Reviews
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
Feeling of security
I always had a hard time hanging the Maintenance Stand on the Swing Arm, but by fixing the front tire to the ClampSTAND, the stability is increased and the Maintenance Stand can be used with ease. View detail
I will never buy from them again.
I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail
As a replacement for OEMBlinker relay
I bought a battered 900SS (900SL) and am Restore.
In this situation, RearBlinker decided to change to ultra-small type LED's for various reasons.
The front is a Cowl recessed type, but since this is part of the body design, it is used as is, and the light bulbs inside are not converted to LEDs, but are left as they are.
This would be a hassle with bulbs in the Front and LEDs in the Rear, but times have evolved and there is now ICRelay, which supports a variety of wattages and makes everything look good.
The problem is replacing that ICRelay with the original Relay.
For ordinary Japanese cars, it is a 2-pole universal layout, so all you have to do is plug in the Conversion Connector that comes with the Relay, but unfortunately, DUCATI is a 3-pole Relay.
In addition, the connector is fixed to the body of the car, and the Relay is inserted into it, which is the opposite arrangement from that of domestic cars.
(For domestic cars, the RelayBody is mounted on the car body, and the Connector extending from the Harness is inserted into it.)
So we decided to disconnect and discard the UniversalConnector (Female side) from Relay and make our own Conversion Connector that would be Male-Male.
After carefully checking the terminal shape of the OEMRelay, I realized that it is the same as the H4Headlight Connector.
So I bought this Kit to create H4Connector.
Although there are a variety of female connectors that can be used with H4 Valve, there are only a few that can be used to create male connectors that reproduce the shape of the Valve.:Set is appreciated!
Unfortunately, the H4 and OEMRelay terminals had different widths, although the connector shape was correct.
The OEMRelay terminal width is about 6.4mm, and this H4 terminal is about 7.7mm wide, about 1.3mm thicker, so Quantity:Pair (for Left and Right) was shaved and prepared 0.6mm at a time.
However, the terminals are generated by folding a flat plate 180° with PRESS, so if both ends of the terminal are shaved, the folded part is lost and becomes RoseRose.
To avoid RoseRose, before shaving both ends, solder is poured inside the terminal to fix the PRESSED board firmly in place, and then both ends are shaved...Relay terminal is completed!
The completed terminal has a different width at the insertion point, but the rest of the terminal remains the normal H4 terminal shape, so it can be used by inserting it into an H4Socket as usual.
Just check the terminal positions of ICRelay and OEMRelay (they were in a position relationship that would not function if you stuck them in as they were) and assemble them.
We were able to connect the Relay receiving Connector on the car body side and the replaced ICRelay Connector while converting well.
The terminals included in the Connector set are gold-plated and magnificent, and their shape and strength are quite normal and perfect.
Male of H4Connector. It should be a rare occurrence, but if you are having trouble with HID or LED wiring, this is the perfect solution.
View detail
Just right!
In general maintenance
This amount should be enough.
View detail
Convenient to have. Used during car wash
[Usage]
I use it when I wash my Motorcycle to prevent water from getting in through the Exhaust System. I used to use Dustcloth as a substitute, but this product is easier to use. Conversely, it is a product that can be used as a substitute, so I feel the price is a little high.
[Feeling of use]
Just plug it into the Exhaust System outlet before washing the car.
Since the part to be inserted is rubber, there is no risk of scratching the exhaust system when it is inserted.
(Points to note)
The Rubber on the insert is hard, so you need to push a little harder when inserting it.
Sealability seems to be there. It is not a product that is completely waterproofSeal.
View detail
ExactlyFit!!
YAZAWA [ YAZAWA SANGYO ] Gasoline portable can Mini Tank 2.5L [ Part No. ] MT3 I purchased this product because the aluminum cap of my "X" was deteriorating! Aluminum caps tend to deteriorate easily, so I am glad that there are repair parts! View detail
If used gently, it will last somewhat longer.
[How is it used?
It is used during Tire replacement &Puncture repair work on Dual Par Pass cars.
Many Dual PurPass vehicles that enjoy mountain play and forest roads use a Tube in the Tire, so these Items are very useful for getting the Valve of the Tube out of the Valve hole in the Rim.
Wire is thin, so be careful when working with it, as the handle clasp can easily come off or the wire can easily break if pulled with force.
Did you receive the item as per the Image?
I used to use a similar product from another manufacturer, but it was used roughly and broke, so I bought this product, which was a little cheaper at Webike at the time.
The product was as per the Image.
How did you like it?
