Reviews
The thinning liquid is a Large thing if the procedure is followed.
I tried my first ZDress-up.
After much research and hesitation, we decided on Mirror violet, with the theme of casually shining and glowing.
The first step is to install the wheel, using MDF Scale, which I have used before, and first degrease the wheel thoroughly with Silicon-off.
After the entire wheel is removed, the adhesive is simply applied using Scale while spraying a detergent thinning solution.
I followed the procedure to paste one of the 4 stripes, but it suddenly peeled off, failed, and fell to the ground, unusable! I try to paste one more piece, but it feels slippery?
The cause was that when making the diluent, the amount of neutral detergent was wrong and there was too much detergent, so the adhesive was not strong enough and it fell like a stream...
After adjusting the thinning liquid again, the adhesive strength improved and work proceeded smoothly, but there was no room for error, so we proceeded with caution and care.
After that, I managed to complete the job on all four wheels in one shot, and upon confirmation, a drop or two of detergent in the thinning solution should be enough!
Small diameter wheels have a large bend, so even if you use a dedicated scale, you need to be careful.
The impression of the finished product is quite good, with a very austere appearance.
When the sun is low in the morning and evening and light reaches from the side, Mirror's flamboyance is emphasized. On the other hand, when it is cloudy or at night, it gives the impression of a dull reflection and glow.
The Violet is a darker color, so it is not so noticeable in the absence of light.
I have been using MDF's Stripe for a while now and the durability is excellent, the thickness and quality are definitely better than cheaper ones, but a word to MDF, can you please make the Small Diameter WheelSpec. in a little more quantity instead of just two spare sheets?
Large and Small diameter Wheels with bends require a lot of construction work and hang.
Even with the use of a dedicated Scale, the work was not as nerve-wracking as it could have been.
View detail
I chose it to match the color of the car body.
We decided to put a rim sticker on the Ducati SCRAMBLER to match the color of the car body.
Since MDF had been used for the past three wheels, we chose to purchase MDF this time as well, even though it is a little expensive rim sticker.
I wanted to put up a yellow-colored delicolore, but there was no Variation and only one color, yellow, was available.
There were 18 Rim stickers attached to the two Seats, and at first I could not tell which Size was the front or rear.
The paste was done as described, but it is not perfect.
If you look closely, you can see some distortion, but it does not feel out of place with the Body color, and I hope it stands out anyway to prevent accidents.
View detail
It's solid
Up to now, I had applied MDF Lime green and 10mm rim stripe on the wheel painted black, but now I have replaced the rear wheel with a ZRX1200R one, so I purchased the same MDF rim stripe and reapplied it on the front.
I thought that if I was going to replace it, I would use Makeover, so this time I decided to use a thinner one, 6mm and 4mm, and I thought the thickness should be 6mm and the color should be different, but in the end, I chose 6mm Lime green as the same color because the other colors did not feel right to me at all. I chose the same color, Lime green, 6mm.
First of all, after removing the Tape that had been attached, I felt that the Rim stripe on the MDF is a no-mistake thing. The MDF rim stripe is very firmly attached to the tape. It is not difficult to peel off, in fact, it was easy to peel off without breaking off in the middle, but unless you try to peel it off intentionally or accidentally, it does not seem to come off naturally. For a cheap rim stripe review, see It's peeling off." etc., but this does not seem to be the case with this Rim stripe.
As for the application process, I believe it can be done with the wheel attached to the car body, but I did the work with the Timing with the Wheel removed. I did the work with the Timing wheel removed. I cut out the backing paper for each tape, degreased the rim of the Wheel, sprayed water lightly on the rim with a mist, and started pasting. When pasting, hold the tape so that the Start position does not move, and trace the tape with the belly of the finger of the opposite hand so that the water drains from the adhesive surface. Finally, warm the Tape with a dryer to make it adhere to the Rim. If you pull too much when applying the tape, the finished circle will be rattled and the adhesion of the sticking part may be weakened, so be sure to adjust your strength. However, the thinner the tape becomes, the more easily it is affected when it is pulled. Also, the overlapping area should be even etc., and since there will be a gap between the tape and the rim above the overlapping area, it is important to warm the tape firmly so that it adheres to the rim. The finished product was generally as I had imagined, and I think it would have been white even if I had made it 4mm.
