Reviews
It's sticky, but...
I love it because it provides good protection for my Wiring. View detail
For Wiring Protection.
I like the texture, but it's floppy, so I guess it's not to everyone's taste. View detail
Cool.
Red Herringbone is cool. View detail
Cool.
Black Herringbone is cool. View detail
Recommendation.
I use this one where I can see Wiring, but it is hard to cut. View detail
For Wiring protection.
It's a little floppy, but it protects the wiring well. View detail
Cool
The performance does not change at all, but it is a product with a high degree of self-satisfaction. View detail
FashionWiring。
I use it where I can see. The cloth wrapped part is hard to cut, so it may not be easy to use. View detail
Show Wiring.
I use it where I can see the Wiring. The texture is very nice, but if you are not careful, the cloth wrapped part will cheat and go down. I think it's better to lightly sear the tip and then crimp it. View detail
Switch Cable Extension
Because I use the pipe handle, I bought the Switch Cable to extend my own work. It's not a problem if you keep the wiring drawing by yourself. View detail
Convenient handling of Wiring
It is useful when handling the wiring.
If you want to make the wiring along the harness, it is not a problem, but if you don't, the beauty of the wiring will change greatly depending on how you fix the wiring.
When you don't have a convenient place to hang your Tie Wrap, this product allows you to set up a fixed point by applying double-sided tape.
Moreover, the Tie Wrap is not attached to the body, but has a hole to pass the Tie Wrap through, so even if you cut the Tie Wrap when removing it, you can use it again and again by bringing a new Tie Wrap.
It's not the kind of thing you can't work without, but it will help you work cleanly and reliably.
View detail
Quality of the Wiring process jumps up.
When tinkering with the electrical components on the Self, one of the things that tends to get ugly is the insulation on the terminals that are used naked, such as the Bullet Terminal.
I think it's more Large ? to wrap Vinyl Tape around it and be done with it.
Of course, if you use a proper Vinyl Tape, there is no problem functionally, but I think that it often peels off and becomes stained after a long time, and above all, when you look back at it later, you feel disappointed with the handmade feeling.
That's where Heat Shrink Tube comes in.
It can be used to insulate exposed parts of terminals and wires, or to bundle a small number of wires for a dramatically more beautiful treatment.
If you go out with care, you can even create an OEM-like atmosphere.
Heat Shrink Tube itself can be obtained cheaply at Amaz◯n, etc., but this product is
Reel Sales
With adhesive
This is a feature of the system.
It is Merit to be able to cut it to any length you want, and above all, the effect of the adhesive increases the waterproofness when it is used to protect the exposed part.
To be honest, it's a bit pricey considering the amount of product that Sun Machine Level can't seem to use up, but I think it's an excellent functional product for that.
By the way, there is a method of roasting it with a lighter to contract it, but I recommend the use of the heat gun which is basically easy and certain.
View detail
For Ducati's MOSFETs
I bought it to convert my Ducati regulator to MOSFET, which is said to be easy to puncture.
I didn't want to modify the OEM body side harness, so I used this Coupler.
I must have had plenty of Model 110s on hand, but I couldn't find any 3-poles, so I was forced to buy one.
Type 110 Coupler was used for Generator side Connector of Regulator.
By the way, Battery side is 250 type 4-pole reverse lock.
I don't remember whether I used TAB or receptacle, but I was able to complete the MOSFET conversion successfully.
I only use one of them because I made use of the Harness and Coupler on the body side, but if it's only 300 yen, it's ok lol.
It is not this product, but if you can increase the Color variations a little more to the OEM Color Harness avs2.0 that the same DAYTONA has Lineup, you can completely align the OEM color, so I expect the Color variations addition.
View detail
Used for MOSFETs in Regulator
I bought it to convert my Ducati regulator to MOSFET, which is said to be easy to puncture.
I didn't want to modify the OEM body side harness, so I used this Coupler.
I don't usually use anything other than the 110 Coupler, so I looked for it quite a bit, but I didn't expect it to be so close by…….
I can't believe DAYTONA even has these in their line up.
Type 250 Coupler was used for Connector of Battery side of Regulator.
Since the coupler on the body side is alive, either TAB or receptacle is left over. (I've forgotten which one.) 。
Generator side is 110 type.
I would like to prepare a Harness of about avs2.0 because large electricity flows to a certain extent, but the OEM Color HarnessSeries of DAYTONA was a little short of color variations.
I gave up because it's not visible and it's Couplet-on so I can't make a mistake.
It's a bit frustrating to pay 500 yen to use one half of the Coupler, but I'm grateful for the lineup.
