Reviews
Fits: HONDA CBR250R [MC41]., HONDA 400X [NC47]., HONDA CB250F(14-15), HONDA CB250F(14-15)
Divert to other cars
The car model is different, but I tried to put it on for a change after considering the shape and other factors.
As a result, I managed to get it on.
However, there is one screw hole that does not fit, so it is fixed at 2 points instead of 3 bolts.
Because of Bag Support, I think that Large is sturdy because I think that the load does not apply directly to Large.
It's firmly in place.
The downside is that the price is too high.
View detail
Installed on ZZr1100D
Under Cowl needs to be machined. Mounting points are required for Quantity:Pair (for Left and Right) I made the Guard by myself. Please refer to the picture. The shape is beautiful. View detail
Installation of Camera on Chinese Draco
This is not the one I wanted. However, the Drorekos I purchased had a longer rear than the screw tightening position. As a result, we decided to choose it from another manufacturer's products.
The target products are this and POSH. The POSH one requires a cheap bracket to be attached to the Drorecco, and this one can be attached with a solid sub-Bracket, which is the deciding factor.
And Quantity:Pair (for Left and Right) It's a Limit while adjusting the video to a Limit, but I avoided the Blinker and completed the installation (but it's impossible with STD Blinker). The video was taken without blurring.
It is important to note that the upper part of the License Plate Base is pinched and cannot be bolted unless it is the same size as the Plate. So I changed to KIJIMA's at the same time with this plate.
By the way, I'm wondering why you don't use Black for the attached Porto. In the picture below, it is prepared separately.
View detail
I wanted a Mistuba Sankova Draco Bracket.
I was looking for a RearCamera Bracket from Drorecamera and found this one at a motorcycle supply store.
I was not sure if my motorcycle was a Fender Eliminator, but I managed to get it on.
Probably easy to put on if it's not a Fender Eliminator.
The thing itself is pretty solid, so as long as the Nut and Screw in the mounting area don't loosen due to vibration, I don't think durability will be an issue.
View detail
Aiming to increase the cooling effect.
This is an exchange from the OEM 1.1kg. As for the product in question, because 1.3kg and the Compression value only went up slightly, it was the effect of the feeling degree as for the experience. It may be more effective in terms of raising the cooling effect to replace it with Coolant which cools more than that.
The other thing I was surprisingly happy about was that it was easier to turn it around than the OEM.
View detail
This makes it so much easier!
When pushing Piston back, I used to insert the Driver between the Pads and expand it, but I did not want to scratch the Pads, so I bought a special tool to open this Piston. So I bought a special tool to open the Piston. It is very easy to use and I am satisfied with it. View detail
It fits the Small Type Number with no problem.
We've been in a rear-end collision before on a Motorcycle. "Apparently,
He was thrown into the ICU for brain attendance, and although he came back, he regained consciousness four days later, and it wasn't until a week had passed that his short-term memory was volatile and not written into his long-term memory, and he didn't remember anything from a day ago.
I don't have any memory of the accident, and reluctantly, I was judged to be in a 0:100 rear-end collision with a crazy JJY, and I didn't have enough material to overturn it, so I've been using DriveRecorder since then, except for purely off cars.
I'm a paranoid, so ω
Of course, I installed the Drive Recorder on JA55 CT125CT110 HUNTER CUB as well, but the Endurance model on Ural Sidecar was not so reliable due to the moisture condensation in Monitor. I installed a Drive Recorder with Camera's Monitor
The only problem is the lack of waterproofing on the Monitor;
Then, Order this Camera Bracket to Mount
It's a very special product and has a wide adjustment range with two SmallScrews to hold the Camera.
This is definitely a better option than the stingy and teketotal Bracket
There's no point in using Recorder if it's not useful in a pinch;
Since then, there have been no accidents on Motorcycles other than single-vehicle collisions, and I've been hit by a car 4 times;
For goodness sake, it's BoyScout, but it's a heavy word
View detail
High rigidity and no video blur.
I bought it to change the position of the Drorecord for the installation of the Fender Eliminator Kit.
This is for use with the Mistuba Sankova EDR-21G.
No problems with the rigidity, and it won't move when tightened up.
However, it is better not to lose the Spacer that comes with the Drorecco because it cannot be fixed firmly unless you tighten the Bolt between them.
