Reviews
I use it for Fuel Filter for BALIUS.
BALIUS is a motorcycle that is difficult to install a fuel filter because it sometimes stalls like it lacks gas when using PaperType or other mesh type filters depending on the individual variability of the vehicle and the condition of the intake system. However, after changing to this filter, I have not experienced the gas shortage condition even once, and it has settled down now. View detail
It's cheap and it's good.
I think it will be disposable, but I can see the flow rate of Gasoline, and I can also see if there is Garbage or not, and I can see the Hadrill, but I don't know for how long, but this hand may eventually become invisible with yellowish brown. I don't know how long it will last, but I am satisfied with the price, which is quite low. Of course, it is easy to install, and the two-stage hose mounting is a big help. View detail
PinGelPlate
It is essential to install PinGelCook. View detail
PinGelCook!
fcr33πI changed to PinGel to install the carburetor because of the Gasoline flow rate, even though the OEMCook does not interfere with it. The main purpose of this project is for appearance, but… I think it's a good idea.
As other reviewers have mentioned, the hole on the tank side has to be cut down a little to make it larger.
I have wrapped a couple of rolls of seal tape around it and I am happy with it, no gasoline leaks and better parenthesis. If it were a little cheaper, I would have no complaints.
View detail
Fine rust powder passes through.
Take it for a spin on the Hose from the Fuel Cock to the Carburetor. It is better than nothing. By the way, the rust powder of Tank passes through and enters the carburetor. Plastic deteriorates quickly over time, so we keep some in stock in case it breaks down. Replacing the fuel Pipe is quite tricky as it seems to be a simple but important part. View detail
The packaging is too messy.
The product itself looks good and well made, but the packaging is too messy. When I opened the box after receiving the product, the product was out of the Package.
The package was stopped at the four corners and at the stapler, so it was not popped out during shipping or anything like that.
I am concerned that there may be a defect as it seemed to be rolling around in the corrugated cardboard when it was given to me by the shipping company.
View detail
cheapness is the name of the game
I think it is possible to find OEM parts, but the Breather Hose 650mm 6mm Diameter from the rear of the crankcase of CUB series engines was out of stock, so I substituted it with this one of the same size.
I don't want to be speculative, but this Hose in a different Size was falling apart after a year, so it might be better to buy it if you want it for now with the intention of replacing it frequently.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
Way bigger than stock
When receiving this fuel petcock I had no idea how much bigger you could go until I seen it.flows more fuel and perfect for my zongshen 190cc engine View detail
Fits: HONDA CUB-based Engine (CD), HONDA CUB-based Engine (CL), HONDA BENLY90 S, HONDA BENLY50CD90, HONDA MONKEY, HONDA APE 50, HONDA MONKEY, HONDA GORILLA, HONDA APE 100 TypeD, HONDA GORILLA, HONDA APE 100
Used in MONKEY
In this case, we are using 88? but it is also sufficient to supply 115? Motorcycle.
If you bore up, this is safer than OEM.
View detail
Super fuel hose set I.D.Φ3×1m
Used for carburetor overflow hose
I bought Pink last time but 1m was not enough so I bought more.
I decided to use a two-tone color anyway, so I went with Green this time. It is now easier to visually inspect each cylinder.
Now we can also verify which one is more durable. v
Compared to Pink, which is squishy and easy to handle, Large is harder. It is almost as hard as a normal Vinyl type.
Pink is easier to handle (it is soft and stretchy, so you can get a little bit of mouthfuls in the SizeOver area), but either is fine for Overflow.
Green is recommended for use in areas with tight bends, where the pipe is not easily crushed.
As a side note, I always reserve KITACO's Package (plastic) because of the above etc.
It can be used to make a washer for the gap between the clutch lever and holder when there is more play between the clutch lever and holder, or to make a collar to prevent sticking between the accelerator grip and switch holder. And it's free.
View detail
Improved handling
[How is it used?
I used to use DAYTONA's Filter, but I was concerned about the handling of the Hose, so I replaced it with this product.
We chose this product because it is 8mm compatible and L-shaped.
Was the one you received as per Image?
It was just like the picture.
How was your experience with it?
The L-shape allows for more flexibility in the Fuel line.
I have not started using it yet and do not know if it is Catching the garbage, but the Filter is solid and seems to be working fine.
The transparency is better than DAYTONA's, so it is easier to check the internal condition.
[Points to note]
Note that there is a mounting orientation.
