Reviews
Ai-Net Euro front blinker & rear tail unit
Thank you Ai-Net for your euro blinker & rear tail unit. Very nice quality. Clear lens and lights. Matches the mica candy apple red color of my Fusion CN250. Transaction was very good also as with the packaging. Arrived here in the Philippines at expected time. View detail
![[AEBS] LED Blinker Lamp Set](https://img.webike-cdn.net/catalogue/images/29483/61028_01_TS.jpg)
A◯TIVELicense Plate Holder with LED Blinker like this
Installed on a GSX-R1000R 2019
Title
I found it on Amaz◯n, but I didn't expect webike to carry it too.
Unlike the expensive original, it can be made to look similar at a relatively low cost.
Also, if the original Blinker is broken, this may be a good replacement.
(I didn't compare them, so I'm not sure if the Wiring removal and mounting screw positions match.)
The light intensity is sufficient and is visible in daylight.
However, is the directionality strong? If you install the Number in a way that makes it hard to see from the following car.
Wiring is the same as general LED Blinker.
The line is very thin, so you need to be careful not to cut it.
R1000 below (L9) For installation on the
The R1000R is originally an LED Blinker, but if you pimp it, it may become a High flasher.
In fact, when I popped it on, there was no problem while the engine was stopped, but after the engine started, it became a high flasher when the voltage exceeded 14V.
For this reason, it is necessary to put a resistor in the power consumption adjustment.
By the way, my vehicle worked fine if I connected a 30 Ohm resistor.
(Also, the original seems to be a high flasher as well, but the resistor to add is different.)
For your information.
View detail
Wiring at both ends is thick
[How is it used?
It is used as a safety protection for the 12V Wiring handling from Battery.
How was your experience with it?
The cable of both ends of the holder is thicker because the Fuse of up to 30A can be attached to this product. I think that there is no problem if it is a place where it is not seen though the feeling of discomfort comes out when I do Holder attachment etc. with a thin sq wire.
[Points to note]
Fuse is not included and you will need to purchase your own MINI flat type.
For use outside the car, we use the Wiring Cover together to increase the waterproof property.
View detail
![A-Screw] LED Blinker Tail Lamp Set](https://global.webike-cdn.net/photo/impression/68/68cec7752c89409c7d5021afb823ed20L.jpg)
Along with the rear fender-less
There is also a smaller LED Blinker, but I thought about the appeal to the following vehicle, and I installed this one which can be refreshed next to the License Plate at a lower price than ACTIVE products while gaining the area of the light emitting part, with the Bracket of Home center (Reflector I installed it with Bracket (Reflector is ACTIVE TYPE 3) and Screws.
Blinker relay is replaced to convert to LED, License Plate Light is still OEM.
View detail
Tough impression of Bates Headlight
I was looking for a Bates Headlight with Light Guard with a tough vibe to customize it to a military look and came across this one.
Black Body and Yellow Lens.
The material is Steel and it is painted Black. The attached Nut and Washer are also BlackPlated.
If you use it for a long time, there is a possibility that Rust will float.
The paint is careful and there is no Wound.
Wiring is Minus, Low and High with Bullet Terminal's Male on each.
It's not a Coupler, but it's not too difficult if you attach the Bullet TerminalFemale to the corresponding cord on the body side.
However, the Net description and the code colors for low and high were reversed.
As for the performance as the important light, the irradiation range is a little narrow and dark impression, but because it is yellow color, it is the range which can be satisfied as a sub-Motorcycle use because the shade comes to the surface.
