Reviews
Fits: BMW F800GS, BMW F650GS Twin, BMW F700GS
When attaching, the attached Spacer was used, but die length was not able to attach short about 7 mm. Be careful.
When attaching, the attached Spacer was used, but die length was not able to attach short about 7 mm.
Be careful.
View detail
Fits: TRIUMPH STREET TRIPLE, TRIUMPH STREET TRIPLE, TRIUMPH TIGER
[Webike Monitor] Cling in order to use GIVI T489 Tank lock. Although there are few vehicle types which appear in the correspondence vehicle type List of Easy-Lock BF02 at the DAYTONA of the domestic agent, if it searches at the Site of
[Webike Monitor] Cling in order to use
GIVI T489 Tank lock.
Although there are few vehicle types which appear in the correspondence vehicle type List of Easy-Lock BF02 at the DAYTONA of the
domestic agent, if it searches at the Site of the GIVI head family, SHIVER 750 GT of its own car is also on correspondence vehicle type strike.
Any problem cannot be found as a photograph and it attached.
Although it is only a vehicle type of a Triumph, being written to the
Manual is satisfactory if the die length of the screw thread removed from the Tank cap is checked and attached.
In the case of
SHIVER 750 GT, it used it each two merits and demerits at a time alternately.
View detail
Fits: HARLEY-DAVIDSON XLH883, HARLEY-DAVIDSON XLH1000 SPORTSTER 1000, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SOFTAILFamily
I think that a car body may be matched since it is a Black.When attached together with the Support, the die length of the Bolt was lacking.
I think that a car body may be matched since it is a Black.When attached together with the
Support, the die length of the Bolt was lacking.
View detail
Fits: TRIUMPH BONNEVILLE [Bonneville]., TRIUMPH BONNEVILLE [Bonneville].
[Webike Monitor] It is the completion of wearing only at 共締め(ing) with two Screws, the Suspension and a Rear step. Since it is almost comfortable even if texture is also good and the Side bag is not attached, it begins to keep attaching. Since only
[Webike Monitor] It is the completion of wearing only at 共締め(ing) with two Screws, the
Suspension and a Rear step.
Since it is almost comfortable even if texture is also good and the Side bag is not attached, it begins to keep attaching.
Since only left-hand side is treated by Webike, let's look for right-hand side by others.
View detail
![Side Bag Support [TE1111]](https://global.webike-cdn.net/photo/article/12/1344670428612L.jpg)
Fits: HONDA NC700S, HONDA NC700X, HONDA NC750X, HONDA NC750X, HONDA NC750S, HONDA NC750S
It equips simultaneously with the Fitting for GIVI Top cases. Since it was only for the vehicle type, when saying that it was natural, it was natural, but there are no Gaps, such as a screw hole, and it has equipped exactly. The Frame is contained also
It equips simultaneously with the Fitting for GIVI Top cases. Since it was only for the vehicle type, when saying that it was natural, it was natural, but there are no Gaps, such as a screw hole, and it has equipped exactly. The Frame is contained also in the Tandem-step and Number-plate side, and it seems to be strong. Although iron was only bent, he may think that it is high, but I think that there is worth of a price. View detail
It was an Exactly although attachment was also easy although attached to the VULCAN DRIFTER, and it was an object for Yamahas SR400.
It was an Exactly although attachment was also easy although attached to the VULCAN DRIFTER, and it was an object for Yamahas SR400. View detail
It purchases in order to attach a Saddle bag. It has equipped easily especially, without being difficult. Structure was also solid, and a Back can be attached now in comfort.
It purchases in order to attach a Saddle bag.
It has equipped easily especially, without being difficult.
Structure was also solid, and a Back can be attached now in comfort.
