Reviews
Fits: HONDA Forza., HONDA Forza., SUZUKI Sky Wave 250, HONDA phase, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350
It is recommended
Impact wrench mounted in no problem at all
3 KJJOG 's Clutch disassembly unavoidably purchased
When setting again etc etc. I think that there will be opportunities to use again Since it is better to have more tools than less
View detail
I feel relieved.
Purchase to do Initial adjustment of Rear suspension.
I purchased this because the size of Nut was unknown.
I can not rely on making it, but I could use it without problems.
Although it is used less frequently, it will be a problem if you do not have it, so do not lose it.
View detail
Adjustable Pin Wrench
The handle of the wrench is sturdy and has a nice rubber coating on it. The adjustable mechanism is nice and can be hand tightened sufficiently. The pins however are not very strong and a tightly jammed lock nut will cause the pins to bend. I have already bent the pins while opening a lock nut on a damper. However for light work it is quite adequate and price is cheap too Stronger pins would have gotten it a 5 star rating. View detail
"A MUST HAVE" IN YOUR GROM TOOL BOX
The MINIMOTO Lock Nut Wrench is the first part/tool you should buy if you intend to do any workbehind the right crankcase cover. Don't start work without the Lock Nut Wrench. It fits the GROM clutch and oil filter lock nuts perfectly. I used it for Oil Pump upgrade, Oil filter upgrade and Clutch (to Slipper) upgrade. Buy it before, you start lookingat any upgrades under the right crankcase cover. I repeat "A MUST HAVE TOOL". View detail
Fits: HONDA NSR50, HONDA GORILLA, HONDA MONKEY
Can be used without problems
JA 07 Primary side of SuperCUB 110 (Centrifugation) Used for maintenance of Clutch. Pulley holder etc. are necessary to prevent co-rotation, but it was possible to use without problems.
It may be a story limited to SuperCUB 110, but somewhat sitting is bad, as long as the nail length is long. Although it does not matter if used with caution, it is hard to say that it is easy to use.
Because it is cheapest, if you touch the engine around the Honda car, I think you will not lose it if you buy it.
View detail
You can use
Ducati's Rear tire purchased for center nut removal.
Although it is a shape that Nut is not easily hung thinly, it holds firmly in this product.
View detail
Fits: HONDA PCX125, HONDA PCX125, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, HONDA Lead 90, HONDA Lead 100, HONDA Lead 50, HONDA Lead 90, HONDA Lead 100, HONDA Lead 50
After all exclusive Socket.
Until now I had properly tightened with NutWrench, but most of my acquaintance purchased this Socket because it would be better to tighten with Torque wrench.
If you think about that, that's right... Because it is part of Large thing...
By the way, when you loosen it, Impact is nothing!.
View detail
I bought it for Maintenance around Steering.
Since there are two Motorcycle, Size It is possible to use it steplessly. With the thickness of the moving part, the tool does not enter with the Top Bridge attached. After tightening with this, tightening Nut of Top Bridge was too hard and could not be adjusted easily. Once it was tightened, loosened, tightened, it became in a condition that it was convinced by delicately adjusting it the first time after tightening the Top Bridge.
The tool itself is solid and easy to use.
View detail
Adjustment of Mono Suspension
I used it for the SRX 250 F, I purchased Small Type Wrench because the space is small, but Hook could not move properly. Perhaps my way of doing things was wrong, but I think the Fixed Type is easier to put power. I can not adjust it after all.
Perhaps, it may be good to do it after you have gone sideways and remove some parts you can remove more. I'd like to try again if I can do it..
Even so, because the price is the price, it may be a good product depending on the Motorcycle.
View detail
Special tool
I was riding the car at the time of shipment for about half a year, but I wanted to adjust slightly and purchased it. It is hard to adjust the position slightly, but there is no problem.
I think that there are not many occasions to use, but these tools themselves have never been better than nothing.
View detail
Custom 中 ♪
I bought it for Rose to paint Front fork.
Without this tool, it was very handy as it could not be removed ♪
However, it would have been better if the part of possession was a little longer.
View detail
For Rear suspension adjustment and Stem tightening
Purchase for Inarial adjustment of Rear Suspension and tightening of Steering stem.
