation View detail
Fits: HONDA CR125, HONDA CRF450R, HONDA CRF250X, HONDA CRF250R, HONDA CR250
Good design
We think it's good-looking and refined in terms of design
I'm glad that the COST is a little less expensive, if there are any more cheap ones
We look forward to the efforts of the manufacturer in the future
View detail
The color is different from the photo
The shade is orange, not yellow Also, the edge is not white, but clear
I wanted a white edge with yellow letters, so I used the Image It's a shame I couldn't do Custom
View detail
The white part is thick, so there are only a few places to put it
The white part around the letters of HRC is too thick The white part of the Cowl is too thick, so I was very surprised when I received it It's not noticeable, but if you want to put it on something else, you might as well cut the rim It's a cheap product and I'm satisfied with it View detail
Fits: HONDA CRF250 RALLY, HONDA CRF250M, HONDA CRF250L
My First Seat Replacement
It was the first Seat Replacement, or temporary fixation & rarr; a few times for the main fixation Repeatedly, it installed beautifully with no deflection
The quality is very good and will last a long time! (^^)
The bottom line is that Grip AllGrip It is only claimed to improve RidingControl with a good grip (^.^)
ThailandHonda OEM's BlackSeat and SpiralSeat cover and I was hesitant to buy it, but I thought the grip power, material, etc.. I think (^ ^)
View detail
Tighten up around the Front
White, Black, and Red colors are used to match the motorcycle body color I think you should
The thickness of this product is sufficiently thick, so it is very strong and high-grade, unlike ordinary Decal
The monochromatic Fender is tightened up
Fender is substituting the CRMAR for the CRF250 that I bought at the same time (To Fender
Because of the step, Rear's Bolt is 2cm longer than OEM and has an 8mm inner diameter (Fixed with Aluminum collar)
View detail