Reviews
Fits: SUZUKI V-STROM250, SUZUKI V-STROM250, SUZUKI V-STROM250
Casually Guard
I didn't want to have a LargeGuard, so I purchased this product. View detail
Tracer 9 GT also comes with it.
The Tracer 9 GT was attached without any problem, but please note that the hook to release STAND is near the rear of the footpeg, which makes it much more difficult to release.
However, it is better than nothing, as it provides a much more stable feeling when parking.
View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Stable even with heavy Rear
It is difficult to remove the Bolt and Nut of the OEMSide Stand, but the Bracket itself is easy to install.
The feel after installation is good. The STAND is located at the rear, but it is not difficult to apply.
The stability of the vehicle body with the Side Stand out is unmatched by the OEM.
View detail
Close to HondaOEM Product
I bought this because I fell on the Circuit and my HondaOEM Slider was falling apart.
It also comes with a pin to hold it in place, so you don't have to worry if it gets lost in a fall.
It was also listed on Yahoo!
View detail
Delivery date undecided, huh?
I ordered in August 2023 and was told that delivery was scheduled for mid-February 2024, but I canceled the order at the end of February because it showed "delivery date undecided". It arrived the next day after I placed the order on Amazon.com. View detail
Fits: YAMAHA SR400 19, YAMAHA SR400 19, YAMAHA SR400, YAMAHA SR500, YAMAHA SR400
It is not universal. Use it as needed.
It is a rare Case.
I am not extremely low down, but I have converted the side stand to a short type.
Under certain circumstances.
Why Short Type?
Merit
When parking on a slope or rough terrain.
If the vehicle is parked on a slope, gravel or other rough terrain without the Short Side Stand, depending on the ground conditions, the vehicle may be more likely to rise up and fall over due to strong winds, vibrations, etc. 。
Therefore, by installing the Short Side Stand, stable parking is possible as in NORMAL mode.
● In my experience, prevention of tipping over when horizontal shaking occurs in earthquakes and other events.
Normal stand is almost upright, while Short Type is tilted. (Only when parked on a slight incline or slope.)
What it means.
Upright → less load on the ground.
Tilt→ more load on the ground.
That is
Upright→ Because the vehicle body is close to perpendicular to the ground and lacks stability, it is vulnerable to swaying. If you were pushed while standing straight up, for example, you would wobble, wouldn't you?
The angle between the ground and the body of the car makes it more stable, and the weight of the car on the ground is greater, so it is more resistant to shaking from the rain. The more you lean against a wall, for example, the less likely it is to fall over when pushed, right? It is more effective if you put it in a row.
Demerit on Short Side Stand
If the STAND is not angled, but just short, it will be upright. This is often the case when OEMs cut and fabricate their own products.
The weight of the car body is more heavily loaded on the ground, so if the car body is made of a slender structure, it may be deformed or broken.
I looked for a variety of manufacturers, but decided to go with DAYTONA because of its durability, construction, and price.
good point
○They are no longer toppled by earthquakes or strong winds.
Thankfully, Spring by XXSTAND is also included.
○Because it is originally for lowdown, the rear load becomes large, such as for touring bags, and when the rear is lowered, the parking lot is effectively stabilized.
○Since it is designed to be thicker and shorter than OEM, it can withstand the increased weight of the car when it is parked and tilted.
A bad point
○○ On level ground, the leaning of the vehicle body has the opposite effect. The tipping over Risk also comes out. → The use is quite narrowed down.
Please note that Short Side Stand should not be used under all conditions, but should be considered condition-specific. It should be used in the following situations.
○ Often parked on slopes and rough terrain.
○If you are Lowdown via Suspension or Front fork.
○ When parking, if the Handlebar is about to fall over when it is cut to Right.
And I thought it would be even safer to park with the GEAR in low.
Please consider whether NORMAL or SHORT is better for the terrain of the Space where you will park and the lowdown condition of the car body, and purchase and install it.
View detail
Fits: TRIUMPH Thruxton R, TRIUMPH Bonneville Bobber, TRIUMPH Bonneville Speedmaster, TRIUMPH Street Twin, TRIUMPH Bonneville T120 Black, TRIUMPH Bonneville T120, TRIUMPH Bonneville T100 Black, TRIUMPH Bonneville T100, TRIUMPH Thruxton, TRIUMPH Speed Twin 1200, TRIUMPH Speed Twin 900
Compact.
Installed in my wife's car 。 He has never had to stand up and walk away before, but he said he feels uneasy without it. 。 We selected Engine Guard with a sturdy-looking three-point stopper to support the vehicle body and protect the legs in the event of a fall.
Color in the picture on the Product Page:It looked Gray, but it is actually Black as the description says! 。 It is inconspicuous in the black of the vehicle body, but when you stand astride the Motorcycle, it sticks out just enough to ensure that you can cover your knees, giving you a sense of security. 。 Although quite pricey, the sturdy-looking Pipe is painted Beauty and has a convincing texture.
