Reviews
safety
Safe and easy to find the power source. When searching for a permanent power source from the vehicle's harness, the LEDs on the body light up to make it easy to locate. View detail
It's for electricians, but Tough
This kind of standard is for VESSEL electric (Many manufacturers are copying it as it is) I think, but after using both, my honest impression is that it's hard to choose between the two. I prefer this one.
The grip with the groove of Beth Cell Type might be a little better to grip with an oil hand, but this one which looks smooth also has a texturing pattern and unexpectedly does not slide so much.
The grip is triangular, so it's easy to turn quickly, and if you need more power, the hexagonal driver shaft allows you to use a tool to turn it.
Heads with Plus notation are Material:Although it is plastic, it is quite sturdy, and although it is necessary to take it easy compared with Penetrating Driver, it is possible to use it enough even if you beat it. PlusMark of the identification doesn't disappear easily either.
If you want to use one to handle everything from fast turning to tooling up and turning with LargeTorque, this is the one for you.
View detail
Very short driver
First for carburetor adjustment (Minus) I bought it because I thought it was convenient for
The overall length of the screwdriver is shorter than that of a standard Stubby Screwdriver, so it is the only choice for tight spaces.
Also, the Clip of Cowl on the underside of the car body (Plus head) You can apply it straight without worrying about the clearance with the ground when you remove the
By the way, Minus side can be used conveniently when prying Clip which is hard to come off.
This small size allows you to use it interchangeably, so you can have both Plus and Minus, and it fits in your toolbox compactly.
View detail
"Normal The sense of security of
It's a very ordinary Driver.
However, unlike very cheap products, there is a sense of security that can be taken for granted without any modification.
Shank and Grip are solid, Plating is clean, and durable. I've been using it quite roughly, but there are no cracks or chips in the grip or the tool tip. The tip is worn out.
If you are not a fan of the thicker grip end for fast turning, this one may be easier to turn.
It's not like a hundred-yen tool or a BALI, but the tool tip has a little edge, so if you use it roughly, it might scratch the object.
View detail
In OHLINSFork's Setting
[How is it used?
I bought this for the OEM Front fork damping adjustment from RSV4 FACTORY.
How was your experience with it?
I used to use the Wrench from Hexagonal Wrench Set, but it was difficult to use.
At that time, I saw other people's impressions and thought it looked easy to use, so I bought it.
Since it is a Driver type, it can be turned lightly.
[Points to note]
Since it is a ball type, you can approach from many angles, but if you apply too much torque, the ball will come off.
Also, I wanted this size for suspension setting, but I bought other size by mistake before, so please look at the size carefully when you buy!
View detail
You can find the power source safely.
This Inspection Tester is indispensable for the installation of electrical components. It is useful to find the permanent power supply or attachment power supply from the harness of the vehicle. If there is a power supply, the LED on the body will light up, so you can find it easily. View detail
Effective in tight spaces
Effective for use under the body of a motorcycle or in tight spaces where there is no clearance. It is easy to turn with just your fingertips, and if you have a firm grip, you can turn it with a strong torque. View detail
Convenient when you want to tighten and remove lightly
[How is it used?
I bought it mainly to dampen the Suspension, along with the other Size, and wow!
I didn't check the Size carefully, so the Size didn't match.
How was your experience with it?
I didn't get to use it in the area I originally planned, but I am using it for simple exterior Bolt loosening and tightening.
If it is a screw of this size, I thought that Torque of the range that can be used with this is enough.
[Points to note]
It's a ball shape, so if you apply force with a high Torque, the head will probably come off. Yes. It will come off.
How did it compare to other products?
This time SizeI bought the wrong one and found a use for it in another place as a result, so I don't think it's particularly necessary if you have a regular hexagon.
View detail
CowlScrew Removal
I wanted something compact for removing Cowl's screws and I found this one, it is very useful for removing and installing screws in places where there is no space or where tightening force is not necessary. View detail
Convenient for battery replacement
Easy to use Size Quantity:The Set is useful for changing the batteries in the Key less key, the thinnest Minus can be used to unlock Wiring from the Coupler, and the tip is strong and unbreakable, so it's easy to use. View detail
Easy to use
The Grip is easy to hold and very forceful and can be tightened and loosened with the Large Torque. The handle is just the right length and is a must-have for motorcycle maintenance. View detail
For OHLINSSetting
I bought this for Front fork DamperSetting in OHLINS.