View detail
Fits: HONDA fusion, HONDA fusion, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION
Good product
Very good. It takes one week from order to receipt. The packaging of the accessories is also very safe. The most important thing is that the quality of the accessories is very good. They are basically the same as the original ones. They have not been replaced yet, etc. When the N many accessories arrive together, do it again. Will continue to place orders, if there is a discount on freight, it would be even more ideal. ---------------------------------------------- Very good, from order to receipt of goods a week, faster, accessories, packaging is also very safe, the most important thing is good quality accessories, original pieces with essentially the same, there is no replacement up, other more than N before you start fitting together almost to the time. It will continue under orders, if the freight can be a discount, even more ideal. Powered by Google Translator View detail
Fits: HONDA CB-1, HONDA VTR250, HONDA jade, HONDA HORNET900, HONDA HORNET600, HONDA HORNET250, HONDA CB400SF, HONDA CB1300 SF, HONDA CB400SF, HONDA CB1000 SF (Big One)
I'm glad I bought it
The Blinker Bracket on my 19991 JADE broke off and blew up.
I bought it at the last minute.
The standard of the Cable is different, and it is only OuterCase that I used.
Cable and Valve both used the old one, but it didn't feel any different.
For the price, this was a super bargain for the quality.
View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
CB125T JC06
I bought it for the spare of CB125T JC06. It was darker than NORMAL and the optical axis was not clear. Well, it is the feeling that it cannot be helped for the price. When I tried to install it again, the high beam did not light up. Unfortunately, I discarded it. I think it is good to have it for spare because the price is cheap. View detail
Fits: HONDA CB750, HONDA CBX250, HONDA NS250, HONDA NS400, HONDA VF400, HONDA Forza(MF10), HONDA fusion, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, SUZUKI DF200, SUZUKI GSX400, SUZUKI RF400, SUZUKI RG400, YAMAHA XZ400, YAMAHA vino, SUZUKI SV1000S, SUZUKI SV1000, KAWASAKI ZZR1200, KAWASAKI ZX-12R, KAWASAKI 1400GTR
Satisfactory product
Used by Z125PRO
I bought it as a stopgap measure because the Light of OEM was out
There is no difference between OEM and Large so far in terms of usage
I thought about the LED, but the Gold amount is also inexpensive, so I'll use it as is
View detail
Fits: HONDA CB-1, HONDA VTR250, HONDA jade, HONDA HORNET900, HONDA HORNET600, HONDA HORNET250, HONDA CB400SF, HONDA CB1300 SF, HONDA CB400SF, HONDA CB1000 SF (Big One)
You'll be happy with the low price, and it won't hurt!
I checked the texture and strength when it arrived, and I'm satisfied with the price, strength and texture! First of all, the price, Quantity:Pair (for Left and Right) And it's cheap at about $1,000! There is a rubber shock absorber in the body side of the car I'll let it go The texture of the exterior has a BALI, but it comes off easily, so no problem, the internals are crude! Lots of BALI, but it's not visible, so you can remove it with a Cutter Knife and you're good to go Yes, sir! View detail
Fits: YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200, YAMAHA SRX400, YAMAHA FZR400, YAMAHA FZR250
It's just taking shape
If you're going to buy one, be prepared to process it If you think you can pimp it out, you're wrong
First of all, the Large size of the Wiring Evo-Si is different from the OEM product The inner bracket is different from that of the OEM product, so the bulb is different If it is not, it will not relay
In the end, I used only the Body and machined and installed the OEM internal Bracket
Lens also came off easily just by removing the Screw There is no doubt that water can easily get into it I used a liquid Gasket to deal with this
View detail
Fits: HONDA fusion, HONDA fusion, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION
Good service
Very compliment for accurate consignement and packaging five star I recive today in Italy all good good good good good good good good View detail
Arrived
All perfect order arrived on schedule all as described exceptional thank you I'll be back to make purchases from you good day sale emiliano All perfect order arrived on schedule all as described exceptional thank you I will come back to make purchases from you good day sale emiliano translated by Google Translator View detail
Fits: Others for 12V * Attached bracket can be removed for use
It was defective
I purchased this product because the Horn bracket I was using was broken It did not sound at all when I did wiring I diverted only the Bracket because it was too much trouble to return it by a cheap product View detail
I could not use it at all
Purchase expecting from COSPA. Although the apparent appearance was good, the accuracy of the shape was bad, and if it could be used if processed it was not Yu substitute. I thought it was just Valve but it was not possible to wake up High flasher. View detail
Fits: HARLEY-DAVIDSON FXLR DYNA LOWRIDER, HARLEY-DAVIDSON FXSTC SOFTAIL CUSTOM, HARLEY-DAVIDSON XL1200, HARLEY-DAVIDSON SPORTSTER FORTYEIGHT, HONDA VT1100, HONDA VT1100, HONDA valkyrie, HONDA valkyrie, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, KAWASAKI Eliminator 400, KAWASAKI Eliminator 750, HARLEY-DAVIDSON 883, HONDA Shadow Custom, HONDA shadow, HONDA shadow slasher, SUZUKI Desperado X, YAMAHA DS, YAMAHA DSC, YAMAHA Virago XV920
Cost performance was not good.
