Reviews
I still need … Smartphone Navigation!
What made you decide to buy?
Before I installed the KawasakiOEMOption Steering Damper on my ZX-6R, I had installed a KIJIMA Handlebar Mount Bracket, but it interfered with the Steering Damper. After considering alternatives to KIJIMA's Mount Bracket, we decided to use KIJIMA's Mount Bracket. WorldWalk:Smartphone Mount bar I met and purchased the product.
How was your experience with it?
Before purchasing, I was disappointed that there was not enough information about the WorldWalk:Smartphone Mount Bar for 6R. I have been using it to hold my cell phone for a long time. I used to use "Oxford:I installed the "Clicker /Handlebar Mounting for Motorcycle" and it is firmly in place and does not interfere with anything else. The OEMMeter is also clearly visible, although the phone can only be mounted sideways.
Unlike KIJIMA's Handlebar Mount Bracket, this bracket is mounted in the upward direction. I was impressed by the manufacturer's skill in measuring the mounting position to maintain a subtle clearance, but there were some disappointing points. The paint job of the bar clamp is perfect, but the finish of the HolderBody is a little bit rough. I thought that it was probably manufactured by a certain Large land … manufacturer. (As a personal opinion)
Regarding installation …]
Remove the OEMHandlebar clampBolt. Once removed, use the supplied aluminum collars to attach the bracket for fixing the holder. This is where the ad-vise comes in. The included M8 bolt is used to secure the bracket and aluminum collar, but if the bolt is tightened at the specified torque, the bracket will move to the tightening side, which will affect later work. First of all, set the quantity:Pair (for Left and Right) The Bracket for fixing the Holder on the left side is temporarily fixed. Next, temporarily fix the Holder to the Bracket for fixing the Holder and attach the bar. (At this time, there are two washers for the Holder. Since the clearance is delicate, do not use washers for temporary fixation, but use Bolt only for temporary fixation.) where the bar Quantity:Pair (for Left and Right) position adjustment and fix the bar firmly to the Holder. (The bar has a hole for drainage! I am at this time using theQuantity:Pair (for Left and Right) and adjusted the bar so that the hole for drainage faces down). After adjusting the position of the Holder and bar, we left them as they were, and set the Quantity:Pair (for Left and Right) Tighten the holder fixing bracket of the "2" at the specified torque. Finally, use the two washers that were removed from the bracket for fixing the holder at the position specified in the Instruction Manual, and tighten the holder with the specified torque. This work was a little difficult because there was not enough information about the WorldWalk:Smartphone Mount bar for 6R in advance, but the work was completed without any trouble. WorldWalk:Smartphone Mount bar is recommended.
View detail
Parts missing
I went to the local post office yesterday to pick it up after work, brought it home and opened it.
The fins on the Fog Lamp were missing.
View detail
Really grippy
Really grippy, time will tell how durable they are but I'm thinking they will last a long time. Definitely the best tank grips I've found for my bike. View detail
Fits: YAMAHA BirdCity, YAMAHA BirdCity 155, YAMAHA Tricity155
Not compatible with Givi.
It is good because it is normally usable, normally durable, and less expensive than famous Manufacturers.
But one drawback, or something to watch out for, is that
They are not compatible with Givi.
Givi and Kaeppa also have interchangeable mounting bases, so you can change only the box to suit your touring needs.
When I attach a WorldWalk box to a Givi base, it fits, but the bracket that holds it in place does not fit properly, and I can't get it to stay in place.
When I set the Mounting Base to WorldWalk, Givi's was still not working.
Then, remove the SpacerRubber from the base, attach the box, drill a hole from the bottom, and pass the bracket for the corrugated plate through it.
Just close it with Screw when you use it, and you are done. It should not come off easily.
View detail
Very convenient, but also requires caution
With the Motorcycle Mover, I can easily pull my 250kg lighter machine up against the garage wall. I don't have to push and pull the machine over and over again, which saves me a lot of time and effort.
The product is well built, rigid, and beautifully finished with a high quality feel.
However, there are some points to note.
