Reviews
Well, the Gold amount is acceptable.
Conversion Connector for Bosch wide watt blinker relay.
Convert 4 wires on the body side to Relay 3 wires.
My Motorcycle, a CBR650F, has 4 wires on the body side, so I needed this product to install a wide watt blinker relay.
The coupler shape is 4-wire, but as you can see inside, the wire itself is 3-wire (because the Relay is 3-wire). (Relay is 3-wire).
Therefore, Hazard will not be available when the key is Off.
The ICRelay fits in the place where the regular Relay fits, but since this product must be used in a way that it pops out from there, a great deal of ingenuity is required in the way it is delivered.
Gold price is a little over 500 yen, which is quite inexpensive considering the cost of the product. (It is common for this type of product to cost 1,500 yen just to connect the wiring and resistor, so this is cheap enough for a couplet-on).
View detail
Couplet-on for easy installation
Used on the last model of CB400SUPER BOLDOR.
The bulb Blinker was replaced with an LED Blinker as well.
The Relay position is under the Tank, so sound is not a concern.
Instead, the replacement process was Large strange.
Not directly related to Relay, but I want it to last as long as possible.
Wiring was too long to fit, so it was bent sideways and pushed in.
The OEM WaterproofRubber cover will be facing up or sideways so water can get in. This makes it a *−1.
It would be better if there is an OEM Type without Wiring.
In general, it is a good product.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
To relocate Blinker
[How is it used?
NSR250R (MC21) I bought Rear Fender to fix UniversalBlinker because it was Cut.
I could have made my own bracket, but I could only see a future where the quality would be disappointing for the trouble involved, so I used this one.
Was the one you received as per Image?
It is just a Plate, but the strength and quality of the paint were perfect.
Was the installation difficult?
If used normally, it only takes a moment to insert it between the License Plate and the Rear Fender.
However, in my case, I used an M10Bolt type blinker, so I had to extend the hole and make a clearance for the blinker wiring.
How was your experience with it?
We were pleased to be able to install the Blinker in the exact position we wanted.
I did not look at the size of the blinker I had on hand, and when I expanded the hole, it was scratched quite a bit, but I'm sure the license plate will make it invisible, so I'll pretend I didn't see it.
[Included Parts:were they on?
This product only.
Since the Bolt for License Plate may be Limit, it would be good to have a longer Bolt separately.
[Was there anything that disappointed you?
I felt it was slightly higher than other Manufacturer's products.
I am satisfied with Quality.
【Review】
The Blinker position can be easily relocated to the side of the License Plate.
There are several manufacturers offering similar products, but I chose this one because I couldn't find anything that fit the size and because it was in stock.
View detail
Fits: SUZUKI glass tracker, SUZUKI glass tracker
(very) satisfied
Lens is painted in yellow color, but the brightness is neither good nor bad! View detail
Good response
The product arrived exactly as I had imagined. The only problem was that there was a slight defect, but I was thankful for the quick response after that. I would like to thank you again for your prompt response. View detail
SR400 Tail with a modern look
The LED's characteristic sparkling light will also increase visibility. View detail
Fits: MOTOGUZZI CALIFORNIA, APRILIA Scarabeo250, APRILIA Scarabeo200, APRILIA PEGASO650 STRADA, HARLEY-DAVIDSON VRSCD V-ROD NIGHTROD, SUZUKI Across, SUZUKI SV400, SUZUKI RGV250 (Gamma), SUZUKI RF400, SUZUKI GSX400, SUZUKI GSX-R1100, SUZUKI DF200, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA XZ550, YAMAHA XZ400, YAMAHA XJ750, YAMAHA XJ750, YAMAHA XJ600, YAMAHA XJ600
Vehicle Inspection Measures
NORMAL H4 will pass vehicle inspections, but for further peace of mind, 60W is labeled as equivalent to 100W.
Highly efficient Type was selected.
I measured the illuminance with a smartphone app and saw that it was up about 20%.
However, the H4 was used for years before replacement, and even if it is NORMAL, replacing it with a new one will pay for itself.
I also think it will increase illumination.
Because of its high efficiency, we are concerned about its durability and would like to evaluate it in the future.
View detail
Large change was saved by the SPIDI-like response.
I found this product on this site when my touring date was approaching. I am very pleased with the immediate delivery and the large size.
At first, we tried to place an order for the manufacturer's product through a motorcycle shop, but we were told that we would have to check the inventory and place the order at the end of the week.... I got only a carefree response like, "We'll check the stock and place the order in the week after tomorrow....
I am appalled at the totally outdated response.
This time I was satisfied with the Large change to this Site's Service.
View detail
For Custom
I bought this for Custom for Grom.
I thought about LEDs, but Wiring and other
I thought about the hassle w this one for the time being.
I am satisfied with the product.
This time, we purchased the front and back together.
View detail
If you want to replace Valve, this is the one!
RC390 (2021 model year) The OEM Halogen Headlight was too dark, so we replaced it with this LED Headlight Bulb.
The quality and texture of the product is perfect.
The process is similar to a typical Valve replacement, such as removing the OEM Valve from the Coupler, removing the ValveBody and assembling it in the reverse order as when the new Valve for the LED was removed, and putting together the Wiring.