View detail
Attached to Ducati SCRAMBLER
I bought this to attach Rim stripe to my newly purchased DucatiSCRAMBLER.
Size is 17&18-inches Color to match the car body color:YellowSingle Body 10mm width was chosen.
I wanted to start pasting immediately, but I don't know which wheel to paste the 18 separate tapes on.
There is no mention of this in the Instruction Manual.
Are the top 8 sheets in the front FOR 18-inches or FOR 17-inches?
Are the two spare sheets the last two on the front or the back?
Are you asking me to paste it in the right way?
As a matter of urgency, I inquired through MDF's Home page.
I have not received a reply yet so I am unable to paste it.
View detail
Name Chain
Since it is a black wheel, it was installed together with Tire's WhiteLetter as one point of reference.
Degrease and apply the paste with soapy water, being careful not to stretch the paste by pulling it.
Maybe it would have been easier with a special tool. I don't know.
Tire is much easier to work with if it is free to turn.
View detail
It makes a huge difference in the ease and cleanliness of the work!
I thought it was the right decision to buy it, even though it looks chubby.
Using this, I was able to apply it neatly without the need for water application.
View detail
It's a quick and easy way to give a new impression!
MDFRim stripe affixed using Gauge.
If you are going to paste without using Gauge, you will need to apply it carefully with water, but if you use Gauge, you can apply it beautifully without using water.
You can easily change the look and feel of the original Motorcycle and feel a sense of self-satisfaction!
View detail
Rim sticker
Easy to put up.
It sticks well.
Quite sturdy.
View detail
In Black wheel's Accent.
The black painted wheels looked too heavy, so we introduced rim stripe.
I was confused with Titaniumium color for a long time, but the one that goes better with my ZEPHYR color is
I figured it would be the Blue one from Delicorol, so here it is. 。
This may be due to the fact that I did not use RimGauge when pasting.
If the overlapping dimension of the connection part is about 10mm, the last overlapping part overlaps by about 30mm.
I reposted it. 。 Maybe without RimGauge it would unintentionally pull and stretch when pasting?
The color overlap part here is the "Colored" part, so the above problem will not be so much of a problem if you make the spec. overlap in the "Black" part....
View detail
One point on your feet.
Purchased Black6mm.
I bought it as a One point kind of thing, but I think it could have been a little thicker.
The workability was good, and since we purchased the special Gauge, installation was easy.
It would be troublesome without a dedicated Gauge. (Quantity):(Set should be sold)
I am satisfied with the product.
View detail
Finally, it's sticking!
I switched to GSX and first bought MDF Rim stripeM6 Red.
As per Instruction Manual and You Tube videos
Degrease firmly.
Spray lightly with a mist of diluted neutral detergent.
Paste while removing air using a special Guide.
In the end, when I tried to paste it after moistening it with a misting spray, the sticking was weak. Is this Large sturdy? The work was completed with the thought.
After drying thoroughly, it was peeled off and gone after a few miles of driving.
Next, purchase Rim stripeM6Tricolor.
Paste in the same work process.
However, as before Spray with a mild detergent solution. The sticking was weak at the "1" point, and I thought it might come off again, so I dried and aired it out with Dryer to complete the work.
As a result, it was still peeling and pelePera, although it did not disappear after a few kilometers.
I bought the light gray this time for the third time.
This time, we dared to paste directly after perfect degreasing without using a neutral detergent solution.
As a result, there is no sign of peeling.
Finally, I can run with peace of mind.
Has the quality of the glue gone down?
Is there a problem with Wheel in gsx?
I don't know. I don't know. Neutral detergent solution." will not be used from now on.
View detail
Reupholstered MDF Rim stripe
I replaced it with Titanium, my personal favorite Rim sticker.
The original wheel has a Vinyl type rim sticker, and it can be removed by using Remover.
It took some time to peel off and wipe up to remove the glue, but all the areas were reupholstered.
As with the last GSR400, I still love the look!
I would like to replace the wheel in the near future because the current wheel has some rust in it.
In the meantime, if you like the way it looks, you will want to ride a motorcycle! We believe that this is directly related to the following
I am personally satisfied.