The Motorcycle stand may be paid off while the Motorcycle is being moved in conjunction with Stand Mover.
Relying too much on Stand Mover can be dangerous, and I almost knocked over a Motorcycle once.
This can be prevented by installing the Stand Mover with awareness of its orientation and moving the Motorcycle slightly upright.
Because we are moving heavy objects, there is a certain amount of danger involved. We always try to handle them with care.
View detail
Fits: YAMAHA Bolt, YAMAHA Bolt, YAMAHA Bolt CSpecifications, YAMAHA SCR950
Good sense of unity with dedicated mounting Stay.
The product arrived and was installed immediately.
I was informed that it interferes with Headlight, but it seems to be on the borderline between interference and Fit.
It appears to be installed in a way that overlaps the Headlight Ring information.
I attached the Sponge tape to the inside of the Screen at the interference area.
The previous model was a Universal Product of the same manufacturer, but this time it is an Exclusive Design Stay, so I think it fits the car better than the previous model.
When I straddle my car, I can see the inner Sponge, but that's okay.
I like it, although I haven't actually driven it yet.
View detail
You should buy a DAYTONA conversion Spacer.
I think the outer circumference is Cut-out accurate.
However, the edge surface is gouged and anodized without Edge treatment, so it is dirty.
Also, the holes for the fixed bolt are off-center and do not make a nice circle when combined.
In addition, since a thin Screw is cut directly into the aluminum, it will almost certainly lick if you try to tighten it to the point where it will not rotate.
I would much rather buy a Daytona Φ13Pipe conversion ClampSpacer (https://www.webike.net/sd/23697712/) than buy this. This is just an expensive Garbage. The proper price would be about 1500 yen.
View detail
It's expensive, but nothing else will change that.
The price is quite distressing before purchasing, but if it can be moved freely, it will be easy to move in and out of Garage, and even increasing the number of cars is not a dream.
With this New Model, both the front and rear wheels can be moved, allowing for effective use of space.
I saw some reviews on the old one that it still had the Edge, but I guess it's good that it's made in Taiwan? There is no Edge and there seems to be no worry about scratching Boots.
I'm not sure about Merit, which increased the number of Bearings on Motorcycle Mover to three, because it allows you to move without grounding the Bearing under your feet when pushing and pulling. I think it is suitable for those who want to stabilize the bike and step on it as hard as possible, but for me, it is useless because it increases the resistance to ground contact.
I tried to move GSX1100SKATANA which is the heaviest body to move The Motorcycle Mover did not flex, and I could feel a sense of its solid strength, which was reassuring.
Subtle is the Stand Mover.
When using the Motorcycle Mover, the front or rear wheel is used as a branch in a circular arc, so the bearing of the Stand Mover is designed to roll in a slight arc.
It is good if you work from the Side Stand side, because you can push and pull it while checking, but from the Right Side where you can't see the Side Stand, you can't slide off the Stand. I am afraid that it will come off and I will fall off.
As a countermeasure, since the board is reasonably thick, I am thinking of making a tap, making a rip with AluminumAngle, and attaching it with Butterfly Screw. If you want the best, it would be better to laser-cut the plate into the shape of STAND and sew it (you need to know an ironworker who has a laser cutting machine to do this...).
A clean floor surface is a prerequisite for installing Motorcycle Mover. My garage is an office that originally had Linoleum flooring, so the concrete is rough and the rolling resistance is large. (I feel like putting a steel plate on it.)
I would like to ask WorldWalk to sell the Stand MoverSingle Body, because to pack the Motorcycle, you have to push it towards the Left Side, but it is difficult to retrieve the Stand Mover. I hope you can make this happen soon because I would like to have two more cars.
View detail
Satisfied
I bought it because I moved to a new house and my parking space was getting smaller. I use it on my ZEPHYR750. I use it on my ZEPHYR750 and recommend it to short women who are not strong to practice many times to get the hang of it. View detail
Fits: YAMAHA BirdCity, YAMAHA Tricity155, YAMAHA BirdCity 155
More effective in improving fuel economy than increasing maximum speed
As I mentioned in the Title, the good thing about this product is its contribution to fuel economy.
