Reviews
Might be useful to have.
I think it depends on the way you fall, but in my case, when I fell standing up on a forest road, this helped me to minimize the Damage. View detail
Tightens up the look.
Was the one you received as per Image?
It was something I saw often, so it's on Image.
Was the installation difficult?
I used a hand guard from the same Manufacturer, so no problem at all!
How was your experience with it?
I don't know if it is useful yet because I haven't driven it in a place where it would be useful, but it looks very atmospheric and satisfies my sense of ownership.
[Included Parts:were they on?
Installation Bolt
[Was there anything that disappointed you?
None
Other items that would be helpful
Of course, the same Manufacturer's hand guard is only a few minutes' work!
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Impulse purchases that were not planned
What made you decide to buy?
I bought it elsewhere, half on impulse. (Lol)
[How is it used?
This is a change from PLOTbrembo Stainless SteelCaliper Mount Bolt.
[How was the installation?
Titanium has the Merit of being lighter than Steel. However, it is necessary to apply ThreadGrease to each bolt and tighten it. If you omit or forget to apply ThreadGrease, the screws will stick, resulting in a large risk of damage to the bolts.
[How was it when you used it?
The OEM CaliperMouthBolt is 62mm long and 44g, the PLOTbrembo Stainless SteelCaliper Mount Bolt is 70mm long and 55g, the Zita Titaniumium Caliper Mount Bolt is 70mm long and 26g, 18 PLOTMount BoltQuantity:The 2pcs were enough for one Zita Titaniumium Bolt, contributing to a slight weight reduction.
View detail
the handlebar is highlighted
Repurchase due to size miss It's perfect for giving points to the zeta handlebar. I recommend buying it because it's cheap. View detail
Fits: HONDA CRF250L, HONDA CRF250M, HONDA CRF250L(S), HONDA CRF300L
The thick Frame is useful!
Since it is a Small Shield, I wonder how effective the windshield is. However, in my opinion, the Level is better than no Level.
The advantage of the Large is that a Smartphone Holder, DriveRecorder, and Drink Holder can be attached to the thick and sturdy frame, making it possible to configure a cockpit on a motorcycle. Even with all of these things attached, there is no shaking at all.
It's really useful. 。 I'm glad I bought it 。 My Kok Pit is now complete.
View detail
Make it look good.
[How is it used?
Replaced with Titanium to avoid rust
I knew rust is bad for Parenthesis, so I don't like it.
Was the one you received as per Image?
I was a little bit smitten because it was lightweight for its appearance.
Was the installation difficult?
Easy to replace.
However, Torque is unknown.
The original Bolt said it felt like it was when it was removed.
It's about 40 N.m.
But the Manufacturer specified Torque of Titaniumium Bolt is about 24N.m.
Obviously, it's weak.
I was worried about leakage, so I tightened it at 30 N.m.
How was your experience with it?
No change felt.
But now that I've switched to Titanium, I feel good about it.
[Included Parts:were they on?
No. Anti-gouging agent should be applied.
[Was there anything that disappointed you?
Nothing in particular.
[Points to note]
I guess Torque management is the way to go.
I'd like to manage Torque and tighten it up properly and evenly etc. since it's an important part of the Brake.
You are wondering what tools to buy? We recommend Torque wrench from Tonichi!
https://www.webike.net/sd/20672766/
How did it compare to other products?
64Material:Titanium is a taper, so the surface is a little small.
Select made by Zita
I think the look is totally to my liking.
View detail
The Front is also Titanium to match the Rear.
[How is it used?
When the rear was replaced with brembo, the mount bolt was changed to Titanium to match the look.
Was the one you received as per Image?
The real one is cooler.
Was the installation difficult?
Easy as long as Torque management is in place.
Anti-gouging agent should be applied.
How was your experience with it?
Titanium weighs 23g compared to 42g for OEM, 76g lighter for 4pcs.
I don't really know the difference, but I like the sound of Titanium.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It would have been nice to have a VERSION without holes for Wiring.
Bolt with holes in it looks a bit Race ish.
I wanted to keep it a little more subdued.
[Points to note]
Aluminum and Titanium, so be careful of galling!
How did it compare to other products?
βMaterial:With Titaniumium's Bolt, four bottles cost almost 30,000 yen.
A Titaniumium Bolt from Zita would cost about $2500 per pc.
It costs only 10,000 yen to replace four bottles.
I am afraid to use unknown Titaniumium Bolt sold on Amazon or Yahoo!
View detail
Cool with increased protection
ZETAArmor HandguardBent on CRF150L.
The instruction manual is also very helpful and reliable. Basic installation is also easy.
If there was a hole on the SIDE of the handlebar rubber, we would have installed it as is, but since our car was blocked by the rubber, we drilled a hole with a cutter (the Instruction Manual also says to replace the grips).
The Left Side was easily installed, but on the Right SideThrottle side, the bottom of the Rubber was blocked by Plastic.
Carefully crush this with a Hammer, etc. and install. CRF150L users, please be careful.
Once the hole is made, installation is easy and from there it takes about 10 minutes, as shown in the photo.
