Reviews
Fits perfect with OEM lamp
I like shorter version of OEM rear lamp. I'm happy. If you live in europe you can use original licence plate holder. ,:))) View detail
You can also substitute OEMBracket.
The OEMBracket broke unintentionally and went into Reflector" Les" status.
Although it was difficult to obtain an OEMBracket, Moto Crazy's parts can be substituted for the OEM.
Thanks.
Installation can be done using the Rear Fender intermediate bolt.
The Reflector itself was prepared by OEM, but was repaired inexpensively.
I think it is because it is pointing downward rather than comfortably level, but that would be a judgment call for the inspector in charge.
View detail
fenderless
[How is it used?
Was the one you received as per Image?
It was as expected.
How was your experience with it?
It has a much smarter look.
[Points to note]
If you don't slow down at large bumps, the Reflector may come in contact with the Tire and damage it.
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Installation is Large
Was the installation difficult?
It is quite Large strange for one person to install.
The License Plate Light cannot be adjusted after installation.
How was your experience with it?
Wiring is almost invisible and looks nice and Refreshing.
View detail
just right (time, size, length, etc.)
[How is it used?
Was the one you received as per Image?
Compact over Image
Was the installation difficult?
Instructions are included, so anyone with tools can do it.
How was your experience with it?
This is my first Fender Eliminator Kit, so I don't know about others, but it's good!
[Included Parts:were they on?
[Was there anything that disappointed you?
None
View detail
Fits: DUCATI 1199Panigale, DUCATI 959Panigale, DUCATI 899Panigale, DUCATI 1299Panigale, DUCATI PANIGALE V2
Be careful only to lick Bolt
Installation is very easy, but the bolt on the oil cooler core guard is very tight, so I had to use a Neji-saurus to forcibly remove the bolt and replace it with a normal Hexagon Socket bolt. I think the quality of the core guard itself is good and the guard performance is sufficient. View detail
I hope this is helpful to you.
for DUCATI Parts with a little modification to BMW.XR. View detail
Fits: DUCATI Monster 821, DUCATI Monster 797, DUCATI Monster 1200, DUCATI SUPERSPORT 950, DUCATI SUPERSPORT 950S, DUCATI SUPERSPORT 939S, DUCATI SUPERSPORT 939, DUCATI Monster 1200S
It took a lot of work, but Parenthesis is great!
The M821 has a complete design including the Rear Fender, but I still want to make it a Fender Eliminator and have it Refreshing! I bought it because I thought it would be a good idea.
The installation itself was easy, but there were a few troublesome parts that took longer than expected.
I had a hard time 1. removing the pure normal thread screw in the bracket of the blinker and 2. screwing the body of the Fender Eliminator onto the body. I think we can proceed.
Also note that drilling is required when using OEM License Plate Bracket.
View detail
be stooped
The look is quite different compared to OEMFender. You will also feel a strong sense of satisfaction.
I think it is a good idea to check if the included ShortParts are sufficient for the job. I had to run to a hardware store because I was missing the nut that is used to hold the License Plate Bolt. The instruction manual says Original Nut" Original Washer It was stated.
The installation can be done according to the Instruction Manual without any difficulties. However, since the Instruction Manual does not mention how to remove the OEM parts, it is better to check the Service Manual. I was not sure and had to remove the Rivet in order to remove the OEM reflector, but in fact, I was able to crack the Fender without disassembling the Rivet. (Sweat)
The Locktite and Hex wrench were originally owned, and the Hex lobe wrench was bought for the need for T10 and T20.
View detail
Fits: DUCATI Monster 1200, DUCATI Monster 821, DUCATI Multistrada 1200, DUCATI SCRAMBLER, DUCATI STREETFIGHTER, DUCATI Monster796, DUCATI MONSTER696, DUCATI MONSTER1100/S, DUCATI Monster 1200, DUCATI Monster 821, DUCATI Multistrada 1200, DUCATI SCRAMBLER, DUCATI STREETFIGHTER, DUCATI Monster796, DUCATI MONSTER696, DUCATI MONSTER1100/S
I took it for granted, but …
DUCATI doesn't have a stick to make the side stand easier, which is common in Japanese cars.
It's hard to STAND.
Thanks to thisParts for the help.
View detail
Fits: KTM 125DUKE, KTM RC125, KTM 200DUKE, KTM RC200, KTM 250DUKE, KTM RC250, KTM 390DUKE, KTM RC390
Same as Film on your phone.
It's a Film just like the Film on your phone.
But it's not GlassFilm, so it's what we call a PelePera.
It is possible to install it easily if you pay attention only to the pasting position a little.
I'm almost certain that the Meter won't get damaged, but I put it on just in case.
View detail
Fits: DUCATI Streetfighter S, DUCATI Streetfighter, DUCATI STREETFIGHTER848, DUCATI Streetfighter S, DUCATI Streetfighter, DUCATI STREETFIGHTER848
Large sturdy if you look at the Instruction Manual properly.
AssemblyInstruction Manual is included and it was relatively easy to replace the OEM Blinker.