The wind protection effect was not as great as we had imagined, but fuel efficiency was clearly improved.
It may depend on the road conditions and personal driving style, but in my case, I used to drive 33-35km/L in NORMAL mode, but now I average over 40km/L. 。 (*Touring)
It may be a small thing, but it's very good.
The other bonus is that if you put your phone under the Screen, it is hardly affected by rain unless the wind is very strong sideways, which was a pleasant miscalculation.
View detail
thank you for good product
It is a thick and long bar that compensates for the shortcomings of the existing bar, so it is good to safely mount a phone holder or other products. It is a thick and long bar that compensates for the shortcomings of the existing bar, so it is good to safely mount a phone holder or other products. do View detail
For Scooter Smartphone Holder
[How is it used?
I use my Scooter for commuting to work, and when I go to a different place, I thought it would be convenient to have a smartphone navigation system, so I was looking for a variety of attachments, etc. I found this product, which seemed cheap and easy to install, and bought it.
It is for PCX160, but I think it is possible to install a large body if it is a Scooter, such as a type that is co-tightened to Mirror.
Was the one you received as per Image?
The quality of the product itself is commensurate with the price.
How was your experience with it?
The screws on the Clamp that hold the Mount Bracket and bar together often loosen, so I think it would be more stable if they were tightened with a very high torque.
Then, I had to change the angle several times until I got it to the best position on my phone. It took time to find the right angle.
View detail
Z900RS Side Back Support
It is easy to install
The size of the Side Back was good and functioned well.
View detail
Fits: KAWASAKI VERSYS 1000, KAWASAKI VERSYS 1000
Firmly.
14mWrench for Mirror removal is a quantity.:I was unprepared for the 2pcs, but the work itself was easy, and the Smartphone Holder and Camera were also fixed perfectly. View detail
A little hang is required, but …
It's an Exclusive Design, and it looks very nice.
As for the effect, the wind hitting my chest is much lessened, especially when driving at high speed.
The installation requires a bit of a hang, as the Bracket is installed in a very intricate location. Also, you need to have some tools.
The included Instruction Manual was easy to understand with pictures.
View detail
No need to feel uncomfortable.
It's good enough that you can't tell if you're wearing it or not.
Good in design without compromise
View detail
It was windproof.
It was well windproofed.
Depending on where you put it, it will work from the neck down.
View detail
Fog Lamp installed!
I installed the Fog Lamp. It looks like a BMW! (Lol) 。
I don't drive at night very often, but I feel safe. I don't think I will go to the forest road at night.
The installation required a bit of modification because it was installed in the Endurance Power Supply Kit. In the instruction manual, the power supply should be directly connected to the battery, but since I installed it in the Power Supply Kit, I cut the power supply with Electric Works Pliers and installed the Bullet Type Terminal. I soldered it on just in case. I plugged the terminal into the Power Supply Kit, and since there is a switch wiring, I plugged it into a 10A fuse box according to the instruction manual.
It took a little time because it was the first time for me to do all these things, but the installation was done!
And the brightness is perfect!
View detail
Windscreen installed!
I installed a Screen to block the wind. The head part of the helmet is better than nothing. It's better than nothing, and there is also a Demerit. I also thought it might be dangerous if I fell down on a forest road. So, I think it's good for people who ride in town or at high speed. I think it's good for people who ride in town or at high speed, but honestly, I don't think it's necessary for people who only ride on forest roads.
The installation is surprisingly easy.
View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE KRT, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R
Durability is unknown
Tank side, Cowl, Tank Pad and Quantity for just over 5000 yen:1 Set of 5pcs. is a good deal.
The material is said to be medium-hard EPDM rubber, but the texture is Sponge rubber or Neoprene, like Racer's Sponge sheet.
It is soft and feels good and Grip is good, but it is too soft and I am worried about its durability.
If you have any questions, please contact us. I'm sure it's large and strong.
Cut's measurements were pretty accurate and easy to apply.
The softness will help reduce fatigue during long touring.
It is 3mm thick and has a Sponge-like cross section, so I don't think it looks very good.
View detail