Reviews
I would like to have a larger size!
Purchased as a countermeasure for Enduro race, which is expected to be in muddy condition.
If mud gets into the gaps in the Under Guard, it will make it much heavier and washing the car will be Large strange.
The countermeasure is to fill the gap with this Sponge.
It worked well in actual driving, bouncing mud off the ground.
SpongeQuantity even if you use it for Off-roadFull size vehicles if you want.:I felt that it would be better if they could sell it in a large size so that only 1 pc. is needed.
View detail
ZETA Zita ED Skid plate
[How is it used?
Was the one you received as per Image? Street Image
How was your experience with it? Strength.
[Points to note] The minimum vehicle height is lowered by the Frame plate.
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
countermeasures against mud
[How is it used?
Situation that cannot be avoided when playing Enduro with HUSQVARNA TE250i Muddy." I think that the secret to longevity is how much we can enjoy this Condition. I feel that the secret to a long life is how much you can enjoy this Condition.
I don't dislike driving in the mud that much, but I can't help but fall over or run in a swamp. Mud, dirt and others are heaped onto the Motorcycle in Large quantities.
this "Mud." One article reported that the weight of the car before and after driving in Muddy condition can change by nearly 20 kg due to the mud adhesion factor.
I was convinced when I read the article that it was really my motorcycle that had fallen over with mud on it.
If that's the case, let's take various measures to prevent mud from sticking! So, I'm an Off-Roader-Large lover. Dirt ace" Ya Silicon spray. I sprayed a large amount of "Mud" and drove around. The feeling was that it was better than nothing, but the mud adhesion was not that small because of the spray.
Then, let's physically prevent mud contamination! That is why we put on this Sponge.
DirtFreak has also released a Formetc. to be attached to the FenderReverse side, but we heard that it is difficult to remove it once it is attached to the Fender, so we were the first to install this Form, which seems to physically prevent mud from mixing in by putting it in the gap.
How Large is Large? We didn't even know how much we needed for the Husk, so we used the Quantity:2 Set is purchased and installed.
As you can see in the image, we put it between OEMGuard and Engine.
Actually used about half of 1pc. Quantity:2pc. No Set was needed either.
I installed it and had a Race with Muddy running, so I actually used it, but I feel it is lighter because it is indeed physically free of mud. Washing the car also became somewhat easier, so it is effective for the price.
I was concerned about the heat resistance with Engine heat, but I used it for 1Race2 hours and had no problem at all.
I think everyone should install Enduro rider.
Was the one you received as per Image?
How was your experience with it?
[Points to note]
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Just in case.
[How is it used?
I bought this together with my CRF125F. I am still breaking in the bike and have not driven it in a way that makes me worry about the undercarriage.
Was the one you received as per Image?
It is thick enough, and the bracket attached to the frame makes it more secure.
Was the installation difficult?
It is not difficult, but it is a CHINA Motorcycle. I did it by standing it on the wall.
How was your experience with it?
I have only just installed it, but the fitting is good and it looks like I can run GunGun.
[Included Parts:were they on?
We had everything we needed for installation.
[Was there anything that disappointed you?
The Bolt that comes with it is cheap.
View detail
self-satisfaction
Remove the stop Screw and replace it with an OEM Guard.
If you have the tools, it is easy to pontificate.
Not so obvious, One point.
View detail
Installed on SEROW250
Since DAYTONA's EngineSIDEGuard was already installed on SEROW, a simple Under Guard was installed.
Installed with 4 Screws.
It is Simple, but when it is running, it makes a clunking sound, so it seems to be Guarding the Engine.
View detail
Better quality than OEM
Easy replacement with tools!
It seems to fulfill the role better than OEM.
View detail
so good
so good View detail
Change of Skid plate
The Rally skid plate is plastic, so it has been modified to avoid damage to the engine in case of accident. The installation can be done by an amateur. However, there is no Instruction Manual for installation, so I referred to the video on the application page. View detail
Relief
They are protecting Engine well.
