Reviews
Note that the fit is different from the Image photo!
Please note that the delivery is different from the product photo!
The Installation Instruction Manual also includes a photo of the actual installation so the Shield does not come to the top of the Light and will be installed with the previous Shield on.
I don't think it is worth $30,000!
View detail
Fits: SUZUKI GSX750S KATANA [Katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana].
Small for the price.
It's incredibly thin.
I'm afraid I'm going to cut my hand off at Edge.
I black-painted the back side of the camera so it would show through.
The mounting part is also made of LePera, so you need to balance it while tightening it.
The mountings are likely to crack easily with the slightest force applied.
I decided on this one for the Kobe Unicorn stuff, but it didn't work.
View detail
Fits: SUZUKI GSX750S, SUZUKI GSX1100S, SUZUKI GSX1000S
It needs to be processed.
I used it on the GSX750S2, but it was too vertical and I had to bend the STAND first. And the ground contact surface was also distorted by the heat of welding, so it was supported at one point. And the STANDSpring was not long enough and needed to be used separately. For this price, I think I would have been better off cutting, welding and painting the OEM STAND! 。 View detail
Fits: SUZUKI GSX1100S(SR)
Noncompliant products with a disregard for safety
In conclusion, it is not possible to install it
Harness length is 150mm shorter than that of the OEM parts, and the path it is supposed to take is It's not long enough at all
There is no explanation of the length of the product in the description section of the product, and you must immediately report the lack of length and replace it with a compatible product After three weeks of requesting it, the Sales Manufacturer responded with the following
'I apologize for the delay in responding
This product is shorter than OEM
In the case of the OEM, it is installed outside the front fork, but the
This product is made for the shortest possible mounting length
If you set the wiring to pass inside the front fork, there is no problem
What did you intend to set it 150mm short? The service manual also specifies the Harness route, and the Where is the necessity of passing diagonally underneath the Tank without going through HarnessClamp? We have actually installed it in the path described by this company, but the extra load on the coupler has been removed It took a lot of time and interfered with the operation of the Handlebar
After your response to me, in the description section of this product "Front fork is assumed to be wired through the inside In addition to this, there is the addition of words such as
It is disgusting to see companies that not only refuse to admit their mistakes, but also ignore safety You won't be buying a Manufacturer's product
View detail
Fits: SUZUKI GSX750S KATANA, SUZUKI GSX1100S KATANA
I was careless
In the Instruction Manual that I purchased and saw after opening it, "Since the foot hits the Side Stand, it is necessary to cancel the Stand switch. For Race "because it is not used. I hope I bought it at Point but - - -
It is unkind to not know unless the explanation to be included in the description of the product page is opened.
I can not trust things that only say good things.
View detail
Fits: SUZUKI GSX750S KATANA, SUZUKI GSX1100S KATANA
[a Webike Monitor] -- he was surprised -- -- this carries out 7000 yen or more -- -- out of which it was normal and came enough and which was carried out is obtained, and it never dabbles in this Brando
[a Webike Monitor] -- he
was surprised --
-- this carries out 7000 yen or more --
--
out of which it was normal and came enough and which was carried out is obtained, and it never dabbles in this Brando
View detail