It's a bar handle type so the tool didn't go in properly.
ANEX A Neck's Ball pointHexagonal WrenchDriver [vs. side 3×120] If you use a ball point, you can set it up with no problem, even if you put it at a slight angle.
A longer Type would have been better.
View detail
It's easy to put effort into.
The grip is just the right thickness to deliver the torque firmly, and since it is pierced type, it is convenient for old, hard screws and screws that are hard to loosen by licking. View detail
This is just the back of the line!
Sometimes when I'm trying to install and remove parts, I can't get the tool in the gap like this! How does it work? I am faced with this situation. Just the other day, I used the Front Tappet Cover of Grom's Engine on SPTakegawa Remove the OEM HexagonalBolt when replacing it with Shiningly's Parts, too. However, when tightening the Cap bolt at the time of installation, the Hexagonal I had a hard time getting Wrench in.
And while I was thinking about further dress-up plans, I was thinking about the Material:Plastic Tank Cover:I've started thinking about replacing it with a certain part of Carbon. In the past, I didn't think much about how to install it, I just ordered it and fumbled with it when it arrived. This time, while looking at the parts catalog, I was able to see where and what kind of bolts were used. Checked. Then, I was surprised. 1 pc Screw in front of Tank Cover is Triple There is a small gap (maybe 40mm from the Stem Nut) between the clamp and It turns out that it's there, and in a position where a normal tool will never fit. I can't take it off or put it on with this, I have to make the Front part RoseRose. I can't access it.
I do not think that I will change the cover even to do so. However, I began to look for tools to see if this Screw can be removed somehow. I searched using various Key words, and I am sure that "Very short. I came across this Tool when I used a Keyword called The height, including the Handlebar, is a whopping 21mm! This could fit in the cracks!
The product I received was so-so in terms of build quality, a little more slender than the KTC and SIGNET. The Handlebar is also very short, about 10cm in length. However, if you put it in the Pocket when touring, it is very Compact. Peace of mind. Various Quantity:There is a set, but I'd like to use the full set with 9 pieces including HexaGon bit. I chose it. It's still Compact enough, and the Bit is supposed to be fixed with Magnet, so it's easy to use It won't drop out and fall out, because in the normal system of stopping with Spring, it would be long. The shortest bit is realized by solving that problem with Magnet. Awesome.
So, still Material:I haven't received the Tank Cover of Carbon yet (waiting for delivery), but I'm waiting for the delivery now. I tried to access the Screw at the same place. The result is as shown in the picture. We were able to get into a gap of only 40mm and turn the screw! I was able to achieve the purpose of this time, but I think the same thing will happen in the future. The possibility of being able to access the place that you gave up because of the inaccessibility of tools increases to Large width. . It's a real Tool in the back!
This product, I chose the one with a straight handle, but it was 15 degrees up or down in the middle. There is also a downward bent handlebar type. I think there are some cases where these curved types are easier to use depending on the position. You can buy Handlebar only, so you can use it for any situation when you have it all. You can do it. As for the Screw, which cannot be put in even with this tool, I really think you have to give up. It is. But I'm not ready to give up without it! This is handy!
View detail
Bit holder
Bit holder with several Hex bits, CompactRatchet and Others, carry the smallest tools necessary
It's useful in times of need
View detail
Bit sockets and
If you have one bit socket, it is very convenient to have all the necessary sizes of HexBit
The HexBolt can be opened and closed freely with the Ratchet wrench
View detail
As an in-vehicle tool
Carry the Bit socket and Ratchet as a vehicle tool
Align the necessary bits and put them in the bit holder
It's especially useful when you change the OEMBolt to a torque-with-hole, etc
View detail
Anything useful
Although I was using the Exhaust System attachment part in Hexagonal Wrench, I was injured in the hand which made it difficult to enter power, but this product can be easily removed, tightened and easy to use, so it can be used for various Bottle something useful doing. View detail
For S1000RR
Because S1000RR or BMW can not remove and replace parts without Hex lobe wrench - - - This time to take Tandem Footpeg - - - I thought that probably I did not even sell it to the Home center, and I got it on the wig Big soon. View detail
It's a tool you can use!
I purchased VIRAGO Carburetor's Float room attachment Bolt as Hexagonal.
When I exchange Jet, I can finish not to remove Carburetor every time, I am very satisfied.
View detail