Reviews
Easy to secure power supply
It is an excellent and easy way to secure power. View detail
They say it's good if it lasts 5 years.
After five years, it broke. When I removed it, the yellow-colored luminous body was shattered and the base was burnt to brown. The light suddenly faded and became like a miniature light bulb and disappeared. I was surprised because I happened to be watching it. It would have been extremely scary if I had been driving at night.
When I bought it, the yellow colored tip was not square and the corners looked peeled off in places. I asked the ManufacturerStaff if the Large tip was sturdy, but they said it was fine, so I had it installed.
Well, it would be impossible because it looks like the LED light-emitting base part is burnt out.
As for the product review, at 6000k.
It is not brighter than OEM, but the color is White, so some scenes actually look darker. It is still not as good as the most powerful HeadlightHID, but it looks better than the OEM Halogen when compared to rural roads and other places without streetlights. 。
However, in urban, city, suburban, and highway areas where there are some lights, the white LEDs are covered by the lights and it is difficult to tell whether the light is illuminating or not.
If the Type is one light on low and two lights on high, I would recommend changing the color temperature with low high.
This time I did the work myself, but when I first bought it, I was told that it would wait 20,000 hours or 10 years if it didn't break, but in fact it was 5 years, so I felt like I lost money, but that seems to be the way it is.
It is good that they are cheaper now because of the New Model, but I wish they would have stopped reducing the warranty to 2 years if they continue to claim that they can be used for a long time.
Now, how to do the work
This time, I performed the work myself, copying the way SphereLight's ManufacturerStaff actually did it on my Motorcycle.
As mentioned in the postscript, the way this Rubber fits (How to put it out?) If this is the case, the heat sink portion will be buried in the rubber, so I am concerned about whether the heat dissipation will be large enough to withstand the heat.
Turn the round cover of the OEM Headlight unit counterclockwise about 1 cm to remove it.
Remove the valve spring and remove the light valve.
Remove the Attachment from the Valve of the product and insert the removed Attachment into the place where the Headlight Bulb was inserted, with the four notches facing backward, and fasten it with the Spring.
At this point, you should install the Valve once in the Attachment and remember the feeling of pushing and turning it to install.
Attach the supplied CouplerConnector to the product as described in B of the Instruction Manual.
Connectors on the body side and the Light side are connected.
...At this point, conduct a lighting test.
The space inside the Headlight unit is quite large when you put your finger inside, so leave about 15cm of Wiring and put all Connectors and Controllers inside the Unit. (I put almost all of them in Space under Unit)
Note that if the wiring connected to the light is about 10 cm, the light valve will stick when the cover is attached and will not be able to be pierced.
If the controller rattles inside the headlight unit, use the Tie Band to hold the controller in place. I don't do it.
Once this is done, it is time to install the rubber cover, which is the most difficult part.
It takes several hours at worst, and although it is easy to install if the Rubber is heated considerably, it is not recommended because deformation is a concern.
The difficulty level increases because everything is put into the Unit.
Push the outer frame of the Rubber cover into the Unit.
At that time, the side that is folded should be toward the rear of the vehicle.
When you push it in, there are three indentations where the OEM's round cover fits.
Make sure three Folds are outside the Unit, then install the LED Bulb.
(Note that if you push the Rubber as hard as you can, only one Fold will come out backward.)
(The outer frame of the rubber cover of the type after the warranty period of 2 years is larger than that of the type before that, so it should be installed in a larger size.)
LED Bulb is perpendicular to the ground when installed.:Pair (for Left and Right) to be facing the
If the remaining wiring seems long, push it in a little at a time.
The above work was completed without making any cuts.
ManufacturerStaff had done this and it was a work procedure that worked fine.
However, if the rubber is pushed out this far, the heat sink will be buried in the rubber, so I wonder if the heat dissipation is Large sturdy. I wonder,
I had done it this way before, so I copied it as it was.
View detail
Lack of good product Level is low.
Used on a SEA BASS VST 650. I tried riding at night with it on, but it was dark. It is just too dark. Also, the optical axis is a little bit off. So, when I adjust it to the lower side, the difference of optical axis between high beam and low beam is very different. PIAA or Ray Brick (Stanley) I would not recommend purchasing anything other than the 2-wheel dedicated LEDs from I think the next best choice would be SYGN HOUSE. By the way, I have purchased SYGN HOUSE twice in the past, but the low beam ran out after about 1.5 years. I hope this will help you in your purchase. View detail
Fits: HONDA CB300R, HONDA CB125R, HONDA CB250R
It's difficult, isn't it?
I put Meter's Film on the new car.
I thought it was no different than GlassFilm for cars.
He applied it with a mild detergent.
Eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee dust ・・・・ tears
That's a tough one.
I wouldn't worry too much about it since it's for Meter Protection purposes.
Fortunately, it is expensive and contains two different types of films.
I'll try again next time.
You must be a PRO to be able to do this so beautifully.
View detail
It picks up Noise.
I thought I knew what ShiftTiming was even without the Tachometer.
The re-acceleration is inevitably slow in the SCENE that requires climbing the board.
I purchased it to keep track of RPMs.
While retrofitted, the position and Size are moderate, and the high brightness makes it easier to read than the OEM Speedometer.
However, the Clutch Cable runs through the Shift Up Indicator position, so it is not visible when the driver is riding. (I guess it depends on your body shape …)
Also, as is common with retrofitted tachometers, the rpm may rise or fall by around 500 rpm during cruising.
