Reviews
Fits: MV AGUSTA F4 RR, MV AGUSTA F4 RC, MV AGUSTA F4 R, MV AGUSTA F4
Ah
Bolt is short, so I diverted OEM, but it's going round and round, and I don't know if that's right or wrong. View detail
Axle Slider
Easy installation, just insert and tighten up, but the instructions are not good and some washers need to be added to tighten up. Looks good. View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R, HONDA CBR1000RR-R SP
Bolt does not fit
Bolt is too long and cannot be fixed. I added two additional Washers to accommodate this. View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10R SE, KAWASAKI ZX-10RR
10R SE Swing Arm Cover
I drilled a hole in the carbon cover to install it because it interferes with the chain guard, and the double-sided tape is not strong enough. View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI KATANA
Rear one place was loose.
Rear parts were loose. The rear parts were loose, so they were adjusted by Seam. View detail
Not what I was expecting lol.
I bought the Logo from RyTEC because I thought it was stylish, but I didn't think PadBody would be. [Color] I didn't think it was Clear.
If you put it on a black tank, you can't even see the logo.
If you accidentally touch the back side, fingerprints will be left behind and you won't be able to remove them.
View detail
Bolt kit for frame
Buy Bolt kit for Frame There is no instruction manual, and it is not listed on Net, so I don't know where to install it? View detail
If you look closely, you'll see a lot of Wound.
I purchased the glossy Carbon.
The shape was fine, but there were many disappointments such as WOUND on the surface, dirt and unevenness.
It is not noticeable, but it is still bothersome when viewed up close.
I don't think I will buy Carbon stuff from this Manufacturer next time.
I am not satisfied, but okay.
View detail
Screw holes are too small!
The tooling will be Hexa.
But the Screw hole? The hole to insert Hexa is too small.
Anodized will scrape off and ground out when installed normally.
I think the quality is poor for the pricing there.
Quantity when installed and just recently removed and installed.:2pc. Set head almost licked it.
We will be reverting back to OEMBolt soon.
View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R SP, HONDA CBR1000RR-R
Included Parts:Bolt is useless
The Bolt was a poorly made item that did not fit the dimensions.
Too long and too thin. The front cowl does not become stable at all when it is installed.
If you use it, SPE106NER/ROS of the same manufacturer is recommended.
View detail
The installation method is unique
The GSX-R1000R does not have an inner fender on the Swing Arm I chose this product
Compared to similar products from other companies, this is a small swing, and the casting hole of Swing Arm (?) I think it's impossible to make it any bigger than this because it's a two-piece rivet fixture It is But the price is a Large swing (Bitter smile) 。
Maybe it's the way it's installed, but the Rivet sometimes comes loose In my case, one of the rivets fell off after about 2000km It needs to be checked occasionally
It was Ideas that made it possible to install SMART without using Tie Band etc Practicality..
View detail
I don't recommend it
The material is super Duralumin, so it's pretty strong there Also, I think Anodized is a strong one
However, there is no Construction Manual and there is no guidance on the Site, so where is it? It's hard to know if you're going to install it
Also, the Quick fastener was not included, even though it's for Fairing
View detail
I don't recommend it
I think Anodized is a good color and a strong one
However, since there is no Construction Manual and the Site doesn't show it I don't know where the Bolt is more than for Fairing!
View detail