Reviews
Good Accent
The OEM Core guard was painted about 2 years ago, but the paint didn't last long because the rust was not removed properly and the surface preparation was not good enough. I thought about repainting it, but I thought it would rust again after a while, so I decided to replace it.
At first, I was thinking of Plain ones without Logoetc., but I chose A-TECH because of its low price.
Regarding the product, although it was unexpectedly thin, the finish was good and favorable. The precision was good and the mounting holes were Exactly. It is also finer than OEM, so it will be more effective in protecting the Radiator. I was concerned about the chatter sound, so I thought about using the anti-vibration material that came with the product, but the upper hook is folded back to the point where the core guard is effectively attached to the radiator. However, the upper Hook was folded back so that the Core guard was almost stuck to the Radiator, and the attached anti-vibration material did not seem to fit in the almost no gap. I ran a test run and did not feel any chattering sound, so I decided to use it as it was. Then, in the Instruction Manual, it says [Color] It says to clear paint it, but I'm thinking of using it as is for the time being, and then doing it together when I have a chance to paint something else.
I thought it would be better without the logo, but when I installed it, I feel that A-TECH's logo is a good accent. I guess there are people who like this kind of thing, but for me, I like it.
View detail
Good texture, though fine alignment is necessary.
Material:Since carbon products cannot be bolted on, it is necessary to adjust the position of the tail lamp and modify the position of the holes for the fixed pins. The carbon pattern is beautiful when exposed to sunlight, but it is not noticeable because of its small exposed area (laugh). View detail
Clipping Sticker.
Design is cool. I like that it has flags on it!
It's a clipped Sticker, so make no mistake!
View detail
It's cool, I think.
I received the product and tried to fit it, but when I straddled it, the minimum ground clearance was about 5 cm. I tried to install the white Gel Coating, but it was not pure white because of the BALI removal. It is not usable unless it is painted.
I have a Wyvern two-pipe exhaust system, but if I don't remove it a little, the exhaust pipe hits me.
So I gave it away, unused and new.
I thought about painting it and attaching it, but decided against it because it would rub my stomach every time I went in and out.
I wanted to put it on since I am wearing a LunasoleCowl. It was a pity.
View detail
It looks beautiful and luxurious.
I purchased this case out of curiosity as an accessory case for my motorcycle, but the product I received was so beautiful that I reconsidered using it inside my house. The other one is matte, but this one is glossy, so I think it will get wound if I put hard things in it. In any case, I think this kind of product is hard to find at this price. View detail
It is a cool Accessory Case!
I bought this case out of curiosity because it was reasonably priced and I was thinking of using it as an accessory case for my motorcycle, so I chose the matte finish. The picture is for reference only after I put an expensive Titaniumium Bolt in it. I think it is a quintessence that this kind of product can be offered at this price. View detail
textured good feeling
I have not used it as a shoehorn yet, but I use it as a key holder. It is well made for the price and seems to be unbreakable.:Carbon Style and the beautiful paint job make me cautious, but I boldly use it as a Key Holder. View detail
a little regret
This is a review of z900rs 21 year old ebony color genuine muffler vehicle installation. All A-Tech sticker manual bolts The reason is that even though the product is genuine, the holes did not fit well, so I tightened the bolts and then loosened them. I repeated the attach and reload. Other than that, I had a little trouble aligning the holes, but nonetheless, I installed it without any additional processing. I'm at a loss as I'm thinking of unpacking and installing it again on the ,,, ,,, This is a review of z900rs 21 year old ebony color genuine muffler vehicle installation. First of all, what is the under cowl heat dissipation sticker? A-tech sticker manual bolts are all There are pictures and descriptions in the manual, but it would be better if the pictures were a little more detailed. It is stated that the working time is about 30 minutes, but it took less than 2 hours with two people because it was the first time I installed it myself. The reason is that, despite the fact that the product is genuine, the holes did not fit well, so I tightened the bolts and then loosened them. I repeated the adda. Other than that, I had a little trouble aligning the holes, but I installed it without any additional processing. When I put it on, it definitely looks more full, it's pretty and I like it. However, I am thinking of unscrewing it and installing it again at the next engine oil change interval. It's hard, it's more than that,,,,,,, View detail
I think the installation would have to be done by a PRO.
Currently CB1300SC4 Parenthesis is a good idea, but it requires a sander to modify the bracket, and the only way to install it is to ask a motorcycle shop to do it for you. The wires and connectors are also large enough to put together. The Bracket is fixed to the Radiator, so if it rolls over, the Radiator will be damaged. This time, I had to order a special Bracket to use the STD Blinker. (A-TECH does not do this for us.) The paint on the Bracket is also messy, so I think it will rust quickly. But it looks cool, so it is irreplaceable. It took 6 months after I ordered. I have to endure the long delivery time. Overall, I am satisfied with the product. I like the fact that I can buy it at a lower price from WeBig. View detail
I installed it on my GSX-S1000.