View detail
Used in License Plate LightWiring of WR250X
I used it with License Plate LightWiring.
For WR, the Brown wire on the body side was Plus and the Black wire was Minus.
I used it in connection with Y's Gear's Fender Eliminator Kit.
It can be connected without damaging the Wiring on the vehicle side.
View detail
You can connect and charge Battery with One-touch
I have posted before (https://imp.webike.net/article/0419666/) about the product that is the subject of the impregnation, but when I posted the impregnation Type of vehicle used (installed) column now appears, I'm reposting the Impreza with the vehicle type used set.
What made you decide to buy?
(I didn't buy the product (it came with the Battery Charger, which I will discuss later)
How was your experience with it?
It's a very convenient product because you can connect and charge the Battery with One-touch (TwoTouch if you include removing the dustproof Cap?) (Quantity):(See 1pc. eye post pics)!
In addition, the company's USB power supply (https://www.webike.net /sd/21440311/), but the Honda Sub harness ( (https://imp.webike.net/article/0363139/) and connected to the ACC power supply
You can also connect directly to Battery by using the in-play products (2nd post) (See photo)
By doing this, you don't have to turn on the main switch in an emergency It can be used to charge a cell phone from a motorcycle, for example
Was the installation difficult?
If access to the battery is not difficult (like Seat and If you don't remove the cover etc.), you can use the existing Power Cord on the Battery terminal It is easy to install, since all you have to do is to tighten it together with the
For the 400X, the installation was easy as you can easily Access the Battery by removing the Seat using the key (see the third posted photo).
【Please tell me the installation point and hang】
When not charging, the connection Coupler is pushed into the gap of the Seat frame (Quantity:1 Set of 4pcs. (See the photo posted in the eye)
However, the Coupler comes with a Cap, but you can find it on the company's website (https://www. daytona.co.uk/products/single-71637-genre) if you look at it In fact, put it in a place where it won't get rained on (Perhaps that's why the product name is "With a waterproof cap not "With a dust cap In case of rainy weather, the Connection Cord is stored under Seat
[Was there anything that disappointed you?
Temperature is lowMaterial:When the Rubber's Dustproof Cap is hardened, it can be difficult to remove the Cap from/attach it to the Connection Coupler.
In that case, I remove and install the Dustproof Cap while inserting the Slotted screwdriver.
[Was the Instruction Manual easy to understand?
(Omitted since I didn't buy the product.)
[Included Parts:were they on?
(Omitted since I didn't buy the product.)
Do you have any wishes or improvements you would like to make for the Manufacturer?
I would like to see the dust cap on the connection Coupler improved so that it can be easily removed and attached even when the temperature is low.
I also hope that the price will be lower than the following USB power supply
[Do you have any products to compare it to?
・DAYTONA：Motorcycle Power Supply USB 1Pot
(https://www.webike.net/sd/22060420/)
The Connection Coupler used in this product is the same as the one used in the product in question It is the same shape as the Connection Coupler
Because the price is cheaper here, if there is a use of the USB terminal side, I think that it is good to buy here.
DAYTONA：Display Battery ChargerRepair item Body Connection Harness
(https://www.webike.net/sd/22060427/)
The connection coupler used in this product is the company's "Display Battery Charger Other than (https://www.webike.net/sd/21922914/) Charger and USB power supply (https://www.webike. net/brand/177/series/21942/), the connection used in Note that the shape of the coupler is different from that of the coupler and cannot be connected to them
[Others]
The company's "SwitchingBattery charger 12V (https://imp.webike.net/article/0419564/) It comes with 1pc. of in-play items as Included Parts:
If you own more than one Motorcycle, it would be a good idea to purchase the amount you need.
View detail
A wide variety of products
I like that there are so many different types to choose from for different purposes.
However, it is quite expensive compared to the quantity sales at specialty stores.
But you buy them because they're so convenient to get anywhere.
View detail
It also prevents Wiring from being bent.
The foreign-made extremely SmallBlinker's Wiring is very thin, isn't it?
I'm afraid I'm going to have to use a Shrinkable Tube for fear of breaking the wire at the slightest thing.
and wrapped it with a reticulated protective tube.
If you heat it up, it will shrink normally, so it's just a matter of fine-tuning how far you want it to shrink.
View detail
I was able to position Blinker!
It has already been changed to KIJIMA's LED Blinker, and Blinker positioning was done as an additional function.
I'm very happy with this product.
View detail
You can arrange freely.
It can be used in a wide variety of ways. I used the Bracket to move the Normal horne from one place to another, and it is easy to work with, light and strong. View detail