It looks good and has a large increase in protection.
It is good enough as it is, but we will also add XCProtector after this.
View detail
Easy to install, cost-effective, good-looking
This XCProtector is installed on a CRF150L with ZETAArmor HandguardBent.
The time required is about 2 to 3 minutes since it only stops two Screws on each One Side.
It looks LARGE and better as shown in the photo.
Cost-effective and great.
View detail
It's crisp and clean.
This is a change from OEM.
The installation can be done without too much difficulty if you have experience in such work as replacing the clutch lever, since there is a translation (please enter hereManual).
Also, while installing it, I felt that the accuracy of the cutting process may vary a bit, and you may be dissatisfied with the Quick Adjuster for Red and Blue. The color will deteriorate under ultraviolet light while in use, and the color will fade, but if you are considering purchasing these as Custom, please be aware of this.
Grease is also applied to the bolt that fixes the lever from the beginning, and the handlebar is fixed with a clamp system, and the screw is very precise, so it was installed comfortably.
The clamp that fixes the handlebar is a little hard plastic material, so there is a possibility that the entire clamp may rotate when it falls over. If you are concerned about it, you may want to change to RubberMaterial.
As for the feel of the operation, as per the Title, it is snappy and sharp.
If you want a direct feel from it, I think you can further modify the Sleeve in the Thailandico fixation area.
Even with the Sleeve position in its normal state, the OEMLever comparison is better, so I felt that the Point is a point of preference depending on how a person uses Clutch.
I wish I had not been stingy and purchased it earlier, as it is one of the other Items that can be fine-tuned for Lever position.
View detail
Used for RADIPON MASTER
I purchased this product to install a Guard made by another company.
The handlebar is very well made, and the handlebar is fixed with 4 screws, so even if it loosens a little, it is not likely to become defective immediately.
This time I installed it on a Fat bar and was able to install it without any problems.
I put it on as it says RightLeft on the product, but there seemed to be no difference in the shape.
I would like to see if it is sturdy enough, since I think this kind of thing plays a stronger role in resisting impact by rotating rather than guarding against falls.
View detail
To avoid breaking the Lever
I installed it to enjoy Motorcycle in various Situations in the future.
Installation, etc., is not a problem at all, as it is often seen in videos, etc.
However, if you need to open the throttle cone and want to process it nicely, you need to have tools.
I think it is easy to work with.
After installation, the motorcycle looks tighter and I am satisfied.
I don't want to feel the effects as much as possible, but it has become a talisman.
View detail
Expensive but good product.
I bought it for a place where I really want to fix Wiring.
It's Titanium, so it's expensive, but I'm satisfied.
View detail
Good to have a variety of colors to choose from.
This one is good because it offers a variety of Coloring choices.
Both Cx and sx bars come with Pad as standard, but the Black is Quantity related to the color of the bar.:Set
Inevitably, every time you buy a bar, Black's Bar pad will accumulate in droves! 。
There is almost no profit to be made selling them on Mercari or Yahoo!
I would like to be able to choose the color of the Pad anyway, but I think it would be better if the Pad is treated as an Option like the comp bar and the unit cost of the Handlebar is lowered.
View detail
Fits: KAWASAKI D-TRACKER, KAWASAKI KLX250, Others , YAMAHA WR250R, YAMAHA WR250X
There are some good things that only a comp bar can do.
I put a MOTARDMedium comp bar on my CRF250RLY50.
I had worn cx bar mx-123Blue before, but I thought it would be more comfortable with a little more aperture in terms of position. I decided that the comp bar would fit CRF250RLY50, which is not so strong and rigid, and bought it.
As a result Large was the right answer
The position, moderate rigidity of the handlebar, and coloring are perfect.
View detail
as necessary
This is the purchase of consumables that are included with the exclusive product.
There is also a Dirt run, and I was a little concerned about the Chain coming off, so I bought it.
View detail
For dress-up purposes.
[How is it used? Touring Sometimes I want to go into the mountains.
Was the one you received as per Image? Yes, it is neither large nor small.
Was the installation difficult? Very easy.
How was your experience with it? It's spring and the weather is nice, so I don't feel the effect of windproofing etc., but it looks better! 。
[Included Parts:were they on? Mounting Bolt
[Was there anything that disappointed you? There is none
Other items that would be helpful
Since the Armour Hand Guard Bend was originally installed first, it naturally fits perfectly.
We will go into the mountains and see if this works.
View detail
Stability only possible with Fat bar
This is a Review at least 6 months after purchase.
Quantity:Pair (for Left and Right) Fell multiple times on Tarmac in (SlipDown type) were, but there are no visible signs of breakage or bending, and the feel of the product remains the same.
The length of the bar is 800mm, which may be a little too large for some Japanese, perhaps due in part to the length adapted to the physique of Westerners. I use it with the bar packed.
Motocross athletes often use them without filling them these days, so if you take that into account, you can use them without any particular concerns.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI KLX125, KAWASAKI KLX150S, Others
Used for DT50.
I'm 184cm tall and the OEMHandlebar was making me feel like Curve was repricing, so I changed it.
Operability has been improved.
View detail