Reviews
In order to use imitation parts, although purchased, also with scissors, it is easy to cut, and was very easy to carry out processing this time. I would like to ask, when there is an opportunity to use again.
In order to use imitation parts, although purchased, also with scissors, it is easy to cut, and was very easy to carry out processing this time.
I would like to ask, when there is an opportunity to use again.
View detail
It is used for the Full cowl made from a CLEVERWOLF.I was troubled by the heat of a catalyst although it was used having processed the Cowl corresponding to un-[ catalyst ]. It was in the state which a Undercowl burns with the heat of a catalyst i
It is used for the Full cowl made from a CLEVERWOLF.I was troubled by the heat of a catalyst although it was used having processed the Cowl corresponding to un-[
catalyst ].
It was in the state which a Undercowl burns with the heat of a catalyst inevitably and a hole is likely to open.This product was discovered at such time.It is a famous Manufacturer called
DRC and is reliable.It purchases by prompt decision.The
rear face is a powerful Tape and attachment is dramatically easy.The form of a Cowl can be made to fit that it is easy to cut.
It is used for a Circuit run, checking durability from now on.
View detail
[Webike Monitor] When it stuck on the whole Tank bottom, it stopped feeling heat also in the midsummer, although afflicted by the heat of the inner thigh by the temperature rise of the fuel tank. When it rode in the Jeanses before wearing, it was
[Webike Monitor] When it stuck on the whole Tank bottom, it stopped feeling heat also in the midsummer, although afflicted by the heat of the inner thigh by the temperature rise of the
fuel tank.
When it rode in the Jeanses before
wearing, it was red like a burn with a slight inner thigh, but the Long touring was also canceled after wearing.
Since the
rear face is an adhesive face, it can stick easily, and since a Cut can also be simplified with scissors, it can stick without a crevice.
In the case of
large-sized Motorcycle, the whole bottom with two sheets can be covered.
For
appearance, custom-made one which it does not understand raised comfortable nature markedly.
View detail
It has a rectangle of 5 cm x 100 cm, and since the flesh side of pasteboard is paper, it can use a Magic. since -- it is best to make and cut off a model. Thickness was stuck inside the Undercowl so that it might not melt about 1.5 mm with the heat of t
It has a rectangle of 5 cm x 100 cm, and since the flesh side of pasteboard is paper, it can use a Magic.
since -- it is best to make and cut off a model.
Thickness was stuck inside the Undercowl so that it might not melt about 1.5 mm with the heat of the
[attachment and the effect
] and a Muffler.
The marks where the Cowl and the heat insulating material burned are nothing so that the heat-resistant effect may be enough.
It stuck on the Carbon sheet of
.0.3mm, and stuck it on the Rear frame.
When it sees targeting the exothermic fall from a Frame, heat is felt although it came to touch empty-handed.
Since it was thick, the
[general comment]
and thickness have expected that the heat-resistant effect was 1.5 mm.
Since it is merely a rectangle, it is troublesome to make a form.
View detail
The heat interception sheet etc. were not Attached to the latest Motorcycle under the Tank in many cases, and since it was hot anyhow, it stuck to protect wiring and fuel from heat. Although scuffing was conspicuous for a while, there
The heat interception sheet etc. were not
Attached to the latest Motorcycle under the Tank in many cases, and since it was hot anyhow, it stuck to protect wiring and fuel from
heat.
Although scuffing was conspicuous for a while, there was a paddle which a Tank is not directly [
] in charge of wiring, and grew into it.
It will be saved, if it is thin to a slight degree and cheap.
View detail
Since a muffler and cowl were near, I purchased for preventing heat purpose. It is as expected.
Since a muffler and cowl were near, I purchased for preventing heat purpose. It is as expected. View detail
Since the accident in which it melted in an instant when a rainwear is equivalent to a muffler, since the muffler was replaced with the custom muffler occurred, in order to carry out somehow, it decided to roll this tape. Melting at the moment of [ th
Since the accident in which it melted in an instant when a rainwear is equivalent to a muffler, since the muffler was replaced with the custom muffler occurred, in order to carry out somehow, it decided to roll this tape.
Melting at the moment of [ the ] touching safely, although it was operative was lost.
Although it was good, even if it rolls this, to the extent that it cannot touch by hand yet becomes only temperature.
Don't you carry out as perfect heat insulation as a pure muffler?
This product is a double-stick tape type in practice, although wire is reflected with the photograph.
It is better to check in written form firmly.
It is the adhesive power of the grade of being easy to wind since a double-stick tape type adheres when twisting, and too, if an end is not pressed down with wire, it will separate.
About nine months have passed since it wound, but surface silver separates and a lower white portion is becoming unreserved.
View detail
It purchased for the measure against contact of a radiator hose and an exhaust pipe common to a ninja. after all, since it was low, heat-resistant temperature was not able to be used -- I think that it is effective in the motorcycle of ~ full cowl, an
It purchased for the measure against contact of a radiator hose and an exhaust pipe common to a ninja.
after all, since it was low, heat-resistant temperature was not able to be used -- I think that it is effective in the motorcycle of ~ full cowl, and glow protection of a cowl.
It wants without writing it as the object for mufflers. --
View detail
It purchases on the back side of the big tank of WR250R for thermal insulating processing. It is [ that double-stick tape is also thick solid and it is easy to stretch a curved surface ] very good.
It purchases on the back side of the big tank of WR250R for thermal insulating processing.
It is [ that double-stick tape is also thick solid and it is easy to stretch a curved surface ] very good.
View detail
Work good considering a price is done and there is well. Work is also easy and should just have scissors. I wound around the brake hose passing through the neighborhood of piping of a muffler. Although it is unknown, isn't it profitable which
Work good considering a price is done and there is well.
Work is also easy and should just have scissors.
I wound around the brake hose passing through the neighborhood of piping of a muffler.
Although it is unknown, isn't it profitable which actually works if big sense of security can be got in this amount of money?
View detail