I was thinking of using it with the Tanax Plate Hook 3, but I gave up because it interfered with it and was impossible to install it.
View detail
Used in the MT-09 RearMountCamera
As the Title says, I bought it to equip my 2017 MT-09 with a front and rear draco
It is Exactly for the Mistuba Sankova EDR-21G
This product is not only a Mistuba Sankhowa
"Mistuba Sankova EDR -11/21/21G and KIJIMA AD720/1080 J. Astro Scauper - Just Fit Design for Pio/Torus It is clearly stated that
There is no need to use the double-sided tape that comes with the Camera You can mount to the Screw hole
Quantity:Pair (for Left and Right) You can also adjust the number to some extent, so you can use the buffer between the upper part of the number and the cowl (or tail lamp) It is designed to avoid a wide range of car models … probably most car models It can be attached
With Steel and BlackPainting, you won't have to worry about strength
I think it's hard to find a place to put the Fender Eliminator-ized MODEL So it's essential in such cases
If you use double-sided tape, it will move freely, but you can use it to fix the bolts It will be
It doesn't move, and I expect the video itself to be resistant to blur (vibration)
View detail
You can't tighten it up!
I've been asking the motorcycle shop to replace the Filter, but the new It was decided to increase the number of motorcycles, and indeed, three motorcycles were replaced with oil The cost of changing the oil to a motorcycle shop every time I go to a motorcycle shop would be too much, so I decided to do it myself
I've done the oil exchange itself a few times in the past, but the oil filter wrench Since I didn't have a motorcycle, I decided to buy one I was thinking about getting a full set of Wrenches when I heard about this product
The deciding factor in the purchase
9.Loosen and tighten the Filter of any size with the 5mm Wrench I can do that! And since it comes with a 12.7mm Socket, you can use your own Torque wrench to I can manage Torque! I was so impressed with the product that I bought it right away (I can't tighten it up, as I'll discuss below.)
It's amazing what a structure you can loosen and tighten then! I thought that was not the case
My Thoughts on Actual Use
First of all, as far as loosening it, it's a little slippery, but it's not a problem You can certainly loosen the multi-Size Filter, so it's insanely convenient! That was my impression
The problem is the tightening It cannot be tightened The internal structure is simply gears, and when you turn it with Wrench, the Zipper gears turn and you can check But of course if you turn it to the opposite direction, it will only open It is not possible to tighten it when I confirmed it in other sites for trial I checked at another site and found that it cannot be tightened Seriously, I thought, I was troubled whether to return it or not, but I have tried to use the Filter of various sizes I can loosen it, so, well, that's fine... In the end, I'm going to have to tighten it by hand...
What I'd like to see improved
The product itself is good, and I would dare to say that the length and the grip of the Zipper is a little more I wanted the Rubber part to be more creative The other thing is the product description, but it can't be tightened, so you should write it down a bit more I thought
Products compared
I compared it to the Filter wrench per KTC, DAYTONA and Emon
[Others]
The packaging came in a thick, solid Vinyl bag, as shown in the pictures
View detail
I wouldn't recommend it
Since the Zipper only works in the direction of loosening, it expands when it is tightened, the Cup-style Filter wrench is much easier to use
Also, the Zipper slipped when I loosened it and I had to remove it while holding it down by hand
View detail
enough
This kind of material is indispensable for parking in unpaved area I carry it in my Tank Bag when I go for a long ride LargeIt's not too tight, but it's strong enough
We have not yet been able to evaluate the durability of this product over time because it has only been used for a few months If I do, I'll post again then
View detail
Precious 1.3kgf/cm2 Cap
[Was there anything that disappointed you?
None at all The look and feel of the design is very fresh and un-Radiator Cap-like
It was able to cap the installation without any rattling
The water temperature does not rise too high and the pressure is higher than that of the OEM
The water temperature is less likely to rise
Do you have any wishes or improvements you would like to make for the Manufacturer?
It's a consumable product, and it's a youthful full one that doesn't have an extreme pressure value or extreme
I would like the price to be a little more Reasonable
[Do you have any products to compare it to?
I compared it to the RadiatorCap made by DAYTONA and DRC
The same pressure value as the OEM Product (1.1kgf/cm2) or extremely high values (1.6 to 1kgf/cm2) etc2.1.6 to 1kgf/cm2), or extremely high (1.6 to 1kgf/cm2), etc.