View detail
Back support was purchased in order to attach the saddle back of Degner to Eliminator 250V. Although the image photographs at the time of purchase are the vehicles to which sissy bar is not attached, genuine OP sissy bar is attached to my motorbike. Eve
Back support was purchased in order to attach the saddle back of Degner to Eliminator 250V. Although the image photographs at the time of purchase are the vehicles to which sissy bar is not attached, genuine OP sissy bar is attached to my motorbike. Even if I saw the maker HP, wherever I see, a sissy bar attachment was not described. Although I thoughtt it was OK, when the saddle back was arrived and I opened, there was no attachment explanation of sissy bar. Even if I unite with the vehicle, it is not likely to be attached somehow. The position which hits the 23-mm spacer at the root of back support may be also in a sissy bar and I struggled to attach. It was "not having assumed the attachment to sissy bar vehicles", when I asked the maker. There was no assumption even if it is for genuine. The maker supporsed that it stopped from the outside of sissy bar with the long bolt, but the stop position of back support is not parallel approximately, and since it is offset, it cannot stop firmly on the side plate of sissy bar. I regard that of a manufacture system as it being a problem to it, and it also seems to be difficult for an OFF theory and quantity to be too different by right and left, and to compensate using color. Since it reaches outside even if it is able to equip, the gap between the saddle back becomes not parallel. Since the maker's person in charge was a very kind, I tell about the present condition again and would like to look for solution. Conclusion: Even if it is specification product, attachment to genuine sissy bar vehicles is improper, I think. View detail
a front side -- the fixed Nut of a Rear suspension -- a Tandem bar -- since the Plate to fix has thickness considerably although a bundle is carried out, if it does not take care, does a Nut separate? a Screw lock is applied -- as -- although written ...
a front side -- the fixed Nut of a Rear suspension -- a Tandem bar -- since the Plate to fix has thickness considerably although a bundle is carried out, if it does not take care, does a Nut separate? a Screw lock is applied -- as -- although written ... View detail
It purchased simultaneously with the object for right-hand side. Since it is goods which are not symmetrical, there is no compatibility the object for right-hand side and for left-hand side. When carrying out a Tandem, if a fellow passenger's
It purchased simultaneously with the object for right-hand side.
Since it is goods which are not symmetrical, there is no compatibility the object for right-hand side and for left-hand side.
When carrying out a Tandem, if a fellow passenger's calf hits this Saddlebag support was worried, but it does not hit in the usual riding posture.
:
which is quotation from the Impression for left-hand side in below
it equipped for interference with the Rear suspension at the time of using a Side bag, and the involvement prevention to a Tire.
It is a Beauty, and a Plating does not spoil the whole appearance Balance in the state without a Side bag, either, but is good touch.
Where a Center stand is stood about single-sided 15 minute, it equipped with
working hours.
When letting the Bolt of a Rear-suspension portion pass, the hole with a Frame shifted, and a Bolt did not pass, but it got impatient, but it succeeded by letting a Bolt pass, raising a car body.
Although used together with
and a Rear carrier, die length was not necessarily insufficient with an especially satisfactory pure Bolt.
View detail
It equipped for the involvement prevention to the interference with a Rear suspension and the Tire at the time of using a Side bag. It is a Beauty, and a Plating does not spoil the whole appearance Balance in the state without a Side bag, either, but is
It equipped for the involvement prevention to the interference with a Rear suspension and the Tire at the time of using a Side bag.
It is a Beauty, and a Plating does not spoil the whole appearance Balance in the state without a Side bag, either, but is good touch.
Where a Center stand is stood about single-sided 15 minute, it equipped with
working hours.
When letting the Bolt of a Rear-suspension portion pass, the hole with a Frame shifted, and a Bolt did not pass, but it got impatient, but it succeeded by letting a Bolt pass, raising a car body.
Although used together with the Rear carrier, die length was not necessarily insufficient with an especially satisfactory pure Bolt again.
View detail
Fits: KAWASAKI Z800, KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Versys 650, KAWASAKI Versys 650, KAWASAKI Versys 650, KAWASAKI Versys 650, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ER-6f, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg, KAWASAKI Z750 (water-cooled), KAWASAKI Z750 (water-cooled)
[Webike Monitor] Unless there are purchase and this for GIVI Tank lock attachment, it cannot attach to a Tank. It has attached with Ninja1000 satisfactorily.
[Webike Monitor] Unless there are purchase and this for
GIVI Tank lock attachment, it cannot attach to a Tank.
It has attached with Ninja1000 satisfactorily.
View detail
Fits: HARLEY-DAVIDSON XLH883, HARLEY-DAVIDSON XLH1000 SPORTSTER 1000, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SOFTAILFamily
A Black is recommendation if a body color is black. Since it is not conspicuous, it is very good. Indispensable, if the Saddlebag is attached finely.
A Black is recommendation if a body color is black.
Since it is not conspicuous, it is very good.
Indispensable, if the
Saddlebag is attached finely.
