Reviews
Fits: HONDA CBR1000RR, HONDA CBR600RR
Lever replacement for CBR600RR
[How is it used?
City Riding ~Touring
Was the installation difficult?
Instruction manuals are also available and are extremely easy to follow.
How was your experience with it?
I am up to my ring finger when I use it, so Short is just fine and easy to use.
[Was there anything that disappointed you?
It is not so much a disappointment, but even if the Lever is matted, the Attachment section will be glossy. It may bother some people.
I was not sure whether to choose Blue or Silver for the Adjuster, but I chose Silver because of its harmony with the Bolts around the Handlebar. Personally, I think it was the right choice.
There are six levels of adjustment, but please note that fully locking the handlebar to the furthest position will cause partial interference with the vehicle body.
As a note on installation, I don't think the Instruction Manual mentions it, but it is recommended to apply grease to the areas where the gold elements rub against each other.
Since there is vibration around the handlebar, we also used a screw lock agent to prevent the screws from loosening.
View detail
Fits: HONDA CBR1000RR, HONDA CBR600RR
Appearance and operability
[How is it used?
City Riding ~Touring
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
Instruction manuals are also available and are extremely easy to follow.
How was your experience with it?
I am up to my ring finger when I use it, so Short is just fine and easy to maneuver.
[Included Parts:were they on?
I don't think there are any missing items.
[Was there anything that disappointed you?
It is not so much a disappointment, but even if you choose the matte type, the Attachment part will be glossy. This may bother some people.
Although not specifically mentioned in the Instruction Manual, it is recommended that grease be applied to areas where the gold species rub against each other.
Also, the handlebar section is subject to strong vibration, so a screw lock agent was used just in case.
Note that when the Adjuster is expanded to the maximum Large, some interference will occur. 5 out of 6 levels are Large sturdy.
View detail
It's a shame because the quality is good.
The problem is on the Brake lever side, where the SensorSwitch that turns Cruise Control on and off is not pressed in enough to use Cruise Control. It is a pity because the quality is good. View detail
good
looking good but its for light use not for hard rally use as its just plastic guard . will definately buy one with metal frame next time View detail
Fits: KAWASAKI KLX250, KAWASAKI KLX230SM, KAWASAKI VERSYS-X300, KAWASAKI VERSYS-X250, KAWASAKI KDX125SR, KAWASAKI D-TRACKER X, KAWASAKI KLX300SM, KAWASAKI KLX300, KAWASAKI KLX230R, KAWASAKI KLX230R S, KAWASAKI KLX150S, KAWASAKI KLX230, KAWASAKI KLX150BF, KAWASAKI D-TRACKER125, KAWASAKI KLX125, YAMAHA XTZ125, YAMAHA WR155R, HONDA TRAIL125, HONDA CRF150L, HONDA CRF250M
Satisfied with high quality and functionality
I installed it on my CT125.
The OEM felt the need to replace it with Other Brand Product since the grip is not adjustable, and selected 3Finger from the stable ZETA.
Since I had already used it on another Motorcycle and was satisfied with the comfort of using it, I did not consider choosing from another Manufacturer.
The grip and feel of the controls are now much better, and I realized once again that you have to choose good quality parts for parts that are always in contact with each other.
View detail
Fits: HONDA BENLY50110, HONDA BENLY50110, HONDA BENLY50, HONDA BENLY50, HONDA GYRO CANOPY, HONDA GYRO X, HONDA GYRO X (GYRO X), HONDA GYRO X (GYRO X), HONDA GYRO Up (GYRO Up), HONDA GYRO Up (GYRO Up), HONDA GYRO Up (GYRO Up), HONDA GYRO Up (GYRO Up), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY), HONDA GYRO Canopy (GYRO CANOPY)
It's a good product
It is being used well as a replacement for the genuine Benley 110.
It fits well without any discomfort and the operation is no different from the original.
This is a satisfactory product at an affordable price.
Although this is unlikely to happen, I am willing to purchase this product again if it breaks. You will never regret it. -------------------------------------------------- -------- It is being used well as a replacement for the genuine Benley 110. It fits well without any discomfort and the operation is no different from the original. This is a satisfactory product at an affordable price. Although this is unlikely to happen, I am willing to purchase this product again if it breaks. You will never regret it. Powered by Google Translator
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Minimoto MONKEY Handlebar Clamp
I purchased this product because I replaced the 6V OEMMONKEYFront fork with a 6V GORILLA, and I wanted to install the HURRICANE Mini condor that was attached to the GORILLA, but I knew that the for MONKEY Top Bridge cannot be attached to the GORILLA's Handlebar Clamp, so I purchased this product. I decided to purchase this product because the position and diameter of the mounting holes of the Top Bridge are different between MONKEY and GORILLA, and the price is reasonable. When I installed the Handlebar Clamp, the position of the Handlebar was about 10mm forward, so I can use it without any problem. View detail
Fits: KAWASAKI KLX250, KAWASAKI KLX230SM, KAWASAKI VERSYS-X300, KAWASAKI VERSYS-X250, KAWASAKI KDX125SR, KAWASAKI D-TRACKER X, KAWASAKI KLX300SM, KAWASAKI KLX300, KAWASAKI KLX230R, KAWASAKI KLX230R S, KAWASAKI KLX150S, KAWASAKI KLX230, KAWASAKI KLX150BF, KAWASAKI D-TRACKER125, KAWASAKI KLX125, YAMAHA XTZ125, YAMAHA WR155R, HONDA TRAIL125, HONDA CRF150L, HONDA CRF250M
BrakeTouch is also improved
I have used it on my KLX230R and it does not break the lever even after repeated falls, and the touch of the brake lever is improved over the NORMAL, so I installed it on my CRF250L as soon as possible.