The body and package are clearly marked, so be sure to check them before installation.
How did it compare to other products?
As mentioned above, it was replaced from Daytona's Filter.
I don't know if there is a difference in the ability of the system to handle the same amount of power, but so far I am satisfied because I haven't had any jamming or overflow.
【Review】
It is an L-shaped Filter and relatively inexpensive.
I am satisfied so far, as it is easy to check the internal condition.
View detail
Fits: KAWASAKI Z1(900SUPER4), KAWASAKI Z2(Z750FOUR), KAWASAKI Z2(750RS), KAWASAKI Z900(KZ900), KAWASAKI Z750-D1(KZ750D), KAWASAKI Z650LTD, KAWASAKI Z1000(Air cooling), KAWASAKI Z1-R, KAWASAKI Z1-RII, KAWASAKI GPZ1100, KAWASAKI W1 SA, KAWASAKI W1 S, KAWASAKI W3, KAWASAKI 650RS
Gorlancook for Z1
On and Reserve are clearly visible and beautiful in appearance. View detail
Size is exquisitely good
I have been using Fuel Fliter for a long time to avoid clogging and trouble in the carburetor due to foreign substances in the fuel. View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, Others CRcarburetor, Others FCR Carburetor Bodycarburetor
Not bad to look at.
It is inexpensive, but not badly made. Durability does not seem to be a problem. View detail
Quality is high, but care must be taken with Size
[How is it used?
I wanted to install ACTIVEStraightOil cooler on XJR400R, but I did not like the color of the mesh hose. For some reason, there was a Round Type with a black mesh hose, so I decided to install it as a DIY project.
How was your experience with it?
It functions well as a Heat Shrink Tube. The shrinkage is also relatively Smooth, so it is good in terms of quality.
How did it compare to other products?
It is just a Heat Shrink Tube, but it is colored to match the heat resistant hose, so it is more black than other manufacturer's products.
As for the price, I think it is a little high, partly because it is ACTIVEBrand.
Inevitably, I had to buy more, which was a moderate expense.
[Points to note]
StraightOil cooler was #6, so I bought this one #6 as well, but it was a mistake.
The Heat Shrink Tube is passed through the heat-resistant hose from the top of the mesh hose after the fitting is removed, but the hose is too exact and does not pass through properly. If you try to force it through, the mesh hose will get frayed and it will be a large disaster.
I thought it would be easier to buy #8Size because it shrinks when heat-shrunk.
I used a 19Φ made by DAYTONA in combination with the 19Φ and was able to pass it through the mesh hose without getting caught.
It would have been nice if the manufacturer could have provided a little more information about this area, but I doubt that many people would install it as a DIY project in the first place.
View detail
สวยงามตรงปก จัดส่งตรงเวลา View detail
Mk2 with tmr36 and PinGel6000
I installed a tmr36 on a mk2, and the OEM cook completely interfered with the installation, but with a 6mmOffset PinGel6000 mounted slightly to the rear, I was able to complete the installation without any problems. View detail
Super fuel hose set 991-0311000
Used for Carburetor lower overflow hose.
This is the case in the Parts List. (mk? was it?) I thought the inner diameter was 3.5mm, but the alternatives from Company P and Company D were also 3mm, and KITACO did not have half as many, so I bought 3mm. KITACO also did not have a half-decent number, so I bought the 3.5mm. I bought a 3.5mm diameter pipe because it is soft and easy to use.
I liked the Pink color, although the slightly firmer Green would be better for Flow Hose.
When I tried to replace it, I discovered the problem:1m is Quantity.:I can only take 2pcs.
Plans to reorder. I'll have to write another tiresome impresario. I have no time to be poor.
Should we try a Pink/Green two-tone color at this point?
View detail
Clear hose 105-075
Used for Breather Hose 650mm 6mm Diameter for open battery.
Is the name right? It's the Hose that's down from the side, pulling out the Gas.
My Z needs a long length to hang down to the bottom of the exhaust system. (There is also a turn along Tire house) The hose that comes with the Battery is not enough at all.
The price was almost the same as the material store, which is good.
The construction is fine, thick-walled and thicker (8" OD), so it was difficult to pass through in some places, but no problem. It is better than the cheap ones.
Incidentally, I tried an inexpensive Silicon tube once before and the entrance side fell apart in less than a year.
View detail
Cospar good
It is practical because you will not notice the Rust in the Tank going into the carburetor. View detail