However, there is a gray cap on the reverse side of the headlight of the 2021 RC390, which may slightly interfere with the aluminum heat sink. Therefore, we installed the headlight by rotating the LED bulb first and then pushing the cap in, while sticking the cap halfway in.
When I purchased this product, I was not sure if I could afford this price for two Valves since the 2021 RC390 has two lights.... But when I installed it, I was very impressed with the brightness.
Both Hi and Lo can be installed with the same work and no modification, and the brightness of the product is highly satisfactory with no complaints.
View detail
BEETBlack tail
[Color] I purchased a BEET Tail lamp cover for my SmokeTail. I hope it is still cheap because RS is a popular car model. View detail
Fog Lamp installation.
I installed it to supplement the Headlight. This is a Large Variant value for money product. It is bright and reliable. I am very satisfied with the product and the workmanship. View detail
Fog Lamp installation.
I installed a Fog Lamp on my CT110 HUNTER CUB to help with the lack of Yellow dragons in the headlight. This is a great deal for the Large size. It's great! It was good for safe driving and peace of mind. I am glad that I found the installation manual. View detail
Fits: HARLEY-DAVIDSON sportster, HARLEY-DAVIDSON softail, HARLEY-DAVIDSON Dyna., HARLEY-DAVIDSON FLSTF Fatboy, HARLEY-DAVIDSON FLSTFB Fat Boy Low, HARLEY-DAVIDSON FXCWC Rocker C, HARLEY-DAVIDSON FXD Super Glide, HARLEY-DAVIDSON FXDB Street Bob, HARLEY-DAVIDSON FXDC Super Glide Custom, HARLEY-DAVIDSON FXDF Fat Bob, HARLEY-DAVIDSON FXDL Low Rider, HARLEY-DAVIDSON FXDWG Wide Glide, HARLEY-DAVIDSON FXST Softail Standard, HARLEY-DAVIDSON FXSTC Softail Custom, HARLEY-DAVIDSON XL1200C 1200 Custom, HARLEY-DAVIDSON XL1200CA 1200CA Limited, HARLEY-DAVIDSON XL1200CB 1200CB Limited, HARLEY-DAVIDSON XL1200CX Roadster, HARLEY-DAVIDSON XL1200T Super Low 1200T, HARLEY-DAVIDSON XL1200V Seventy-Two
Compact and GOOD
With OEM, it's not so bad hanging from Handlebar, but I'm getting tired of it, so I changed Blinker.
Front is this product and Rear is Active's NumberBlinker.
The work is just to cut off the Wiring and connect it.
First, Rear was assembled and test lighted. Normal. Ceramic resistor was installed.
Front is co-tightened to Mirror, and a resistor is engaged to test the light. Hazard lights up no matter how many times I try.
The resistor was removed and reassembled.
I don't know, but okay.
The brightness is sufficient, so I would like to think it will pass inspection.
Of course, it comes with EMark, so it should work.
View detail
m10x1.25のネジナットに使用しています。用途に応じて色々な用途に使えます。丈夫です。 View detail
From Chinese HID to Sphere LightRIZING2
Used for low beam of TDM900.
Additional Spacer 1980 yen is required for installation. (I could have made it myself)
Since the rubber packing in Included Parts:does not fit, the coupler will not fit unless the original rubber cover is cut.
When we got the vehicle, it already had 35W Chinese HIDs, so this is not a comparison with NORMALHalogen.
Even though it is a Chinese HID, it is 35W, so it was quite bright, so even after replacing it with RIZING2 LEDs, it seems a little dark.
The color temperature is higher than that of HIDs, or perhaps the color is comparatively blue.
I would have preferred 4500K.
However, I am glad to know that the symptoms such as the engine igniting when the high beam is turned on while the low beam of HID is turned on, as if the voltage had not caught up with the low beam, the light disappears for a moment, and the engine ignites, are gone.
View detail
Fits: HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CB1100, HONDA CB1100 EX
Self-sufficientParts
[How is it used?
Installed on CB1100. The self-satisfied parts.
Was the one you received as per Image?
I asked for Gold, but at first
I was like, "What? Did I get the wrong Silver?" No sense of Gold to the extent of
But when installed, it is not too buried in the surroundings, nor is it too conspicuous,
It's also nice and assertive in moderation.
Was the installation difficult?
Hexagonal Wrench is 10 minutes away.
Instruction Manual is also very detailed.
How was your experience with it?
I think it's cool.
I think it could have been Silver.
View detail
Fits: KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1200 Daeg
PoshLED sequential
Installation of the product was easy, even for an amateur.
It was very bright.
View detail
Fits: YAMAHA bolt, YAMAHA bolt, YAMAHA bolt, YAMAHA SCR950, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA Bolt CSpecifications, YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A, YAMAHA XVS950A
Fits BOLT Shoulder Bag-2013
Arrived earlier than expected. There were no problems with the product.
I didn't like Silver (Rust generated) and wanted it to be Black anyway.
Although not cosmetically superior, the imported product was selected because it was cheaper.
View detail
Used for Super Cub custom
I made the right decision to purchase the ClassicalSeries as it is used for the SUPER CUB and I am using it with the LED Specification. View detail