Reviews
Sanctuary roller
This has a 10mm hole, one of the few rollers that has this measurement. Its well put together and you can regrease the bearings. Its quiet and is between a soft and hard material. Some vibration but will get better once its grooved. Its wide enough to incorporate a chain that may be off center where as a narrow roller may give you issues. Conclusion: this a well made roller and recommend. View detail
Was it good to purchase?
Attach S Size to KLX 125. In the OEM, the part of Rubber is scraped and the black stain is dirty - - -. After replacement it will not get dirty and it is in good condition. I was glad to exchange it.. View detail
Satisfied
I installed it because the lower side of Swingarm was cut at MONKEY LOWdown. I do not know the durability, but ... I think that it is safe because the lower side of Arm is not scraped by this. View detail
Is good.
I installed it in KLX 125. S Size is a little bigger than NORMAL, but you can attach it.
It is much better than NORMAL. It will be quiet..
View detail
Corocoro
NORMAL did not rotate, it got worn and replaced.
I think that resistance is also decreasing a little by rotating, but I do not feel it in particular.
Color (color) You can also choose, so the Dress - up effect is half the Large - - - ?
View detail
This should be attached from the beginning
The Mount BracketBolt that comes with GCraftRear Sets belongs to the picture below.
Because Chain interfered, I put up a Rubber board but it was useless. There is no reason to win Chain.
Looking at the Catalog of GCraft, it was that this part was used in case of interference.
My MONKEY seems Sprocket is a standard setting. I will interfere in that state.
I think that should it be OEM Parts Number from the beginning in that case. I think that it is a good thing as a part so I would like to give a star, but I lowered the evaluation from saying that OEM Parts Number will not go out.
Moreover, this price setting is nothing.
Just wearing this product probably will interfere with Swingarm.
I hope to improve even a little.
Anyway it is the main shaft that stops Rear Sets Body so it is not legal to shave off with Chain. Chain also hurts.
View detail
Just fit
Sher rattles are somewhat concerned. Okay ~ Rumor is one piece decrease phenomenon?
Try to remove it, Big! It was rotating pretty.
How to exchange.
Engineer Tsuduaku from day to day, may have been rotating as it attached Grease to the moving section. Individual difference?
First, Glasses on Reverse side (Prevents Nut from tampering as it is from the Reverse side) , The table is a long patterned Wrench (Torque up) , * STAND a cushioning material such as Dustcloth (Described later)
Because I could not insert it to the end at the Bolt, as soon as I got to Screw Mountain tighten together.
The impression is the Brush - Bo effect? ??Surely the sounds that Bearing is running are done. It is not bad.
If the color is Red or Blue, so dirt becomes more conspicuous, so change it to black color.
By the way, winding Dustcloth on Side Stand is because you can give power without hesitation. If you are not nervous, feel free.
View detail
Mounting on KLX 250
I installed it in KLX 250.
With OEM Roller and Black,
I thought that I wanted a color at some point and purchased it.
I can not see much if I install it - - - (;^^)
Because it is just replacing with OEM's Roller,
Installation is very easy.
View detail
Thanks for preparing OEM's Size
OEM Roller of WR250F has decayed, so exchanging, Bearing Smooth movements in internal organs. I'm glad that Color will also be One Point. Although I purchased M and L, it was slightly different. It was attached without problems. View detail
DRC Chain roller
Small Chain roller is also an exchange.
OEM is just stabbed in Rubber Color, but since DRC enters Bearing, it is obviously Upgrading, I think movement will improve a bit and I think that it will give you more or less muffling effect, OEM like plastic It was Chica Chi..
View detail
DRC Chain roller
Somewhat the diameter and width are different from OEM, but it will not be a problem
The contents are almost the same as the OEM, OEM was OK, but since the Rubber softens it will be effective.
View detail
Used for YZ250F
Since Roller on the lower side of YZ250F was decreasing, I chose L Size.
Bearing is also solid, rotation also Smooth.
It was cheaper than OEM Product.
View detail
Chain roller self-made
Along with extension of Rear suspension of XL 1200 C SPORTSTER 1200, I made Bracket and attached Chain Tensioner Roller to suppress slack at the lower side of Drive chain.
If there is nothing there is no problem, there is no problem, but if there is, the time lag of the slack of Chain which started running will decrease, the Throttle response will be felt well and the bash crash when throttle is closed will also decrease, so that it will be hard to make a shit is.
View detail
DRC Chain roller
Buy M Size Red for KLX 125.
KLX 125's OEM Roller does not rotate The inevitable Spec. So I exchanged with Chain at the same time.
After exchange it finally w
Since it is with Bearing, the movement is Smooth, Rubber makes it a pla, so it sounds a bit sharp, but it is an unnecessary Level.
I did not have any problems, but my friends seemed to need processing because the finish was bad, so I wonder if there is Rose Tsuki?
View detail
Replacement as OEM Product has deteriorated
XR250R (ME06) I exchanged ChainRoller bearing as it died. COSPA is also good and I think that I will purchase this product next time because I can choose Color & Roller size. There is no problem at all View detail
High Universal properties
Because it is a Motorcycle without Chen Roller, I bought it for my own work that prevents Swingarm's interference.
Actually, I used the same item once before, but I ran about 3000 kilometers and crushed it.
However, I feel that my way of installing was bad, rather than saying that the durability of this product is bad.
By saying that by both performance & Cost this product was purchased for the second time.
View detail
KLX125 is a little Large.
So I
NSK (NSK) Stainless Steel MINI Auteua BearingZZ Flange type Model SMF
Insert inside with SMF128ZZ
Use OEM by turning without Flange
Color of inner diameter 8 mm is required.
Washer etc. on the outside of Bearing as well
Devices are designed so that rotation becomes Smooth
Until 11 years the year is 14 / 8
However, since 12 years the outer diameter is 12.
Bolt size is 8 mm.
View detail
other than.
While making a remodeled Motorcycle of Monkey type, Chain is attached to the mounting parts of Rear Sets, and the part gets worn out by hitting it. At first I was Chain for Roller Monkey of GCraft Company, but the vibration was terrible! And moreover, it worn out considerably! It was not bad, but to search for others.
I bought Size of DRCChain roller, besides S Size Large Yeah! I attached the impression that I tried installing well because of Bearing! It is quiet in sound with Rubber! There is no vibration! Is it durable again?
View detail
Chain roller
2010 formula D - tiger 125 OEM Product was replaced because it was difficult to rotate further by 20,000 km at one side.
As a comment after replacement, I thought that it would rotate more freely, but there is some resistance.
When installing, we installed Washer of OEM Product in both SIDE of the product, but because the outer diameter is not matched, Roller side may be interfering with Washer.
I thought about adding and replacing Smaller Washer with outer diameter, but in this state, I used 500 kilometers, but Roller can be removed etc etc etc. Because it is not used as it is.
View detail
Because it has Bearing so Thrust no play, so quiet
Because OEM's are Rubber of Fixed Type, other company's rotary guide roller (Bear without Ring) Although it attached Thrust backlash, because the rattling sound became Large, I replaced it for this product. Large Kata rattling sound → It changes to small-sized loud noise, and is satisfied with Large. View detail