Reviews
Acceleration changed?
It looks and sounds better. Acceleration also feels better.
However, Oil Filter replacement is no longer possible due to installation error? However, oil filter replacement is no longer possible due to installation error.
It has become tougher to remove the hose on the Oil cooler. O-ring of Oil cooler may be necessary every time.
View detail
Great product
I purchased the RS from a reliable dealer after having driven it for quite a few miles. The previous owner had an AKRAPOVIC Slip-on Silencer and I personally felt the sound was too Large (especially when starting the engine).:The Normal muffler, which I believe is Stainless Steel, was also sooty, so I decided to purchase this beautiful product. The sound is not "quiet" It is not exciting to drive, but I like it very much. The engine characteristics are more obedient to the movement of the right hand, and the torque around 2,000 rpm has been fattened up, making it very easy to control. I also feel that the vibration on the grips has been reduced. It was like a puzzle to remove the coupler from the mount. The O2 Sensor requires a 22mm Glasses Wrench to remove the Sensor. I also installed HeelTEC's CanSera on the coupler that connects to the exhaust servo motor. Without this Can Seraer, the exhaust servo motor must be left on the body. The exhaust gasket seems to be usable as it is (13mm Glasses Wrench is used for the exhaust system bolt), but the exhaust pipe before the silencer needs to be assembled properly in order to install the silencer neatly. Finally, the spring is installed. As an amateur, I had muscle pains for three days. The performance and appearance of the exhaust system is excellent and well worth the price. I wish it had been included in my new car. It is not cheap, but it will make your motorcycle different (my opinion). View detail
Fits: KAWASAKI MEGURO K3, KAWASAKI W800 CAFE, KAWASAKI W800 STREET, KAWASAKI W800
Sounds good.
When installing the silencer bracket on the Right Side, the screws did not go in straight and I had to screw them in with a bad feeling.
The exhaust pipe turns bright Red when warming up, is this like this? It looks like it is about to catch fire.
View detail
Very Nice!
Ordered the Wyvern Classic 4 Exhaust. Items were very well packaged for the trip to the US. Pipes are beautiful and the chrome looks excellent, No quality issues coud be found and I spent an hour going over every square inch. If there could be an improvement, I wish the were double layered at the headpipes, like Honda used to make them, to prevent bluing from the hot exhaust. I have not installed them yet and maybe my concerns will be unfounded after thay are installed. Overall so far, great looking pipes! View detail
Fits: BMW R1200GS Adventure, BMW R1200GS
Wyvern Real Spec
Torque up at low rpm, which is immediately apparent after riding
The sound quality is mellow, and it feels quieter than NORMAL and does not cause sound fatigue even over long distances.
But it's a good price, so it takes courage.
View detail
Fits: KAWASAKI W800
I think it's generally good.
The installation itself is easy, but the OEM rubber on the center stand stopper is large enough to fit.
I gave up and made it myself by buying various things at a hardware store.
The Others are generally satisfied.
View detail
Very good chrome !
I received the package in only a few days. I was astonished how good the quality of the exhaust is, the chrome is perfect in all areas. The exhaust was very well packed and came with mounting material and documents View detail
The sound quality is great.
The OEM Ginkgo bilobaSilencer also sounds pretty good, but it's heavy!
This time Silencer is lighter, sound quality is lower than OEM, and looks a little Pushing up and Short Kan.
I competed with Trickster's Ikazuchi Short, but Wyvern won out in terms of both gold value and design!
I have checked the performance of the Torque for 300kmTouring, Winding and high speed driving, and it is not noisy with the lower Torque.
In the Tunnel, the AxelOff resonance from with RPM is a low, loud sound in the OEM, but the Wyvern was not bothersome.
I would recommend it, as it extends the high RPMs as well.
But Quantity:It will be 2pc, so the price range may not be an option.
View detail
Causes were easier.
I think the construction of the product is very good.
The installation is of the pinching type and requires a little setting to eliminate gaps.
The cause was easier, but there were times when it was slippery or uncomfortable on Asphalt.
View detail
Fits: KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Beautiful browning
First time installing Titaniumium full exhaust!
The baking color is so beautiful, I could look at it forever!
Sound is quiet because of Japanese Government Approved Exhaust System, but you can hear it!
I would like to replace Silencer only at the exit sometime soon!
View detail
Fits: HONDA Rebel 1100, HONDA Rebel500, HONDA Rebel250, HONDA Rebel300, HONDA Rebel300
MTMODEL×OEMWIN deCowl with high installation difficulty
After much research, I found out that the difficulty level of installing a Handlebar Riser increases dramatically just because it is an MTMODEL Rebel 1100, and it has an OEM cowl, which is even more difficult to install.
As mentioned earlier, the MTMODEL has a patched Clutch Wire, so it is necessary to change the handling to a good one, which increases the difficulty to a degree that you cannot imagine when watching a video of a quick Youtube installation repo with a DCTMODEL.
