Reviews
สินค้าและบริการถูกใจ ต้องได้ใช้บริการอีก View detail
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX1100
Due to the deterioration of the Rubber
I bought it because of the deterioration of OEMRubber.
The "snap" sensation is eliminated.
After installation, it is not visible at all, but the effect can be felt.
View detail
go around moderately
[How is it used?
I usually compete in Enduro races, and I have been tightening the brake master and lever just right because breakage of the brake master and lever can lead to DNF. If they were tightened solidly, there would be no place to escape from the force of the fall and they would break.
It is a Torque that does not break, but it tightens to the extent that it moves Limit if you lack strength by hand. Sometimes it is very loose, and if you mess it up, the Bolt can get lost.
This product can be fixed by inserting Nylon or some other material so that it will not slip even when well tightened.
Was the one you received as per Image?
As shown in the image. The surface is a little rough. It is natural because it is written "Sand Blast Finishing".
Was the installation difficult?
Simply replace the OEM Clamp. It should fit most Brake Clutch MASTER Clamps since it has a slightly longer hole.
How was your experience with it?
I used to do TorqueCheck before races and practice, but now I don't have to do it anymore. I should have bought it earlier.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
ACERBIS:ACERBIS TRI FIT Hand Guard (https://www.webike.net/sd/21204398/) This is also Torque enough to turn when force is applied, and if the bolt is tightened, the entire MASTER will turn around so that it will not be damaged. It will not be damaged. This is a recommendation as a hand guard to be used in combination with the MASTER.
View detail
Fits: Others , HONDA MONKEY125, HONDA CL250, YAMAHA XSR125
Fat type
The cheap-looking part of genuine parts can be changed a little more luxurious. It's a bit expensive, but it's perfect for color! View detail
![[Optional Parts] Lever Guard Spacer](https://img.webike-cdn.net/catalogue/images/21889/spacer1_TS.jpg)
For LeverSpace adjustment
Brake and clutch lever are inside the bar end.
OUTEXLever Guard is not a problem if you have
It will be attached directly to the Handlebar End, so it will be attached to the Bar End a little bit.
I wish there was a color setting since the Spacer is Silver on the ground.
View detail
30?
XSR155 with DAYTONA Mirror.
The Right Side looks good without this product, but the Left Side shows the body about half of Mirror.
With this product attached, it has become very easy to see and anxiety free.
View detail
Used in XSR155
I found this product when I wanted to do something about the fact that my body was quite visible in the Mirror on the Left Side.
As a result of the installation, the problem was completely solved. I am very happy with my purchase.
View detail
That's the exclusive product
I bought this for a Holder for my phone exclusively for the SV650X.
It's a special product, and it comes with a firmly!
The Installation Instruction Manual says to remove the Master Cylinder, but I was able to install it just by shifting it slightly.
Neck the price is high...
View detail
Ideal for Panigale Bar end mirroring
Used on 899 Panigale.
I purchased this bar end because Panigale has screw threads cut into the handlebar, and if the normal bar end is installed, the screw threads will be crushed and the normal bar end will not be usable.
The Pitch and O.D. were the same as the OEM product.
Note that it is necessary to purchase a Bar end mirrorMirror or similar that matches the Bolt diameter.
View detail
CB250RHandlebar replacement essentials.
CB250R with HURRICANE's BMConti3 type
I purchased this product for installation.
28.In order to get the OEM of 6Φ to 22.2Φ.
Spacer collar is required.
Mounting is only A little on the outer side of the semicircle
Double-sided tape was applied to fasten the gap.
If you don't do this, you will always be in the Best position.
Color cannot be inserted.
Well, that's because it's mostly hidden.
It is not built to be so Beauty.
If I get the chance, I may replace it with something a little better built.
View detail
Good visibility even at 30mm
Installed on MONKEY125
I was worried about 45mm, but even with 30mm the visibility was sufficient.
I hope this keeps you safe.
View detail
Available in a choice of lengths.
Used with HURRICANE SSC Side cap.
I was too lazy to look for it in Home center, so I ordered it together.
I'm a pain in the ass (laughs).
I think this is the best time to add an ExtensionBlock or WeightBlock.
View detail
Not much was needed.
I didn't feel the need for it. I don't feel inconvenienced without them. View detail
Mechanical cruisers
It can be used well enough as a simple cruiser.
However, please note that some motorcycles may interfere with Mirror and not be usable.
I installed it on a Harley, but it interfered with Mirror, so I moved Mirror and installed it.
View detail
cheap
[How is it used?
Mirror is now easier to see.
Was the one you received as per Image?
Yes
Was the installation difficult?
For beginners.
How was your experience with it?
Mirror is now as easy to see as I thought it would be.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
SP Mukawa Handlebar guard
Purchased for mounting a phone holder. I am very satisfied with the quality and the fashionability. View detail
More effective than imagined
We chose side-view mirrors because of their design, but the angle was poor due to the combination of other parts, and we could hardly see the rear of the car...
I installed these Parts on a good day and was surprised to see that the visibility was better than with the OEM Mirror. The Bolt does not loosen while driving and the Mirror does not vibrate.
Worth a try if you have trouble with Mirror's visibility.
View detail
perfectly
It is inexpensive and easy to install.
Mirror now looks better.
View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA CT125
SP TAKEGAWA Handlebar Guard
I looked for the handlebar and bought it because I thought Takegawa's product suited my taste. The installation is simple enough to be self-installed You must have a tool. There's a small screw, so other than that, it's easy I like the product. Sell a lot of good products. View detail
Easy to pull out Pin.
Pulling out the Pin was made easy with this tool! View detail