It was said to be for New Model KATANA, but we installed it on our GSX-S1000. Since it was the same engine, I thought it would be large and strong, so I bought it. I was able to install it without any problem as expected. I went to Two-Ring right away and the heat went up a little, but I don't think it's a problem. The design is simple and I like it. View detail
Received and happy overall
There was a 6 mth delay to get product made, but it was made and shipped within approx 2.5 months. Excellent email updating all the way from webike. Product was well packed. I got the black plain and the black gelcoat was a bit thin along a couple of tight edges but quality of glass was good. Holes did not quite line up but very near, and with a bit of coaxing it all went together. I could not get the final pushpin holes to line up enough, so haven't bothered with pinning those. Quite secure without them anyway. Now I can work on the bike without pulling off the large lower cowlings all the time. I do very little cold or wet riding nowadays. I confirmed the fit to OEM upper cowling before purchase. All up I'm very happy with the purchase and the service I have received. View detail
A-TECHRear Fenderz900rs
It is processed with a long hole and can be adjusted to some extent.
Spec. changed or w
View detail
Accessory Case
It was good for the Accessory Case when touring. View detail
It's more like Race ish.
It's just a change in the look and feel of the car, but it raises tension as it sometimes comes into view while driving.
There is some hang in the installation, but no problem Level.
There is a projection on the back of OEMCover, and it meshes with Tank when it is installed, but there is no projection on this, and it did not fit completely when it was installed. However, it seems that it will not come off because it is screwed.
View detail
It's cooler now.
I installed it because I don't have a Fender and I'm worried about mud splash after rain.
I have not driven in the rain since the installation, but I am satisfied because the area around the tire of Rear became cool.
View detail
Under Cowl, etc.
It's small, so it's not that noticeable.
Quantity:1 Set of 2pcs. so Quantity:Pair (for Left and Right) It can be aligned and stretched.
For Pipe frame vehicles, it is also good to stretch it so that it wraps around the Pipe.
It glued more properly than I thought it would.
If you are using A-TECH products, it's good to Appeal.
View detail
The packaging ruins it.
The product is very good, but... I fixed it and installed it, but it's a little wavy... A-Tech, I'm not returning it because you made it for me! The thing is really nice! I really like it....but you, the shipping guy, were very rude to A-Tech....you don't know how to ride a motorcycle. It was easy to install and even came with anti-vibration rubbers. View detail
I'm happy with how it looks! But it's a pain to install!
I'm riding a SV650X 2018, with an S2 Katanacowl on it.
I've been wanting to get one of these for a long time. The reason is that I don't really do any serious circuit driving, I just want to look good and do StickerTune.
It took me about 2 or 3 months to receive my order. It is Corona season and everyone seems to be riding motorcycles and MotorcycleBoom. The manufacturer seems to be very busy, so I think it is inevitable.
I bought the BlackFRP without painting on the assumption that I would paint it myself. But it looks more beautiful than I expected, so I put it on without painting.
Impressions after installation
When you install it, it's pretty plain. Maybe that's the way it is...
If you stand beside it and look at it, it's pretty much nonexistent.
Also, heat will build up, and since there is no place for hot air from the engine to escape, hot air will come from the feet, which is characteristic of Full Cowl Motorcycles. (Well, it is natural because I put Cowl on.)
As a result, I'm taking it off the road in the summer.
Bad points
I've heard rumors, but frankly speaking, one of the brackets didn't attach properly. And I haven't installed it yet. (I'm going to ask the manufacturer about it.)
There is a part where the direction of the Instruction Manual and the actual Parts are different.
It comes with a thermal protection tape, but I have no idea where to put it when I install it.
It's around here! But as a result, it was burnt with hole in another place by heat. Please be careful everyone!
View detail
It's one of the cheaper Other Brand Products!
Used for CB400SF 2016
It can be installed without any problem. Small Size Spanner or MONKEY is required for assembly.
In the Instruction Manual, it was written that the Amiami part is supposed to be painted.
I assembled it without painting because it was troublesome, but originally it was [Color] It seems to be better to paint with Clearetc.
I will paint it when the rust starts to show.
Now I'm wondering to what extent the Carbon part will keep clean.
[Color] Clear painted carbon parts, but I'm worried about deterioration by sunburn and heat.
You can also buy a Guard made by another company for a few thousand yen difference, so you may decide on the Wallet and Design!
View detail
I can grin and bear it all by myself.
The OEM Side cover cracked so I took the plunge and bought this. You may need to use double-sided tape to replace the vibration absorber (?). You might want to prepare Double-sided Tape. I transplanted the original one because it was troublesome.
I remember that the Both Sides combined were almost 100 Grams lighter than the OEM.
It is a little less slippery, so I think it is easier to maintain the posture while turning.
I also like the fact that it doesn't look like I'm wearing Other Brand Product at first glance in a good way.
I'm giving it 4 stars because it takes a while to ship.
View detail