In addition, in the case of my Motorcycle, because it was equipped with an OEMWIN de Cowl, if this is attached, the Cowl is removed and converted to an Exclusive Bracket, and the difficulty of installing ・・・・ and the Handlebar Riser itself seems to increase dramatically, so I recommend that those who do it on their own are familiar with it and are prepared to install it. Therefore, it is recommended that those who do it by themselves should be prepared to install the Handlebar Riser.
I don't see many repos with this Handlebar Riser in combination with MT×OEMCowl.............................good luck to those who do it by themselves.
Also, the Motorcycle store had to cut out a part of the plastic cover where the clutch wire and other wires are located. If there was no OEM cowl, it might have been possible to handle the wires by just routing the wires, but it seems that the wires could not reach the cowl if it was also attached.
As for the conversion after installation, the conversion was that it did not move backward as much as expected. However, it is still overwhelmingly Quantity in the backward and upward direction.:It is true that the bike is set back, and I can now ride with a hunched posture like when I ride a Harley instead of the leaning forward posture I used to have with my arms pinned and stretched. (However, due to my short arms, my arms remain the same as Pin and taut.) 。
It is pricey, but it is effective, so if you can, you may want to put it on about as soon as you take delivery of the car.
View detail
It's pricey, but I like Earls Gear.
There are many cheap STANDBrackets out there, but I bought this one because it is Earls Gear.
The price is high for what it is, but with the increased stability of the Side Stand and the way it looks, I'm somewhat satisfied!
View detail
Fits: HONDA Rebel 1100, HONDA Rebel1100DCT
Required if with OEMCowl
Purchased this for the installation of a Handlebar Riser on an Earls Gear Rebel 1100. I purchased it and requested to have it installed directly at WebikePit in.
It seemed that it was still necessary, and we were able to attach it to Beauty.
The difficulty of installing the Handlebar Riser itself seems to increase dramatically when the OEMCowl is attached, so we recommend that those who do it on their own be prepared to do so if they are familiar with it.
I don't see many repos with this Handlebar Riser in combination with MT×OEMCowl...
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R HAYABUSA
Lighter and easier to handle
More than Power feel and sound quality. (although both have improved). The most important thing was the lightness. When I finished the installation and removed the Maintenance Stand Light! I feel that it is a good idea.
Rear was too light and re-set Spring and Damper.
Also, it's easier to clean the Chain now that it's Single w
View detail
Increased stability when parking
I purchased this to help cause my heavyweight GSX1300R HAYABUSA. It looks and feels good, and the bottom is cut at an angle for stability. Of course, there is no interference with the exhaust system. I thought it was a good stand high bracket. View detail
Fits: HONDA CB1300SB, HONDA CB1300SF
I'm satisfied
At the time of purchase, the product arrived half a month earlier than advertised.
The Instruction Manual for installation was also easy to understand and super simple.
At Idling, it seems to have a little more bass. At high RPM, I cannot judge how much different it is.
My family did not seem to understand that I had changed the exhaust system.
I wonder if it is a mood thing, or if I feel a little better Response.
View detail
Fits: HONDA CRF1100L AfricaTwin AdventureSports, HONDA CRF1100L AfricaTwin AdventureSports, HONDA CRF1100L AfricaTwin AdventureSports, HONDA CRF1100L AfricaTwin, HONDA CRF1100L AfricaTwin, HONDA CRF1100L AfricaTwin AdventureSports, HONDA CRF1100L AfricaTwin, HONDA CRF1100L AfricaTwin AdventureSports
Easy to get up.
AdventureMotorcycle tends to have deep Side Stand angles.
The Africa Twin is a heavy vehicle, and depending on where it is parked, it may take some force to raise it up.
This product raises the bottom of the STAND so that the relative STAND angle is softened and just easier to handle.
It also slightly increases the footprint of the STAND and provides a sense of security.
Great buy, a Commendation product!
View detail
Fits: HONDA CB1300SB, HONDA CB1300SF
The ride quality changes considerably.
I wanted a relatively easy slip-on silencer to change the look and feel of my car, but when I was comparing various manufacturers' silencers, I decided to purchase this new product. I was not expecting the performance, but I was very happy to see that the performance from low rpm was improved. The sound is also good although it is not large. The only regret I have is that the band of the OEM exhaust pipe joints is not very cool. I tried to hide it with a heat guard from Other Brand Product. However, I could feel the performance increase even with the Slip-on Silencer, and I thought that Earls Gear is a good product. If I had the budget, I would like to install the Full Exhaust System. View detail
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1200 R
Full Exhaust System
I had only seen it in images, but I was satisfied when I installed it.
The color and the sound are good for Japanese Vehicle Inspection Correspondence, and it is a satisfactory Exhaust System.
View detail
Side Stand Bracket
Note the order of screw tightening. Tighten the two screws on the Motorcycle side first, then the outer Quantity:Tightening the 2pcs will attach without gaps. View detail