LED Sequential Blinker (Rizoma (Part Number)):(FR130B)), I had considerable difficulty in replacing it.
The cord storage space is too small and the cords for attaching the resistors are too bulky to store.
So the resistor was connected to Front and somehow completed. But then...
When I assembled all of them, the license plate hid the blinker.
So furthermore, Posh (POSH) I bought an extension bracket 40mm for sequential.
All redone. I enjoyed it for a few days.
View detail
Fits: DUCATI PAUL SMART1000LE, DUCATI SPORT1000, DUCATI GT1000, DUCATI SPORT1000, DUCATI GT1000, DUCATI SPORT1000
Refreshing around the rear!
Although it is not written in the manual, I think that it takes a little time for a beginner because there is an installation order. I think that it is somewhat easy to assemble if you fix the back part that cannot be retightened afterwards first, and proceed with the temporary tightening of the others.
The workmanship is not bad for the price, and Refreshing around the Rear.
View detail
Fits: DUCATI MONSTER 1200S, DUCATI MONSTER 1200, DUCATI MONSTER 1200R
They're doing a great job
I purchased this product because of its cost effectiveness No holes were not aligned or otherwise inaccurate when installed, and they are still in place after driving The MONSTER S21200 series received Garbage Be careful not to crush the Core when you install the Radiator because it is curved You need to put it on View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1299Panigale, DUCATI 1199Panigale, DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1299Panigale, DUCATI 1199Panigale
Cost-effective!
Many external for vehicles are expensive, using imported products and carbon parts, but I have no complaints with this one The Panigale is a Tail Lamp and Blinker in one piece, and the BlinkerLight is The type that doesn't protrude from the body is popular, but I'm using the LED type of OEM It is very Compact and does not interfere with the body design It is very Compact and does not interfere with the body design I think it's safer because it's easier to check than it is to check the Number angle and the quality Not bad
It's a good costumer!
View detail
Neatly organized around the rear
It took me a while to remove the OEM Fender? Refreshingly, it's nice to see the License Plate Light connected We need to do some processing, but I've been using commercially available Waterproof I changed to Connector and made the coupler to insert and remove the license plate The Cable of the License Plate Light of the product is short, and I am worried about the cable of my F4 In the event that the engine cannot be retracted to the body (under the Tandem seat), the Exhaust There is a hole for the Cable in the SystemCenter area, and the Connector section comes in the hole for the Cable It's not a good idea Cable length should be 15-20% longer than that of the original It's a good way to get it delivered View detail
Fits: DUCATI SCRAMBLER, DUCATI SCRAMBLER
it is better to have it than not
It was originally a used car body with Wound on it, but I bought it so that it wouldn't stick any more!
Adhesion was able to be done easily with adsorption, but the edge where Clearance is large is a little empty I think it's necessary before Wound causes diffuse reflections and makes it hard to see
View detail
Fits: DUCATI Monster 1200, DUCATI Monster 821, DUCATI Multistrada 1200, DUCATI SCRAMBLER, DUCATI STREETFIGHTER, DUCATI Monster796, DUCATI MONSTER696, DUCATI MONSTER1100/S, DUCATI Monster 1200, DUCATI Monster 821, DUCATI Multistrada 1200, DUCATI SCRAMBLER, DUCATI STREETFIGHTER, DUCATI Monster796, DUCATI MONSTER696, DUCATI MONSTER1100/S
essential
I felt that SCRAMBLER was difficult to take out Side Stand, but I was able to make Stand End I thought I could manage to put it on, but in the end I couldn't, so I installed it after a while since I bought it
After I installed it, I wondered why I didn't install it sooner..
Installation is a Universal Product, so some tolerance is needed, but it is not necessary to tighten it I thought there was a possibility of loosening even if I got into it, so I made STANDBody to prevent rotation I applied Locktite to prevent it from loosening
View detail
Fits: KTM 125DUKE, KTM RC125, KTM 200DUKE, KTM RC200, KTM 250DUKE, KTM RC250, KTM 390DUKE, KTM RC390
I'm not sure if I should have
It's a protective film!
This is an impulse buy
It's SiliconFilm, so it's less sensitive than Glass
Cost is also reasonable considering the screen size
Is it a UV protection? In the hopes that..
View detail
Fits: DUCATI 1098, DUCATI 1198, DUCATI 848, DUCATI 1098, DUCATI 1198, DUCATI 848
Helpful Items
Because there is no SIDEStand Hook on the motorcycle that I purchased, it is a substitute for Size I bought it after checking only
It's not pushed as a compatible car, but I managed to install it safely and it's easy to put the Side Stand in and out It's easier now
To be honest, I was worried about the tapered shape of the tape to make it fall off, so I decided to stop the hexagon nuts of both SIDEs from loosening Quantity from the back part as it looks like a Nut:Screw lock was applied to Set Fixed Bolt
Because it is a product that does not have a welded structure and is light, the side stand can rattle when there is a slight difference in level I've been able to use it comfortably so far without dancing, so I'm evaluating it with high hopes
View detail