Reviews
Essential Items when replacing Tire
[How is it used?
I use it every time I change a tire on my Racer YZF-R25.
In a race, the front wheel balance is especially important because of the speed range.
Since my vehicle has a slightly shaken wheel due to a fall, this is an even more essential item.
How was your experience with it?
I used to use Jay Trip's Weight, but this time I went with Battle factory because they had it in stock.
To be honest, it is just lead, so there is no good or bad, but Battle factory is Shiningly more Beauty to look at.
How did it compare to other products?
It is comparable to Jay Trip. If I had to say something, I would say how easy it is to peel off the adhesive side.
This is also difficult to remove from Battle factory, and even if you pry it off, the Sponge portion of the Double-sided Tape remains.
It's better than peeling off, so that's good.
I would also like to see a Black color since Coloring is only available in Silver.
I don't mind the Racer, but when I put it on my town car, it will stand out if the wheel is black.
[Points to note]
When attaching Weight to Wheel, be sure to degrease Wheel thoroughly before attaching.
Failure to degrease the adhesive part of Weight will weaken it, and it may peel off and fly away during driving.
I am lowering the Risk of skipping by dewaxing→pasting→Black adhesive Tape on top of the Weight.
I see that all the vehicles that run on Circuit are reinforced by taping on Weight.
View detail
Posh Footpeg Up Plate replacement from attached ROD
The Posh Footpeg Up Plate was installed from the time the vehicle was purchased, but as many people have said, using the included ROD, the 2nd and 3rd positions can only be used by shifting the Piece on the Mission side, and with that, the lever position adjustment is not wide enough, and furthermore, the shift change intervals around 5th and 6th gears are not comfortable. In addition, the shift change interval around 5th and 6th gear was not comfortable, so we replaced it.
The length of the ROD was arranged in advance according to the lever position to be determined, so after installation, the ROD can be used at any position on the Plate.
The price is reasonable because I can arrange for a specific length, and the precision of the screw cut is perfect with the stainless shaft.
View detail
Shift rods are usually Normal Thread Screw and Opposite Thread Screw.
I ordered it thinking that it might be Normal Thread Screw and Opposite Thread Screw because it is a Shift rod. I thought it was okay if I could not adjust the rod end by diverting it, and it was also troublesome to buy an additional rod end, so I purchased it based on an amateur mistake.
I ended up buying Stainless Steel round steel and made it myself. It ended up being very cheap.
View detail
I am the one who wrote the Impression on the order of both screws.
I could not install it because I had diverted it in various ways. I had ordered both screws, but I was mistaken, Webike never answers the phone, so I contacted Battle factory and they said that Opposite Thread Screws and Normal Thread Screws are the norm. I apologize for being an amateur, but please be careful when ordering Shift-related parts for other vehicles. I may be the only one. View detail
I ordered both screws, but one of them came with a reverse thread.
I needed it in a hurry and asked for a return and exchange, but the reply was slow, so I called Webike and there was no answer at all. I called Battle factory, but they still can't help me unless I ask Webike. I am really disappointed. If they were quick to respond, I would have nothing to worry about, but since they are slow to respond, I feel bad. I'm worried that they will really return or exchange the product. View detail
Convenient
Since the length can be selected in 10mm increments, I measured the length I needed and purchased it. View detail
Tzr250 bodywork
Battle factory tzr250 bodywork is excellent quality and the purchasing from webbike was great , will order more parts in the future View detail
Cospa strongest
I bought it because I needed a spare to run Circuit. View detail
I like that it's light and doesn't take up much space.
I have been using JTrip's STAND before and after for my 3.5 liter class, 250 class and NSF. It is very light due to the material. It also does not take up much space in the Transporter. However, I can't deny the instability while using it compared to JTrip's product mentioned above. That's why I gave it a Point4. I can't help it because of its shape. It also requires a certain amount of physical strength when you want to lift the vehicle. Women may find it a bit large. That's why I chose Point 3 for the work kill. However, JTrip's products are stable, but they take up a lot of space when stored. So I think you should choose one depending on your purpose. I am also satisfied with BF products. View detail
It came on with almost no work.
There are few gaps in the holes, which is common in FRP parts, and it was attached with almost no processing. View detail
Installation Battle factory bar!
[How is it used?
In use for shopping, wandering, etc.
This time the stick used as Shift LinkageROD
Was the one you received as per Image?
Yes, sir!
Was the installation difficult?
No! There was no difference between the OEMShift rod and the installation.
How was your experience with it?
The quality and processing accuracy are good.
There are some spiral cutting marks on the shaft, and it seems to be made by lathe.