I couldn't find one with the value I wanted, so I used the only 1.3kgf/cm2 that Webike offers Japanese painting
It was the product in question
Incidentally, in the past "infinite" I found a RadiatorCap of 1.3kgf/cm2 at Brand
I really wanted that, but unfortunately it's discontinued
Frequently Asked Items
What made you decide to buy?
The fact that the pressure 1.3 kgf/cm2 was what I wanted most
I wasn't sure if it would fit, but I was looking it up on the Internet
I was relieved to find someone who had installed it on the same type of car, so I bought it
How was your experience with it?
There was no rattling at all during the installation process
Also, although the Cap shape is different from the normal one, it did not interfere anywhere
In fact, it is more Compact than the usual Cap shape, so there is no need to worry about that
As for the key cooling performance, the Cap of the OEM is 1.1kgf/cm2
1.With 3kgf/cm2, the cooling performance has been improved to a degree
Even with the recent abnormal summer temperatures, the rise in water temperature has been pleasantly gradual
I think this is about right, because any more pressure might cause damage to the cooling lines In fact, I'm using it, but so far I haven't had any problems
Was the installation difficult?
Since the cap shape is easy to grasp, the
There was also a Merit that didn't make my fingers hurt during the replacement process
【Please tell me the installation point and hang】
From the shape of the cap, it may be difficult to see where the claws are located
Make sure you are well positioned and framed
It is easier to close the Cap than the normal shape once it is set up
[Was the Instruction Manual easy to understand?
There was no Instruction Manual available
(It's not really something that needs explaining...)
[Included Parts:were they on?
None
[Others]
1.The value of 3kgf/cm2 is suitable for sports riding, but it is also a good value for
The logo "type-R" is displayed confidently on the screen with
It's quite a grin (You can't usually see it.)
I was able to use the CBR1000RR 2007 (late SC57) with no problems
If you are looking for a 1.3kgf/cm2 Cap
I highly recommend it
However, the price is higher than the average Radiator Cap, but the Neck
Other than that, I have no complaints at all
View detail
Good material
so fast shipping. the iterms are exactly the picture. Good material. The box look so classic with dark red. Perfect service. View detail
Diversion as MultiBracket
We still need to get a handle on the rainy weather, but one smartphone app that I wanted to use the NavigationREMOTE CONTROLLER and easy to remove and I was looking for something that could be installed, and when I heard about this product, I decided to purchase it
It's possible to use the Magicron Spec. without modification, but I'm not sure if it's possible to change the batteries or not They're sold at the home center to create more effective joints to prevent them from falling due to vibration AluminumAngle is used to fix the style to this product I took it
The Mirror bracket on the Lever is also used to attach to the Bracket By fixing it, the REMOTE CONTROLLER can be used with one hand became
Basically, it's used for stopping at intersections, but unlike the gloves, it's not used for pushing It's a great way to relieve the frustration caused by
View detail
Stylish
The Mirror co-tightening bracket that was put on without permission at a Motorcycle supply store is lame I replaced it with this one because it became difficult to do maintenance on Lever
I can place Antennas where they won't get in the way and they look nice and uncomfortable
View detail
Fits: HONDA CBR250R [MC41]., HONDA 400X [NC47]., HONDA CB250F(14-15), HONDA CB250F(14-15)
Note on Compatible Car Models
The CBR250R and CBR650F's Rear Footpegs were similar in shape, so they were probably attached I bought it because I thought I would be able to
However, although there is a screw stop between the footpeg and the frame, the Heel I couldn't install it properly because the size of the Guard didn't fit at all
View detail
It will look better
It's a Radiator cap that hasn't been replaced in over 20 years and it looks better than the OEM It was good, so I bought it The shape is circular, so it takes a little more force to turn it than the OEM View detail
Good??
I think that anyone can exchange it.
It's clean because Bolt is fixed on Main plate.
Because all OEM Parts can be used, other than Kit is not necessary.
View detail
It is quick to break
There was a time when Position ceased to light up in 3 months after installation.
Blinker's output was gone in 1 year and 4 months after installation. I used it for a while
It never cured. Mileage is around 7,000 km.
It seems that the number of Watt of output is also within the appropriate range, different from consumables like Tire and Oil, so this is a defect as a product.
View detail