shape - Waterproof measures were satisfactory. In the Valve with attached ... There was a description of the item saying, but the attached Valve did not blink from the beginning. After switching to Valve of Tan Rei, it flashed normally. The resistance value was totally different even at the same 10 W. I wanted this price to be a decent Valve. Even cheaper items, I had a proper Valve. Valve was not available at all. Valve purchase fee has become extra expense. View detail
AI-NET Multi Reflector Headlight
Very good price quality value. Increases the light beam apear to the old used one. Needed some drilling for the bolt holes that it fits well. The light will increase the safety and looks for the FUSION. View detail
Fits: HONDA fusion, HONDA fusion, HONDA FUSION, HONDA FUSION, HONDA FUSION, HONDA FUSION
AI-NET OEM Type Speedometer Cover
Ai-Net OEM Type Speedometer Cover was has very good price quality value. Only difference for the original is that there is no HONDA CN250 texts. Very easy to assembly. Especially i liked the detail that there is no honda and CN250 lights. View detail
Can't expect much for this price
The design of the blinkers and tail unit is nice, and really modernises the Helix, and gives it a sporty custom look, however the build quality and quality of the plastic is the cheapest kind, which should be quite obvious at this price level. You should be extremely careful when changing light bulbs to the tail unit, because the transparent plastic pieces don't entirely fit, and using force will snap the cheap plastic. View detail
Fits: HONDA gyro canopy, YAMAHA TMAX500, YAMAHA TW225E, YAMAHA JOG (2Cycle), YAMAHA XG250 TRICKER, Others , YAMAHA MAJESTY125, YAMAHA MAJESTY125, YAMAHA JOG, YAMAHA CYGNUS X, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI RV200 VANVAN, SUZUKI 250SB, KAWASAKI ESTRELLA, KAWASAKI KLX250ES, KAWASAKI KLX250, KAWASAKI D Tracker, KAWASAKI 250TR, HONDA MONKEY
How many turns are you waiting for? Purchase
First I opened the box and Big Li.
There was a Meter in the bag of PetitPetit and the outside wrapped in Cushion wood and it was in a step Ball.
Are not you?
The manual is ...
It is not included. (^_^;)
Because it is the price, is this something like that!
I tought.
I think GORILLA will replace it with the Super street outer rotor kit for Mukawa 6 vCHALY from Point and I think that it will be helpful.
There are five Wiring.
Black I'm stuck Back light Minus
Minus with Green Bullet Terminal
Red Stripped Back light Plus
Plus with Black Bullet Terminal
BlackYellow Bullet Terminal Pulse Signal Plus
It worked on. I can not take care of it because it is troublesome,
Minus of Back light and Minus of Main
Back light Plus and Main Plus
I connected them directly and connected them directly from Battery. When I do not ride I do not care because I remove the Battery terminal.
Impression attached
Large It is impressive?. Tachometer's movement is slow relative to Engine speed!
It is the impression that. As Idling points at 2,500 revolutions, I thought it was eh, but I think that it is better than nothing.
Back light is beautiful!
I am dazzling a fluffy LED
Since I wanted to attach it to Handlebar, I bought another company Clamp later.
View detail