The performance is sufficient for me as I only needed to know the approximate number of revolutions.
I was able to correct my riding style because I was SHIFT UP at lower rpm than I expected.
The installation is more difficult because the tank needs to be lowered.
The illustrated Instruction Manual is clear and helpful and manageable.
However, although not a problem with this product, we had two problems during installation.
1. OEM Speedometer BracketMounting Bolt stuck at an angle.
It is fixed by biting into the Blinker Bracket and Meter Bracket.
The Bolt on the Meter Bracket was stuck at an angle, making it difficult to replace the Bolt.
(It's mainly Honda's fault since it's due to individual differences in the car body.)
2. occupies the power supply for Attachment (+ voltage shortage may occur)
The power supply for the Attachment provided on the Brake Side is used.
Already incompatible with USB power supply and Cigar socket.
The same thing happens when I make the connections as per the Instruction Manual, but
While the Cell is spinning, it seems to run out of voltage and reboots (re-opens).
The Harness length is long enough to reach the bottom of the Seat even through the bottom of the Tank.
I modified the Wiring to take power directly from Battery and it improved.
The voltage display function compares the voltage at the time of wiring according to the Instruction Manual with the voltage at the buffer.
The voltage seems to be slightly lower in the former. (It is not the fault of this product, but the spec. on the car body side.)
The following products were used for the Wiring change.
KIJIMA:ACC Branch Harness Kit]
https://www.webike.net/sd/21317023/
DAYTONA:Attachment Power Supply Unit D-UNITPlus]
https://www.webike.net/sd/24232600/
View detail
Fits: SUZUKI GSX750, SUZUKI GSX750 , SUZUKI GSX750 , SUZUKI GSX1000S, SUZUKI GSX1100S, SUZUKI GSX1000S, SUZUKI GSX1100S
KATANA SPEEDO NEEDLES
I recieved the Katana speedo needles quicker than expected and it arrived in a well protected package. Once I get some free time I will install them. I was so impressed with the service that I did not hesitate to order another product. Thanks! JOHNNY "B" KATANA View detail
I don't know if it will fit, but I bought it anyway.
I don't know if it will fit, but I bought it anyway. View detail
Nice touch!
The Tail is much brighter and I am happy with it! View detail
Good visibility!
I installed this together with my Ninja 250SL that I modified for Gymkhana when I converted it to NAKED. The best value License Plate Bracket and Reflector are available in quantity.:I am very happy with the Set. The visibility is very good as it claims to be equipped with many high brightness LEDs. The wiring is also very well made, so it is a recommendation! View detail
Fits: KAWASAKI VERSYS650, KAWASAKI VERSYS1000, KAWASAKI NINJA650R, KAWASAKI NINJA650, KAWASAKI NINJA400R, KAWASAKI NINJA400, KAWASAKI NINJA250R, KAWASAKI NINJA1000, KAWASAKI NINJA ZX-6R(636), KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI Z800, KAWASAKI Z1000, KAWASAKI Z250, KAWASAKI ER-6F, KAWASAKI ER-4N
NINJA400R
RearBlinker lens of NINJA400R was replaced.
[Color] From Clear [Color] Just by being Smoke, the Rear view was tightened up considerably.
View detail
Fits: HONDA CB750, HONDA CB750L (license training vehicle)
To MAGNA50.
Cheap!
Fast arrival!
Good texture!
No complaints!
View detail
Durability may be difficult.
The ease of installation was a plus.
The battery stopped charging less than six months after installation.
According to Manufacturer, it was due to age and not covered by warranty.
I hoped it would be a little sturdier and last longer.
View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA CT125CT110 HUNTER CUB
There's no way out of air.
I did it with a good amount of detergent and plenty of Kiribuki, but I couldn't get the air bubbles out. View detail
the best dress-up item
It's the best dress-up with a long tail. The archi product is too expensive and large, but it shows the right price and size. There are no problems with visibility and brightness. View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
the best dress-up item
It's the best dress-up with a long tail. It's a real old z-series look. You can say I did a long tail because of this. No problems with visibility, brightness, etc. View detail
Somewhat difficult to install
Screws could not pass through and the hole was widened with a 6.5mm Drill for Gold.
Also, USB port and voltmeter are Quantity:The set is great, but you need to cut 5mm off both ends of the middle collar and the bracket to install it on the CRF250 body. The above mentioned work was necessary when assembling the Headlight unit, which is not shown in the YouTube video. The light is very bright and I am satisfied with it.
View detail
DAYTONAusb power supply& voltmeter
Since I ride a Motorcycle with Touring as my main vehicle, a voltmeter is very useful for battery management.
The usb power supply is really useful when touring.
DAYTONA products are reliable and satisfactory.
View detail
Rare Other Brand Product for 6v
This is a Horn for 6V electrical equipment, which is now rare.
Since most of the vehicles have been manufactured for a long time, we recommend replacing them with OEM replacements.
View detail
No problem, no problem, no problem
There is no wobble and no problem. View detail
Classic color and cool!
I installed it on my JA07SUPER CUB and it looks great with the classic color! And the Yellow Bulb is easy to see even in the rain! I like the durability and the fact that it doesn't break easily! I am very pleased with the durability of the bulb and the fact that it doesn't get damaged easily! View detail