Large change is beautiful!
[Included Parts:were they on?
No, sir! There's nothing on it.
It's unlikely to be there in the first place.
[Was there anything that disappointed you?
That didn't happen either.
Other items that would be helpful
Point and hang of installation
As long as the Female Screw in the pillow is sound, you only have to screw it in.
[Availability and clarity of the Instruction Manual
No! (You don't need it in the first place. People who don't understand the structure don't buy these things.)
[Notes]
Be careful not to select the wrong ROD length.
These are the parts that will be needed if you start to modify the Shift relation without permission.
If your car has no abnormality or dissatisfaction in the current situation, you will not know the effect of replacing it.
In a bad way, it's just Shaft for Shift.
NORMAL is considered to be steel, but it is the result of being required to be able to bend without breaking and cutting in the event of an emergency such as a fall.
This is Material:It is made of Stainless Steel and hard, so it is difficult to bend and may break (don't get hurt!)
It is not a violation to use it on public roads, but it must be used with a good understanding.
You can buy a longer one and cut it to adjust it (though it's hard because it's Stainless).
[ITEMS TO BUY TOGETHER
M6StainlessNut and M6Left Screw StainlessNut if you want to have different colors.
[Opinions and requests to Manufacturer
It's a little pricey (crying)
View detail
The faster the Situation, the more important it is.
[How is it used?
I used it to replace the tires on my Racer motorcycle.
Was the one you received as per Image?
It is a weight, so it did not differ from Image.
It is surprisingly soft to the touch and can be bent to fit the curved surface of the Wheel.
Was the installation difficult?
Balancing the Wheel is tough without a Balancer.
If you don't have the environment to take the balance yourself, it is safer to let the store do it for you.
How was your experience with it?
The Balancer itself is designed to be attached with Double-sided Tape, but I put more Tape on top of the paste. When I tried to remove the tape when replacing it, it was very sticky, so I didn't feel like it would come off easily.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
It can be used for the current model without any problem.
I've been using it on my current model since 2019 and it works perfectly fine.
I think the ease of use is the same for all models.
By the way, I used it for many years with Ape 50 and CB400SF.
View detail
Fits: APRILIA RSV1000, HONDA CBR250R, YAMAHA YZF-R6, YAMAHA YZF-R25, KAWASAKI ZX-6R, SUZUKI GSX-R600, HONDA NSR250, HONDA CBR600, HONDA CBR600RR, HONDA CBR900RR FIRE BLADE, HONDA CBR929RR FIRE BLADE, HONDA RVF750, KAWASAKI NINJA2 Helmet50 , KAWASAKI NINJA2 Helmet50R
Increased strength
I use it on Universal and it has increased in strength.
Shift feeling is also improved.
View detail
Secure Grip
The Edge of the Knurl is standing and has high Grip power.
The Sole of the shoe is more susceptible to Damage, but I don't care because the Merit is a Large threshold.
If the screw hole size, pitch and width are correct, we recommend replacing the footpeg with another manufacturer's footpeg.
View detail
2001 R6Front Fender
The existing Fender did not have 10mm clearance between the 120/60-17in.
The Fender that I replaced had a gap of about 15mm between 120/70-17in. and the Warmer as shown in the picture.
I was able to install it with room to spare.
View detail
Fits: HONDA CBR1000RR, KAWASAKI NINJA2 Helmet50RR, HONDA RS125, HONDA RS250, HONDA NSF250R, HONDA CBR600RR, HONDA VTR250, YAMAHA YZF-R1, YAMAHA YZF-R6, KAWASAKI ZX-6R, SUZUKI GSX-R600, SUZUKI GSX-R1000
Perfect for Repairing Rear Sets!
I always have one set as a repair for my race car.
Knurl also grips well with Sugar Crystal, so you can get a good grip. Recommendation Footpeg.
If you get rid of it, rotate the Footpeg to get a clean surface and the Grip will come back.
It tipped over a few times, but it did its job as a solid Slider without breaking!
It's not expensive and it's a Recommendation product.
View detail
I like that you can choose the length
I bought it because I diverted the 15R1 Rear Sets Kit to 18R1
I like that you can choose from a variety of lengths
However, it is still the ground of Aluminum, so if you can choose the Spec. of Anodized, it will look I think the
View detail
one
It was hard to assemble it to the Handlebar But it is too hard I missed it again:I didn't know it was 1pc A simple explanation is needed View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
Kevlar is cool!
I installed it on my YZF-R25 to do a race
As expected from the Battle Factory
It's accurate and looks GOOD!
I've fallen over a few times, but they protect me well!
View detail