View detail
[Webike Monitor] This product was purchased in order to equip with the Side bag. I think that it is appropriate and I will fully be able to use as quality even if it sees from a price. , however this product cannot be attached when the pu
[Webike Monitor] This product was purchased in order to equip with the
Side bag.
I think that it is appropriate and I will fully be able to use as
quality even if it sees from a price.
, however this product cannot be attached when the pure Carrier is attached.
Although tried repeatedly, the Stay of a pure Carrier interferes and the mounting hole of a Back support does not come to a fixed position.
It is replied that the attachment equipped with a pure Carrier is not checked when you think whether to be my skill shortage and Mr. KIJIMA is asked.
The direction which purchases this product generally should also have many directions which consider and purchase loading of a Motorcycle in addition to fashionability.
If it becomes, even if it has attached the pure Carrier, it is sold or I regard the product with which it can equip as notes of being unable to perform simultaneous wearing with a pure Carrier being required.
Since the Design and the function are pleasing as
products, I would like to extend a Stay, or to process and attach a mounting hole.
As
evaluation, I will carry out critical evaluation.
I think that evaluation differs from me for the direction which is not equipped with
pure Carrier.
Because it is a good article as a product.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Since it is a product made from a stainless, it does not rust, and by attaching and removing, since it is easy, pure return can also be performed easily. extension of wiring of a tail or a blinker is also unnecessary -- it is .
Since it is a product made from a stainless, it does not rust, and by attaching and removing, since it is easy, pure return can also be performed easily.
extension of wiring of a tail or a blinker is also unnecessary -- it is .
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Attachment is also dramatically easy in the form where attach to the place (every two right and left) which took the pure carrier and where the carrier of the frame was attached, and it mounts a tail lamp and a blinker, and since processing of wiring is a
Attachment is also dramatically easy in the form where attach to the place (every two right and left) which took the pure carrier and where the carrier of the frame was attached, and it mounts a tail lamp and a blinker, and since processing of wiring is also unnecessary, it is good to be able to return to a pure style at any time.
Although it runs in rainy weather in many cases for the product made from a stainless, O does not rust at all, either.
View detail
A design which does not break down the style of a motorcycle in the state where the back is not followed, either is wonderful! Since it supports again so that it may not involve in firmly when a back is attached, he can feel easy very much! The texture of
A design which does not break down the style of a motorcycle in the state where the back is not followed, either is wonderful! Since it supports again so that it may not involve in firmly when a back is attached, he can feel easy very much! The texture of plating is also high-quality and wonderful! View detail
![Fitting For Mono Rack [359FZ]](https://global.webike-cdn.net/photo/article/30/1285509662530L.jpg)
Although the cut of a rear cowl is required to attach to a phasor, Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm, Since it appears in the instruction manual and the perforated line is contained also in the cowl side
Although the cut of a rear cowl is required to attach to a phasor,
Every one right and left, 2 cm x about (it goes out simply with nippers) 4 cm,
Since it appears in the instruction manual and the perforated line is contained also in the cowl side from the beginning perfectly, the place to cut for true -, [ easy ]
That there are two stars (although looked in, to the extent that it does not understand) which are not known by any means if it does not look in from the bottom even if cutting [ which wages had as I have you attach in a store / which is not ] temporarily goes wrong,
Although the drilling accuracy of the attached parts made from aluminum having been open at the place bad shifted for a while and these parts become a form inserted in the frame by the side of a car body, it is the point which only a few had to correct with the stick file greatly (it is aluminum, it deletes immediately and can correct).
View detail
Fits: HARLEY-DAVIDSON Universal
The side bag was attached to the muffler side of a shadow classical. Since a bag would contact a muffler if it attaches ordinarily since there are two mufflers, I had the slide rail attached upward. Since a rail would contact a sheet if it sits do
The side bag was attached to the muffler side of a shadow classical.
Since a bag would contact a muffler if it attaches ordinarily since there are two mufflers, I had the slide rail attached upward.
Since a rail would contact a sheet if it sits down, I had you delete and process it by attaching upward.
View detail
Fits: HARLEY-DAVIDSON Universal
Although only the left was attached to SUPOSUTA for saddle bags until now, right-hand side was also purchased to the seat back's fixation. If the both side is attached, it can use also for a touring net, and it is convenient.
Although only the left was attached to SUPOSUTA for saddle bags until now, right-hand side was also purchased to the seat back's fixation.
If the both side is attached, it can use also for a touring net, and it is convenient.
View detail