Once you get the hang of it, you can easily pull out the Air Valve in no time at all.
Especially in winter, when tires become hard, I can't do without this product.
[Points to note]
As I wrote above and others have written. "Forced to pull by brute force." The product is fragile when you try to pull it out.
Although Manufacturer is different, if you search for DRCAir Valve Puller in the product introduction section of Webike, you will find a video at the bottom left of the introduction section that explains it in an easy-to-understand manner. If you are not sure how to use it, please refer to the video on YouTube.
How did it compare to other products?
I used to use DRC's Air Valve Puller before this product, and my personal impression is that it was easier to use DRC's Air Valve Puller because the Wire tends to rotate when Screw-tightening the Valve. (Possible individual differences) 。
Other items that would be helpful
Point and hang of installation
With your free hand, press lightly on the backside of the valve of the tube toward the rim while guiding the tube.
The rest, as I mentioned above, you can watch the video.
Basics We're not in a hurry. We're going to do our job well and reliably." is the best shortcut.
[ITEMS TO BUY TOGETHER
Prepare Lever, BEETWax, Inflatoretc. for Tire removal and attachment separately from the things to be replaced.
[Opinions and requests to Manufacturer
It would be nice if you could use a stronger wire to ensure durability, but we would be grateful if you could just keep this product in the lineup.
View detail
Spring hook
It is used for spring removal and attachment of the Exhaust System.
The Type is a little long, so it seems to be easy to apply force when pulling, but in some places the long length gets in the way and makes it hard to work with.
It is good that it can be split into two parts, can be removed, and can be pulled by swinging it at an angle, but it turns too much and cannot be pulled properly, making it difficult to install the spring hook.
View detail
Slightly Large size! Ease of use on the high street!
Slightly Large Size:I bought these because I wanted Free military gloves. They are non-slip, easy to use, and at a low price that I don't hesitate to throw away when they get dirty! I have seen some high quality military gloves on the market, but I think these are the easiest to use! View detail
Rear stand hanging is easy
I found the product by chance, searched for it on Webic and bought it. It is super easy to hang Rear stand especially in Garage. I wish I had bought it from the beginning. I highly recommend it. View detail
Oil change
Used when injecting gear oil.
The Bellows one that comes with the Oil is fine, but this one seems better for Oil injection because it can be shrunk with Silicon and the angle is easier to work with.
It is not used that often, but it is an expensive product, so if you have 1 pc. you can use it for various purposes.
View detail
Preliminary Fuse
Quantity for spare Fuse:This selling price for 1 Set of 3pcs. is inexpensive, which is helpful. I don't think I will use all of them. View detail
Purchased OilDrain tank4L Satisfied
I was looking for the smallest type of OilDrain tank. 4L is the smallest and cheapest, so I bought it immediately. 4L is just right for my GROM which has 900 liters of oil, so it will be useful for oil and fluid replacement.
The only disappointment is that when the Cap is opened, the Oil drain bolt just about fits through the hole.
But after careful consideration, I cut out the cap of the plastic bottle and inserted it with a hole in the middle so that it would not drop in.
I'm satisfied
View detail
Perfect for 2nd Silencer.
Used for storage of RM125
It was Exactly to the Silencer exit Size of the 2nd vehicle.
I recommend it because of its low price.
View detail
Preliminary Fuse
When I exchanged Main's Harness for Other Brand Product, it was a MINI flat type, so I bought it as a spare.
The price is reasonable and Quantity:1 Set of 3pcs. so I don't think I will use all of them, but it is worth having.
View detail
Just right for disposable
[How is it used?
Used to clean parts during Restore of TZr50R.
I bought it because the price was low and the tips of the hairs I had before were becoming stiff.
How was your experience with it?
It was easy to hold and use.
The small size also makes it easy to clean the smallest of areas.
However, it may not be suitable for cleaning Large objects.
How did it compare to other products?
Although the quality is much lower than the slightly more expensive Brush, it was great for a simple cleaning of the Sunday mechanic. Especially when it comes to Restore, these supplies are cheaper and larger in quantity than in quality.
[Points to note]
There are three types of bristle tips, but use them with caution, as they may damage parts if used incorrectly.
View detail
Connection
It is used for redoing Wiring.
Just Right Quantity:It was just the right number of pieces to reASSY in a set.
View detail
Convenient
Usable as normal. I bought it for measuring Fork oil. I think it is good to have several of them. View detail
For cleaning.
I bought it because it seems useful for cleaning carburetor and for cleaning tight places.
Quantity:1 Set of 5pcs. so it can be used in different places, which seems convenient.
View detail