I had it installed at the shop when I took delivery of my new Motorcycle, because I didn't want to damage it! 。 One of the lower of the two front locations bolted to the car body and the Quantity after the Engine.:Pair (for Left and Right) I am confident that if I had installed it myself, I would have added a Wound somewhere in the one place where the two are connected.
View detail
ChainMaintenance is easy to do.
Installation
・Grease
・Radio pliers
・Driver
It was possible if the
Referring to others, Rubber was added at the end.
Spring was attached by Driver using Lever's principle? Spring was attached by prying with Driver.
It seems unlikely that about Touring would STAND during banking.
View detail
Original suzuki parts
About quality and texture: quite light About the feeling of use: sturdy and fits gixxer 250 Products to buy together: no need Difficulty of installation: very easy Cost performance and comparison with other products: not easy to find bumper/engine guard for gixxer in malaysia About shipping and packaging: very well bubble wrapped Any concerns, cautions, or advice when purchasing: just plug and play View detail
Xsr900 oem frame slider
Item all in perfect condition. View detail
Anyway, I'm not going in.
Quantity:Pair (for Left and Right) Both thought it was SMark, but … it wasn't.
I managed to get it in after considerable pounding with a mallet, but after that, when I moved the Tire, it sounded like it was rubbing somewhere, which was a failure.
It looks like it would be better to have it done properly at Shop.
View detail
I knew I wanted a Center Stand.
As expected, OEM Product View detail
Fits: SUZUKI KATANA, SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000GT
Can also be installed on the GSX-S1000GX.
[How is it used?
It was installed to minimize damage when standing up.
It's a component I don't really want to be a part of.
Was the one you received as per Image?
It was exactly as shown in the image. I had previously installed a Frame direct mount on a different model car, but this time I chose the Plate type because the bolt might bend in the event of a fall.
Was the installation difficult?
I asked Shop to help me with the possibility of the Engine falling off during installation.
How was your experience with it?
I like it because it is not that noticeable.
[Included Parts:were they on?
InstallationInstruction Manual was kindly provided.
[Was there anything that disappointed you?
None
Point and hang of installation
It would be possible for an individual to install it if there is a Jacketc. just in case. It may be a good idea to install one side at a time.
[Opinions and requests to Manufacturer
It seems that all GSX-S1000Series can be installed, so I hope you can add compatible models.
View detail
BABY Face Engine slider CBR600RR
The installation position is Exactly, high quality, and I am satisfied with it. View detail
Fits: DUCATI SCRAMBLER FULL THROTTLE, DUCATI SCRAMBLER CLASSIC, DUCATI SCRAMBLER ICON, DUCATI SCRAMBLER URBAN ENDURO
Easy Stand Hook installation
Stand Hook is very useful for chain maintenance and other work with the rear tire in the air.
This product was easy to install, just tighten with a Hexagonal Wrench, and it worked without any problems.
The product looked great and was satisfactory.
View detail
Fits: BETA RR 2T 250, BETA RR 2T 250 RC, BETA RR 2T 300, BETA RR 2T 300 RC
Cracked.
I just recently purchased it on Outlet.
It cracked after one use. I didn't ride it HARD, just a few times over logs.
Was it cracked or degraded from the start?
I don't know if I'm riding the wrong way, but I think it's moroi.
You should check it carefully when you buy it.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S150, SUZUKI GSX-R150, SUZUKI GSR750, KAWASAKI ZX-10R, SUZUKI SV650 ABS, SUZUKI SV650X, SUZUKI SV650, SUZUKI KATANA, SUZUKI GSX-R1000, SUZUKI GSX-R1000R, SUZUKI GSX1300R HAYABUSA, SUZUKI V-Strom1000 XT ABS, SUZUKI V-Strom1000 ABS, SUZUKI GSX-S1000GT, SUZUKI GSX-S1000F, DUCATI 999, DUCATI 999S, SUZUKI GSX-8S, SUZUKI GIXXER SF250
STANDBracket
I wish it was a little less expensive, but it's cool, so I'll take it. View detail
Can not be installed
To install, a screw-in StraightSocket covered by a Rubber Bush is inserted into the hollow hole in the Pivot shaft of the Swing Arm, but the K7 uses a Quantity:Pair (for Left and Right) The Brake Side (Right) is too small and cannot be installed because the attached parts are of the same size. In addition, it is thought that a new car can be installed, but in the case of my car with rust and dirt adhering to it, the Shift Side (Left), which is thought to be the same size, could not be inserted either.
Although it can be machined and installed, it is recommended to use another Manufacturer's
View detail
It's great.
The quality is good, Designma good. I hope it will not be active ^_^ View detail
Installation could not be done
The FTR223 could not be installed because the fixing part of the Chain Cover was changed in the middle of the process, but it could not be helped because of my lack of confirmation. The quality of the product is good and I think it would have been a good product if it had been installed. View detail