With the NORMALLever, when I apply the brake, it feels unreliable or squishy (which is natural since it is an off-road vehicle), but with this lever, I feel that the ease of levering and the construction of the lever improves the touch and makes it easier to control the brake. I think it may be because the lever is positioned closer to the car.
Installation is easy since all you have to do is remove the Bolt and replace it with a NORMALLever, but it would be easier to work with if you loosen the Mirror Holder and change its orientation.
When replacing them, it is better to grease them up properly before replacing them.
View detail
About HuOakDamperKit
Without recognizing what would be the HuOakDamperKit
I got it by mistake, but I'm not in a position to confirm the effectiveness of the installation yet, but will in the process of using it in the future.
I was puzzled by the fact that no explanatory material was included in the package when I received it.
Instruction Manuals are also available from other manufacturers at a lower price than this product.
please take good care of it
View detail
Genuine SP Takegawa Master Cylinder Lever for Honda Monkey 125
I specifically purchased this Kitaco lever as it is a billet one and not a steel one that came on the bike. The customer wanted a billet lever as a replacement anyway due top asmall fall and the lever got scratched pretty badly. I looked a t a few other brands but finally found that SP Takegawa did a cracking deal on this lever so in my basket it went. It was not really hard to find as I just used the search on Webike for this model and narrowed down categories. For what this is actually made of the price was slightly reflected in that but still, really good value from a great brand. With some other parts, my order was shipped using EMS and arrived in 5 days. The lever did comae in the SP Takegawa packaging and was well protected. The design is flawless and a really good take on a classic lever pattern. As this is billet, it is made from one piece of aluminium and you can see that in the lever. The quality is really stunning. A lovely smoothed out surface with plenty of meat on it so it will not break easily. Fitting this to the Monkey bike was just a matter of unscrewing the pivot bolt and replacing the lever. Nothing hard at all. It did surprise me but the lever once fitted does feel like it belongs on the bike anyway. The action is smooth and no notchiness. Very pleased with this purchase. View detail
Fits: KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z900 (KZ900), KAWASAKI Z1000 MkII, KAWASAKI Z750FX, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900), KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750FX
I purchased this for an external Stemfor replacement.
The quality is fine and well made. View detail
Fits: HONDA CB223S, HONDA CB400SS, HONDA FTR223, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, KAWASAKI 250TR, KAWASAKI W400, KAWASAKI W650, KAWASAKI ESTRELLA, SUZUKI ST250, SUZUKI ST250 E Type, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI VOLTY, SUZUKI VOLTY, YAMAHA DRAGSTAR250, YAMAHA SR400, YAMAHA SR500, HONDA REBELUp half-wheel* with AMALThrottle
Changed from a bifurcated Wire type for independent Carburetor
I bought a battered 900SS (900SL) and am Restore.
The FCR Carburetor Body is used for the carburetor, but it is not a two-cylinder one, which is often used in car-specific kits, but independent for the front and rear cylinders.
(Independent Carburetor is designated because the radical Camshaft has teamed up with)
For Independent Carburetor, generally comes with a Car Model Kit Throttle Wire branched in the middle." is commonly used.
It is normal to have two branches and four wire ends because they are used for the open and closed sides, respectively.
That's how I used to do it.
To be precise, the Reverse Side was removed because of the poor Throttle Fee Ring, and only the Open Side was used by maintaining the smoothness with frequent maintenance.
The fee ring has been improved considerably since it is only on the open side, but there is still a branch joint in the middle of the ring, and it lacks directness.
To overcome this, we prepared this Wire to pull each Carburetor to Direct.
Wire itself is quite normal, nothing special to say.
If anything, the middle Joint is Material:I'm glad it's Stainless Steel, because I don't have to worry about Rust.
However, there is a bad part, the molding shape of Thailand is a little rough...
Of course, it is not unusable, and there is nothing wrong with using it as it is, but it is not a problem to use the bean-jam-filled wafers. (Monaka) I am concerned about the raised areas of the mesh that were formed by the matching process.
Since the thailand part may rotate slightly at the beginning of opening or just before full opening, the round thailand part will improve the fee ring at the very small opening angle.
I used File to round it out before I used it.
Even if the fee rings are not affected, the thailand coils without any snagging are easier to maintain.
Also, there is no coated tube inside the Outer tube.
It is a Wire configuration with no features whatsoever, consisting of Spiral Tubes made of the old-fashioned Gold genus.
So the first lubrication is a Large thing.