Since Size is also small, it is not an obstacle to put it in a tool box for carrying in Circuit Size.
For FreeNeck, you do not have to adjust the Hook position depending on the place you use.
View detail
For Clutch nut
I am using it for Scooter's Clutch nut.
Because it is thin Nut carefully with ordinary socket? If it is chamfered, it is easier to tear back, so it is not chamfered
I think that this product is easy to use even on that point.
View detail
Purchase for Stem
Until now, Steering - I adjusted tops red with hitting hanghang with Slotted screwdriver, but I wanted to graduate from such a weak work and purchased it.
When I actually used it, I thought that it was better to have it after all.
Slightly closed condition is not felt by Slotted screwdriver.
Thanks to this, it has always been decided by one shot that we fine-tune the closing condition as many times as usual.
Although it is a tool with less use frequency, I was keenly aware that it is absolutely necessary tool.
It is recommended because the price is cheap, too..
View detail
Cheap, easy to use, sufficient
At the beginning of the purchase, I felt uneasy about the cheapness, but when I try it, I can recommend it as an Large carpet that is just right for rear suspension adjustment, as an in-car tool. Finishing is complicated, but it would be suitable for the price. View detail
Good for using for the time being ....
Although Cost is cheap, it is attractive that it is cheap, but because Firefox moves, it does not engage well and it is not easy to use. It is convenient to use for a while because I wanted to use the adjustment of Rear suspension of XL 1200 C SPORTSTER 1200, but if you know the Size to use, it would be better if you purchased that Size's.
However, because it is not a frequently used tool, I think that this Cost is a good product if it can be used widely. In my case, I do not even know Size and I did not like it if I could not use it after purchasing, so I bought such a worried one.
View detail
Clutch and centrifugal filter required for desorption
It is necessary for detaching Clutch and centrifugal filter
When using this item for Grom, 12. If it is not 7
Since the centrifugal filter Shaft is long 9. Please note that Shaft can not be used in 5
12. Shaft somewhat hits even 7, so I need a bit of hang
You can definitely detach Lock nut!
View detail
Fits: HONDA NSR50, HONDA GORILLA, HONDA MONKEY
First time Clutch exchange
Buy for the first time trying to change Clutch. Clutch It is an indispensable tool if you exchange it. I am out of a variety of Manufacturers, but this was the one I chose. I tried using it and used it for Smooth. Although it is for manual only, it is Sunday mechanic so we will not use Air Impact.
It is good for Cost performance.
View detail
Although DUCATI HYPERMOTARD 796 was a cantilever Swing arm, in order to carry out the increase bundle of the big Nut of a Rear wheel, the 46-mm Socket of the DAYTONA was purchased.Although the use of the original product was a thing for clutch pulleys, it
Although DUCATI HYPERMOTARD 796 was a cantilever Swing arm, in order to carry out the increase bundle of the big Nut of a Rear wheel, the 46-mm Socket of the DAYTONA was purchased.Although the use of the original product was a thing for clutch pulleys, it has been satisfactorily used also for the Rear-axle Nut.
Although it was 46 mm and a huge Socket, since it was accurate, it was easy to impose a Torque and it has worked in comfort.It is just going to call this hit product made from a DAYTONA truly.
View detail
Fits: HONDA Forza., HONDA Forza., SUZUKI Sky Wave 250, HONDA phase, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350
It is a big 41-mm Socket required to exchange the Rear sprocket of DUCATI HYPERMOTARD 796.In tool store, when it became this Size, there were many products offered for Impact wrenches, and the Socket thought that it became deep and was probably hard t
It is a big 41-mm Socket required to exchange the Rear sprocket of DUCATI HYPERMOTARD 796.In
tool store, when it became this Size, there were many products offered for Impact wrenches, and the Socket thought that it became deep and was probably hard to use, and purchased the Socket for the clutch pulleys of a DAYTONA.
Is it because it is a DAYTONA that structure is comparatively [ cheap ] solid?Even if actually used, it was easy to apply power and was an easy-to-use tool.
Although it was a seldom used tool, I thought that he bought a good thing.
View detail