View detail
It corrects, although it described that the wrinkle was in play contained last time. When 24 hours or more passed, the wrinkle had disappeared. It is in play at the time of 12-hour progress last time.
It corrects, although it described that the wrinkle was in play contained last time.
When 24 hours or more passed, the wrinkle had disappeared.
It is in play at the time of 12-hour progress last time.
View detail
It was simultaneous purchase with an MDF rim stripe. If this gauge is used, it can stick really simply and finely. I thought that what is necessary was just to use a rim stripe and a set since it is not high.
It was simultaneous purchase with an MDF rim stripe.
If this gauge is used, it can stick really simply and finely.
I thought that what is necessary was just to use a rim stripe and a set since it is not high.
View detail
In the silver color, since a tire size was also small and the wheel lacked in force, it equipped. The difficulty of the wearing [ itself ] was OK with the feeling which sticks a sticker highly. Since the decal itself has thickness, there are also
In the silver color, since a tire size was also small and the wheel lacked in force, it equipped.
The difficulty of the wearing [ itself ] was OK with the feeling which sticks a sticker highly.
Since the decal itself has thickness, there are also few fears of air bubbles and a wrinkle entering, and if even an attachment location takes care, it can complete finely.
If a front wheel is equipped, does it become a style with a piece?
Although the engine performance of a motorcycle is not raised, I think that it is a high product of the dress-up effect up.
View detail
It purchased for appearance. A result is large satisfaction. Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not un
It purchased for appearance.
A result is large satisfaction.
Since he liked black and blue, the thing of the blue character was chosen as the black material, but since the area of a black material occupied mostly, it was thought that it was not unexpectedly conspicuous.
(Natural although there are differences of enough if compared with normal ..) Although it thinks that the angle which takes a photograph is also a problem, the impression which is seen rapidly and received is the touch which says that the edge of the tire spread inside.
If appearance was thought more as important, possibly the monochromatic blue product should have been chosen.
Anyway, since it is satisfied with the product itself, I purchase and think that it was good.
However, since this stripe has become comparatively for 4 minutes, the point worried one sticks it, as the portion of a joint overlaps for a while.
(It seems that it is the measure which considered the hit in case of the size of exactly since it is hard to stick by it) If it sticks in the pile and the crevice between joint parts is not processed exactly, garbage will enter from the crevice and it will become a cause of peeling.
Those who are worried will think whether it is satisfactory, if the portion of a joint is cut.
Since I was troublesome, I stuck in piles as it is as the description.
If this point and an edge are separating, I think that it will cut then.
View detail
AGUSTA
I have been satisfied with the product for quite some time now with no peeling. View detail
It goes up nicely.
It would be easier and easier to put it on if you had STAND! View detail
The colors are perfect!
CROSSCUB110 purchased at Webig
I have installed external Wide Rim.
Anodized areas are peeling off due to age and deterioration.
It was a conspicuous and poor Image.
Buy Off rim stripe to recaBarry it
Pumpkin yellow is a good match for OEM colors.
The BlackBase Logo is perfect as an Accent.
The footwear is tight and satisfying.
Rear was Rim width Exactly, but Front was a little too much…
The Tape was very flexible, and I finished it in the form of an ingenious foldover, which was not so bad.
It is strung up in a way that retains Rim's Manufacturer logo, and it is very well received by those around it.
View detail
Fits: YAMAHA YZF-R1, YAMAHA YZF-R6
Buy Repeat... a little too close to home.
Pre-road and each damping force can be quickly adjusted while riding.
It is convenient to turn it with your finger instead of taking out the Wrench or Driver and adjusting it, and it is also very easy to use.
It is also beautiful in appearance. I think it is a little more fashionable.
Installation is very easy. Simply attach it to the head of the front fork and tighten it lightly with two screws.
Small hexagonal Screws and Material:The aluminum adjuster will quickly lubricate the screws if you don't go easy on it.
If you are considering installing this unit, please check the Fork setting to see if the pre-road and damping are in the same position, and if they are in the same position, please check the Fork setting to see if the damping is in the same position.
Or the damping force cannot be adjusted if the damping is lower, if the CenterMinus section is the same or concave.
It also pops out quite loudly. If there is any wiring around the installation area, it will get tangled.
View detail