Good job.
View detail
He's doing his job.
They are protecting Engine well. View detail
Very Good Quality
Great quality of the materials, skid plate is well protected and all the components individually packed. Looks great in my Grom and does cover a good portion of the engine. Highly recommended! Unfortunately the installation manual received was in japanese, so needed to google all the instructions to be clear on all instructions, but wasn't a big deal. Special note for those who installed a custom exhaust because it may not fit. I do have a Vanes & Hines hi-output Hooligan, and needed to modify slightly the bottom holding bracket to ensure won't damage the exhaust pipe, but even with 3 of the screws holding the skid plate is very solid. View detail
Fits: KAWASAKI KLX230, KAWASAKI KLX230S, KAWASAKI KLX230R, KAWASAKI KLX230R S
The construction is very careful and solid Guard, but there is interference with the exhaust pipe.
[How is it used?
OffRoad course driving
Was the one you received as per Image?
Lighter than expected.
Was the installation difficult?
The exhaust pipe interferes a little with the bolt. Also, the two front bolts and one rear bolt are positioned too tight, so be careful not to turn the bolt too far because the screws may be damaged if the bolt is not rotated.
How was your experience with it?
Large sturdy enough to climb over rocks and logs.
The fixed Bolt is designed to prevent the head from popping out.
Oil replacement is possible, but it is easier to remove the oil filter for oil filter replacement.
[Was there anything that disappointed you?
None except interference with Exhaust pipe.
[Opinions and requests to Manufacturer
Please fix the interference Point with Exhaust pipe.
View detail
ZETA Zita Enduro Sucido Plate installation
It's well made and Covers the sides, so it feels secure. View detail
KITACO Skid Plate
Plate was well made had all the hardware included fit perfectly looks great the directions are very easy to follow just by looking at the pictures I'm very satisfied with my purchase shipping was very fast View detail
Steady bitter
Quality, finish, no complaints!
It is indeed ACERBIS.
View detail
It needed to be processed.
I bought the OEM Skid plate because it was too expensive.
We considered SRC's, but it would require removing the Bolt under the Engine and then installing it.
We chose this one made by ZETA, which can be installed with 4 bolts.
Regarding installation, the Bolt enters at an angle, so the screw hole was likely to be damaged.
I ended up shaving 2mm off the Bolt hole at the back and installed it.
It may be an individual difference, but I was a little disappointed because it is not a cheap item.
View detail
Fits: BETA RR 350, BETA RR 390, BETA RR 430, BETA RR 480, BETA RR 500
Much better than I expected.
I'm definitely glad I went for the Polisport skid plate.I run the Polisport clutch cover and ignition cover too the that all work great ! Excellent product for an excellent price.It's east to put on and off and was half the price of everything else. Its not very obvious in photos or a video, but the plastic is much more rigid than it looks. (And also a better weight choice than aluminum.) Total coverage is great, and toolless install/removal is sweeet. No fitment issues at all. It pops right on and is flush with the frame. the first ride I went over some rocks and it held up just fine. I love how quick it is to put on and take off. View detail
Rugged OEM Product
We chose OEM because it seemed to be sturdy, though pricey.
I asked Shop to do the installation because it seemed complicated.
View detail
Cannot be installed due to poor manufacturing accuracy.
In the past, there have been a number of reviews that the mounting holes did not fit or the screw threads on the frame side were napped, but the manufacturing accuracy has not yet been improved. However, the manufacturing accuracy has not yet been improved, and there is a possibility that some of the inaccurate products that have already been distributed are still out in the market without being inspected.
In fact, no matter what I did with this product over several hours, the Frame and Bolt holes did not line up, but Y's Gear's Guard completed the installation in one minute.
If you have a similar situation, you should return it before you ruin the Screw mountain on the Frame side.
However, similar comments have been made in the past, and it is unclear when the fundamental manufacturing process will be improved.
View detail