Without oil, the feel will be rough, and with high viscosity oil, it will be sluggish.
On an FCR Carburetor Body with the Reverse Side removed like mine, it is fatal and life-threatening not to be able to spackle back.
This is not limited to this Wire, but try it often before lubricating with the best Oil.
View detail
Fits: KAWASAKI ZX-10R, HONDA HAWK11, KAWASAKI Z1000, KAWASAKI Z1000R EDITION, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI NINJA1000, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR SP, HONDA CBR1000RR SP2, HONDA CBR1000RR-R, HONDA CBR1000RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR CONCOURS 14
high quality
[How is it used?
I got a VTR1000SP2 from an acquaintance that had been neglected for a long time, and the lever was not OEM, but a cheap type of machined type that looked a little weird when you held it.
I don't like it, it's on Short and I don't like the way it feels against my finger. If I liked it that way, the OEM lever would be that way, and motoGP has that on theirs. So I thought about going back to OEM, but since I usually play off-road, I chose ZETA.
I chose it because it is not a so-called dress-up shape.
We chose this product because our VTR1000SP2 has FrontSection replaced with SC59 CBR1000RR.
Was the one you received as per Image?
The quality of ZETA's sharpening has improved over the years. In the past, the anodized surface would fly off and peel in seconds, but now it is Large and durable.
How was your experience with it?
It is easy to grip and the adjustment mechanism is fine-tuned.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If you are a gutsy person who wants to use Remote adjuster, you can buy Flight lever on a top ranking.
View detail
Not a Kit Part
Mounting Hardware is defective even though it is a Kit part.
Unable to install on current vehicle (ct125 CT110 HUNTER CUB)
Product Contents do not conform.
View detail
Fits: HONDA CB1100, HONDA CBR1000RR, HONDA X4, HONDA VFR1200F, HONDA VFR800, HONDA VTR1000FVTR1000F FIRESTORM, HONDA CB1000R, HONDA CBR1100XX SUPERBLACKBIRD, HONDA CB1000 SF (Big One), HONDA CB1300SUPERTouring, HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF
easy to grasp
[How is it used?
I got a VTR1000SP2 from an acquaintance that had been neglected for a long time, and the lever was not OEM, but a cheap type of machined type that looked a little weird when you held it.
I don't like it, it's on Short and I don't like the way it feels against my finger. If I liked it that way, the OEM lever would be that way, and motoGP has that on theirs. So I thought about going back to OEM, but since I usually play off-road, I chose ZETA.
I chose it because it is not a so-called dress-up shape.
Our VTR1000SP2 is not in the list of compatible models, but I checked the compatibility of other Manufacturer's products and bought it thinking it would be the same. I think it would be good to add compatibility, but since they are unpopular, they won't be added.
Was the one you received as per Image?
The quality of ZETA's sharpening has improved over the years. In the past, the anodized surface would fly off and peel in seconds, but now it is Large and durable.
How was your experience with it?
It is easy to grip and the adjustment mechanism is fine-tuned.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If you are a gutsy person who wants to use Remote adjuster, you can buy Flight lever on a top ranking.
View detail
Replacement of Protector for Armor HandguardSeries
Replaced the ZETA XC-PROProtector as it became warmer and the windproof effect was no longer needed.
While the ZETA XC-PROProtector was angular, the X3 Protector is rounded and well designed.
View detail
Fits: SUZUKI Across, SUZUKI Across, SUZUKI Across, SUZUKI Across, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI BANDIT400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400, SUZUKI GSX-R400
Lowest
The product was guaranteed to fit but could not be installed. View detail
Fits: YAMAHA CYGNUS Gryphus, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X-SR, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125SBasic, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125G, YAMAHA TMAX500, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA Axis Treat, YAMAHA N-MAX, YAMAHA N-MAX, YAMAHA MAXAM, YAMAHA MAJESTY250, YAMAHA JOG125, YAMAHA GRAND MAJESTY250, YAMAHA GRAND MAJESTY400, YAMAHA
Too hot.
It was installed on a VST 1050.
Installation is a relatively simple process that can be completed as long as the power supply from the car body is available. The thin seat shape makes the grip feel very comfortable.
I tried it on a March run at about 10 degrees Celsius and it warmed up quickly with Switch-on.
I thought it was warm, but soon it became as hot as if I was holding a hot can of coffee, and I turned off the Switch after about 5 minutes. After that, I would put it back on when my hands got cold.
It is probably at about 70 degrees, but I was concerned that this would damage the Grip's Rubber if used for long periods of time.
Also, the power consumption is about 30w, which is about the same as Headlight, so it may not be suitable for SmallEngine Displacement Volume, which is limited in the amount of power it can generate.
It would be appreciated if the temperature switch could be set to high, low, or off.
View detail
Simple and beautiful Forme!
I was looking for a simple and slimmer clutch lever, and I found this one.
I prefer a little more Short lever, but I like the feel.
It feels less thick and the excellent butchering makes it feel lighter.
View detail
I was satisfied with the 3cm but Large change
After purchasing the Motorcycle, the seating position was not quite right and I had back pain after running for a little while. View detail