Reviews
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
There was a Gasoline leak.
Previously, I bought it from another company and it was leaking after about 5 years.
I have been driving MONKEY for about 13 years and this was the third time I had to replace it.
View detail
DAXAir cleaner
Good cosmetics,
Mounting Bracket Location OEM and
Spacers are not required because of the difference.
View detail
Fits: HONDA Shirley 50.
CHALY s Cook was broken.
CHALY I purchased this product because the Cook of Last time I had another CHALY I purchased this product in the first place and had no problems at all, so I purchased it again. View detail
It was very good!
The price is low, but the quality is very high and I had no problems at all with the installation.
I am considering purchasing another bottle in Stock!
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
good
I think it is worth buying because it can be used for various types of cars!
It would be nice to have one, especially for a 4MINI, as it will be used more often!
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Minimoto MONKEY Handlebar Clamp
I purchased this product because I replaced the 6V OEMMONKEYFront fork with a 6V GORILLA, and I wanted to install the HURRICANE Mini condor that was attached to the GORILLA, but I knew that the for MONKEY Top Bridge cannot be attached to the GORILLA's Handlebar Clamp, so I purchased this product. I decided to purchase this product because the position and diameter of the mounting holes of the Top Bridge are different between MONKEY and GORILLA, and the price is reasonable. When I installed the Handlebar Clamp, the position of the Handlebar was about 10mm forward, so I can use it without any problem. View detail
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
Maintenance of Chain, which I am not good at, could be easier.
I've only done simple cleaning when I sprayed oil in the past, so I think I can do it a little better from now on. View detail
Low price but sufficient Quality
The price of Motion pro was too high, so I went with this one. The price is a quarter of the price, but the quality is solid and this product should be sufficient. The box is just a bonus, and the lid closure is so roughly made that it won't close after a few uses. View detail
MINIMOTO Regulator from 6V MONKEY Silicon Rectifier
I installed it on my 6V GORILLA, I bought it to customize it with 6V, the voltage is very stable and the battery life is longer. I will continue to ride on the Large Cutter while maintaining it. It has been my partner for more than 40 years. View detail
Getting the Center out is the hard part.
I was prepared for BALI and Small scratches, but I can't get the Center without modifying the Brake Panel side.
I also bought a 4mm Sprocket spacer but I think it will be useless.
Also, there is some distortion, so if you want to assemble it tightly, we recommend a reasonable price.
View detail
Great tool, highly recommend
This way is much more precise. Works like a dream. Bought this tool for removing the small KTM Bendix bushings. It worked perfectly. Great tool for the price, was able to remove all of my bearings from my transmission in my KTM plan to rebuild my KTM with it as well, didn't have an issue with any of the small sizes, you just have to be sure that you are setting it up properly. Note that you'll need up to a 26 mm wrench or a crescent wrench. Seemed a little pricey for a tool you do not use that much but it will serve generations of riders in the family. Tips: Don't forget to grease the sockets, center them exactly and tighten them. View detail
In the Chinese VM Setting
[How is it used?
For some reason, Throw of Chinese VMcarburetor has this Type, so I used this one for setting.
Was the one you received as per Image?
The Sponge dividers were quite nice compared to the usual divider-only Packages.
It is good because Jet does not mess up inside.
Was the installation difficult?
Accuracy is adequate. There were no problems.
How was your experience with it?
Smallest SizeQuantity for SmallEngine Displacement Volume:I thought that with Set, I could Cover all of the Setting range.
It is said that OEMs are more accurate and better for jets, but if the mother company is a Chinese carburetor, I don't think it will be a problem.
[Was there anything that disappointed you?
None in particular
View detail
MINIMOTO6VMONKEY Silicon Rectifier Fire to Regulator
I have two 6V GORILLAs, so I installed the first one and the voltage became very stable and the battery life improved dramatically, so I installed the second one as well. I did not want to change to 12V, so I bought it to keep driving with 6V. View detail
Universal but...
I was looking for a Universal Oil filter wrench and found this one.
Compared to other companies' products, we chose this one because it can accommodate a large diameter.
In fact, I used it for Oil replacement and found it very nice that the Socket is compatible with 9.5 and 12.7.
However, the part that grips the Filter is still bare steel, so it will scratch the Filter when tightened.
The Oil Filter is basically out of sight, which was a little disappointing.
View detail
Universal Product
I bought it to clean the parts that were soaked with oil.
It may be a little soft, but I will adjust it by cutting it a little.
View detail
Well, it is about the same price.
It needs a little processing, but I think it's a good cosmetic product. View detail
Pipe Handlebar/Clamp, but as a Fog Lamp/Clamp.
I was looking for a clamp for the Fog Lamp, and since the Pipe diameter is 22mm and it is an M10 Bolt, I thought it might work, so I did some research and found that it might work, so I purchased it.
I wanted to hang it straight down from Clamp, so I was satisfied.
Of course, Bolt and Nut are purchased according to their length at the time of installation.
View detail
For ChainSelfMaintenance
I had been doing maintenance of the chain by myself, but I was not satisfied with the results, so I decided to purchase the equipment.
Both parallel and perpendicular can be checked.
Analogous method, but therefore reliable.
I think it is a good item to have, and I recommend it to those who do maintenance of looseness and deflection of a chain by themselves.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Required for Carburetor setting
Packing is essential for carburetor setting, etc., which requires multiple carburetor body roses.
Quantities, since rubber packing usually dies when opened and closed before aging.:It might be nice to have at least 2 Sets.
View detail